GENERAL Jasper RGH FREEZE

[Martin C]

ok that's fine. 17e has been erased in the build. Not that it matters as you can't write to 17e anyway.

Does it freeze in the exact same place every time?

 

[Aiosforos]

it freezes or in the boot animation or in the dashboard


bro do you want teamviewer to check the images etc by yourself? just to be 100% sure

 

[Martin C]

obtain the right files and manually run ggbuild to rule out anything else.

TV is not an option

EDIT - try the new tool here:

http://team-xecuter.com/forums/showpost.php?p=457885&postcount=1

 

[Aiosforos]

ok i have original nand dump with nanddump.bin
got cpu key on txt file named cpukey.txt
got 1blkey on 1blkey.txt file
all in mytrinity folder of ggbuild
got ldv 9 as the original dump set in options.ini file
i extract all files except filelist.ini on folder 13604

and then i run cmd on ggbuild folder, and execcute this command:
ggbuild -c jasper -d mytrinity -f 13604 updflash.bin

are these right?

 

[Martin C]

check the link in my last post. There's a win tool now.

 

[Aiosforos]

i have that but the previous version
i test and post back... im so pissed off with this jasper

---------- Post added at 15:08 ---------- Previous post was at 15:03 ----------

hmmm as i see here

mine was the big block one of the 16mb jasper nand, maybe that was the problem?

 

[Martin C]

Possibly - pick the one which matches your FlashConfig from NANDPro.

 

[Aiosforos]

mine is the one in red circle, im waitting now for console to boot

 

[Aiosforos]

that was it, the 16 mb jasper differences

console runs perfect now, thanx for all your help


EDIT argrrrrrr still freezes.....

 

[Martin C]

I'm guessing it doesn't freeze with the original NAND in place?

 

[Aiosforos]

update, after some hours of testing, on some boots it freeze on boot animation, like 2/10 boots, and when it dont freeze console works fine... so were ok i suppose

 

[82ross]

Does the fact your dumping dash 13599 and glitching 13604 make any difference?

 

[Martin C]

What are using to do the glitch itself, out of curiosity ?

 

[Aiosforos]

if i return it to stock, update dash and redump to do again the glitch will the stuck problem be solved? any ideas?

 

[WNYConsoles]

I had a Jasper that kept freezing, slow boot, etc. I had 2x 68nf and 1x 68nf and still had issues. After messing around for a few hours I started trying different CoolRunner images and wrote the 16mb Jasper file to a 256mb Jasper and the unit works perfectly so you may want to give that a try.

 

[thedood69]

Aiosforos. Have you looked at your wiring??
The cables cannot pass any where near the power coils, and try to keep the underboard wires (clockers) away from each other. What your describing is very common when the wires run near these areas. If the box is randomly freezing, it aint your nand! Its electrical, not software, this entire hack revolves around tripping the cpu into a stunned state...your "resetter" board of choice "talks" to the cpu. Any electromagnetic radiated energy (EMF) is inducted into these wires very very easily...they are generally unsheilded.

Check this link
http://team-xecuter.com/forums/showthread.php?p=480877

There is a pic with some comments on results, generally all are solved using this method and the cap for Jaspers.

 

[dj_liss]

are your legs on your cap long or short? read my thread here http://www.xecuter.com/forums/showthread.php?t=76802
it may solve boot issues

 

[BKster]

remap it on stock nand, then create ggbuild and after remap it again on the ggbuild nand?

May seem like a dumb question but I want to know...What exactly do you all mean when yall state REMAPPING when flashing the NAND?...

 

[dj_liss]

i always let rawflash or flash 360 handle any bad blocks and never had any probs so far