RGH Jasper Wrote ECC Not Booting

[ScrubbaDubby]

My Jasper RGH2 Demon is not booting the RGH NAND.

It doesn't cycle, just stays red.

I have it switched to NoR, demon switched to XB, and everything to CR installed.

RGH2 caps and whatnots's are installed. (bridged Cap, 2 and 3, removed JP, etc)

Programmed CR with RGH2 A

I have done the fix in Ubergeek's TuT for fixes ( on the FT6U7/Post_out1)

I am using the alternate c4N27 point for R4B24 (STBY_CLK)

But i am getting no luck on cycles.

Soldering Pics:
https://www.dropbox.com/sh/5oc079s7it2t5di/u6VOz6EbbQ

 

[LoneWolf913]

Let's see pictures of the install, as it's probably a soldering issue. What XSVF file are you using?

 

[ScrubbaDubby]

im using the default xsvf that JRunner 280 supplies. I have the updated demon one's provided by TX here on the site, but i don't know how to use them.

I will take pictures give me a minute

 

[LoneWolf913]

RGH1 or 2? There are 4 possible Demon RGH2 XSVFs so there is no 'default' one.

 

[ScrubbaDubby]

RGH 1, i haven't done an RGH 2 install yet so i didnt wanna try on a dual nand jasper

 

[Martin C]

Another Xbox and another thread........

Pics are needed. Infraction given.

 

[ScrubbaDubby]

sorry camera died right after i plugged it in. i g2g to school and its not even my camera so i dont know where the charger is at and the last thing i need is your bullying about how awful my pictures are

 

[BL4K3Y]

the last thing i need is your bullying about how awful my pictures are

Nobody is bullying anybody, we don't tolerate that here.

You should have a working camera to hand so you can provide suitable images for us to help us diagnose your issue.

 

[Martin C]

OP - you know the rules by now.

We CANNOT help you without good pictures.

You are literally creating a new thread per console you work on. We are NOT here to nanny you into learning how to RGH. This is a TX product support forum. Your coolrunner is working. End of story.

I strongly suggest you stop messing with consoles and learn on one of them. You're abusing the good nature of other members due to your unwillingness to learn properly.

 

[hersheys247]

RGH 1, i haven't done an RGH 2 install yet so i didnt wanna try on a dual nand jasper

If your trying to boot .ecc off demon then I believe you need RGH 2.0.

Sent from my brain tumor causing device using Tapatalk.
Please give THANKS and REP+1 if someone helped you

 

[Martin C]

If your trying to boot .ecc off demon then I believe you need RGH 2.0.

Sent from my brain tumor causing device using Tapatalk.
Please give THANKS and REP+1 if someone helped you

Not necessarily. RGH version depends on the CB on your stock console, nothing more.

 

[ScrubbaDubby]

updated. i realized i needed to RGH2 (according to a more experienced friend. Its on 41719 dash) , and now have pics.

 

[Krafter]

Are you still have the same issue? How about some pics of the CR install if so? I also noticed that the top ribbon cable on the DEMON is crooked.


I hate TapaTalk auto correction. Please bare with me.

 

[ScrubbaDubby]

there are pics of the CR install...

 

[Goldensavage]

The red wire in the first image needs to be looked at.

Your ribbon looks slightly off attached to the demon

Also pics of the the actual coolrunner itself install. The unit and the soldering done to that i think Krafter meant.