LITEON 9504 JF not showing the 0x8c

etwgaming · Oct 1, 2013

So, Im flashing a 9504 drive. Heres my problem.
I did the Kamikaze/Windbond hack. Went all the way thru the process to where i press the 0x8c and begin drilling into the chip.
It completes and Spi unlocks. I then "outro" the device, turn off the usbpro, turn it back on and then "intro" device. It goes into vendor mode, but the 0x8c stayed the same and didnt switch to 000x0. (I have always done my mods this way without any problems)

I restarted the process 2 more times with the same result.

On the 3rd attempt as you can see in the picture I dont even get the 0x8c to pop up in the box, but I can take it in and out of vendor mode by hitting the intro/outro buttons.

Disc drive still works and still play games

Anyone able to help me?

playingmax · Oct 1, 2013

try erasing again then intro n see what u get. if nothing then u've gone too deep

jsinger47 · Oct 1, 2013

At this point you can't do anything but lock with ctrl shft f11 and try to unlock again.

In the case of a spelling error, I blame Tapatalk.

etwgaming · Oct 4, 2013

Ok, just attempted another one and got the same problem but this time on a 0225 drive..2 times in a row when it has worked previously numerous times without a problem.
I did the Ctr/Shift/F11 and it did relock it. It allowed me to Spi unlock again. But if I hit "outro" it tells me no drive detected. If I "intro" it pops back up in vendor mode. This time though after I got it too 0x000 I hit "write". As you can see from the log it wrote, but then when it tried to verify it failed. Any chance it could be the CK3i or USBpro?
(I switched back to JF 1.94 cause this only started when I switched to 1.96)

And just my luck..this one now doesnt open or close

Code:

~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~
JungleFlasher 0.1.94 Beta (320)
Session Started Fri Oct 04 11:12:12 2013

This is a 32 bit process running on 2 x 32 bit CPUs 
X360USB PRO detected, Version 0.18

Found 1 I/O Ports.
Found 1 Com Ports.
Found 5 windows drives C: D: E: H: J:
Found 3 CD/DVD drives D: E: H:

Sending Vendor Intro to port 0x0000
Status 0x80
Sending Vendor Intro to port 0x0000
Status 0x80
Re-sending Vendor Intro: 
.......
Serial flash found with Status 0x72

Sending Device ID request to port 0x0000
Spi Status: 0x3C
Manufacturer ID: 0xEF
Device ID: 0x11
Flash Name:  Winbond/NEX(W25P20/NX25P20)
Flash Size:  262144 bytes
Spi Status: 0x8C
Sending Vendor Outro to port 0x0000
Sending Vendor Intro to port 0x0000
Status 0x80
Re-sending Vendor Intro: 
........
Serial flash found with Status 0x72

Sending Device ID request to port 0x0000
Spi Status: 0x8C
Manufacturer ID: 0xEF
Device ID: 0x11
Flash Name:  Winbond/NEX(W25P20/NX25P20)
Flash Size:  262144 bytes
Sending Vendor Outro to port 0x0000
Sending Vendor Intro to port 0x0000
Status 0x80
Re-sending Vendor Intro: 
.......
Serial flash found with Status 0x72

Sending Device ID request to port 0x0000
Spi Status: 0x8C
Manufacturer ID: 0xEF
Device ID: 0x11
Flash Name:  Winbond/NEX(W25P20/NX25P20)
Flash Size:  262144 bytes

Getting Status from port 0x0000
Serial flash found with Status 0x72
Spi is locked, Aborting!
Sending Vendor Intro to port 0x0000

Serial flash found with Status 0x72

Sending Device ID request to port 0x0000
Spi Status: 0x8C
Manufacturer ID: 0xEF
Device ID: 0x11
Flash Name:  Winbond/NEX(W25P20/NX25P20)
Flash Size:  262144 bytes
Loading firmware file C:\Users\ETW\Desktop\JFFW\JungleFlasher v0.1.96 Beta (323)\firmware\LTPlus-0225-v3.0.bin
MD5 hash:  1a38d3a2a6519339599fa1866642c513
Genuine LT plus v3.0
Drive key @ n/a FFFFFFFFFFFFFFFFFFFFFFFFFFFFFFFF
Firmware Osig: [PLDS    DG-16D4S        0225]
Firmware is:  LT-Plus 3.0                     
DVD Key copied to target
Target is LT - ID strings not copied to Target

Getting Status from port 0x0000
SPi flash found with Status 0x72
Spi is locked, Aborting!

Sending Spi UnLock request to Port 0x0000
.....................................
Spi Status: 0x00

Getting Status from port 0x0000
SPi flash found with Status 0x72

Sending Chip Erase to Port 0x0000
Erasing:
Writing target buffer to flash
Writing Bank 0: ................
Writing Bank 1: ................
Writing Bank 2: ................
Writing Bank 3: ................
............
Flash Verification Test !
Reading Bank 0: Dump Failed

Getting Status from port 0x0000
Invalid Status 0x80

Getting Status from port 0x0000
Invalid Status 0x80

Sending Spi Lock request to Port 0x0000
Lock Failed !
Spi Status: 0x00

Sending Spi Lock request to Port 0x0000
Lock Failed !
Spi Status: 0x00
Sending Vendor Outro to port 0x0000
Sending Vendor Intro to port 0x0000
Status 0x80
Re-sending Vendor Intro: 
.........
Serial flash found with Status 0x72

Sending Device ID request to port 0x0000
Spi Status: 0x3C
Manufacturer ID: 0xEF
Device ID: 0x11
Flash Name:  Winbond/NEX(W25P20/NX25P20)
Flash Size:  262144 bytes

Drive in Vendor Mode! DVDkey files extraction aborted! 

Sending Vendor Outro to port 0x0000
Sending Vendor Intro to port 0x0000
Status 0x80
Re-sending Vendor Intro: 
.........
Serial flash found with Status 0x72

Sending Device ID request to port 0x0000
Spi Status: 0x3C
Manufacturer ID: 0xEF
Device ID: 0x11
Flash Name:  Winbond/NEX(W25P20/NX25P20)
Flash Size:  262144 bytes
Spi Status: 0x8C
Sending Vendor Intro to port 0x0000

Serial flash found with Status 0x72

Sending Device ID request to port 0x0000
Spi Status: 0x8C
Manufacturer ID: 0xEF
Device ID: 0x11
Flash Name:  Winbond/NEX(W25P20/NX25P20)
Flash Size:  262144 bytes

Sending Spi UnLock request to Port 0x0000
.......
Spi Status: 0x00

Getting Status from port 0x0000
SPi flash found with Status 0x72

Sending Chip Erase to Port 0x0000
Erasing:
Writing target buffer to flash
Writing Bank 0: ................
Writing Bank 1: ................
Writing Bank 2: ................
Writing Bank 3: ................
............
Flash Verification Test !
Reading Bank 0: Dump Failed

Antalpromille · Oct 4, 2013

etwgaming said:

Ok, just attempted another one and got the same problem but this time on a 0225 drive..2 times in a row when it has worked previously numerous times without a problem.
I did the Ctr/Shift/F11 and it did relock it. It allowed me to Spi unlock again. But if I hit "outro" it tells me no drive detected. If I "intro" it pops back up in vendor mode. This time though after I got it too 0x000 I hit "write". As you can see from the log it wrote, but then when it tried to verify it failed. Any chance it could be the CK3i or USBpro?
(I switched back to JF 1.94 cause this only started when I switched to 1.96)

And just my luck..this one now doesnt open or close

Code:

~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~
JungleFlasher 0.1.94 Beta (320)
Session Started Fri Oct 04 11:12:12 2013

This is a 32 bit process running on 2 x 32 bit CPUs 
X360USB PRO detected, Version 0.18

Found 1 I/O Ports.
Found 1 Com Ports.
Found 5 windows drives C: D: E: H: J:
Found 3 CD/DVD drives D: E: H:

Sending Vendor Intro to port 0x0000
Status 0x80
Sending Vendor Intro to port 0x0000
Status 0x80
Re-sending Vendor Intro: 
.......
Serial flash found with Status 0x72

Sending Device ID request to port 0x0000
Spi Status: 0x3C
Manufacturer ID: 0xEF
Device ID: 0x11
Flash Name:  Winbond/NEX(W25P20/NX25P20)
Flash Size:  262144 bytes
Spi Status: 0x8C
Sending Vendor Outro to port 0x0000
Sending Vendor Intro to port 0x0000
Status 0x80
Re-sending Vendor Intro: 
........
Serial flash found with Status 0x72

Sending Device ID request to port 0x0000
Spi Status: 0x8C
Manufacturer ID: 0xEF
Device ID: 0x11
Flash Name:  Winbond/NEX(W25P20/NX25P20)
Flash Size:  262144 bytes
Sending Vendor Outro to port 0x0000
Sending Vendor Intro to port 0x0000
Status 0x80
Re-sending Vendor Intro: 
.......
Serial flash found with Status 0x72

Sending Device ID request to port 0x0000
Spi Status: 0x8C
Manufacturer ID: 0xEF
Device ID: 0x11
Flash Name:  Winbond/NEX(W25P20/NX25P20)
Flash Size:  262144 bytes

Getting Status from port 0x0000
Serial flash found with Status 0x72
Spi is locked, Aborting!
Sending Vendor Intro to port 0x0000

Serial flash found with Status 0x72

Sending Device ID request to port 0x0000
Spi Status: 0x8C
Manufacturer ID: 0xEF
Device ID: 0x11
Flash Name:  Winbond/NEX(W25P20/NX25P20)
Flash Size:  262144 bytes
Loading firmware file C:\Users\ETW\Desktop\JFFW\JungleFlasher v0.1.96 Beta (323)\firmware\LTPlus-0225-v3.0.bin
MD5 hash:  1a38d3a2a6519339599fa1866642c513
Genuine LT plus v3.0
Drive key @ n/a FFFFFFFFFFFFFFFFFFFFFFFFFFFFFFFF
Firmware Osig: [PLDS    DG-16D4S        0225]
Firmware is:  LT-Plus 3.0                     
DVD Key copied to target
Target is LT - ID strings not copied to Target

Getting Status from port 0x0000
SPi flash found with Status 0x72
Spi is locked, Aborting!

Sending Spi UnLock request to Port 0x0000
.....................................
Spi Status: 0x00

Getting Status from port 0x0000
SPi flash found with Status 0x72

Sending Chip Erase to Port 0x0000
Erasing:
Writing target buffer to flash
Writing Bank 0: ................
Writing Bank 1: ................
Writing Bank 2: ................
Writing Bank 3: ................
............
Flash Verification Test !
Reading Bank 0: Dump Failed

Getting Status from port 0x0000
Invalid Status 0x80

Getting Status from port 0x0000
Invalid Status 0x80

Sending Spi Lock request to Port 0x0000
Lock Failed !
Spi Status: 0x00

Sending Spi Lock request to Port 0x0000
Lock Failed !
Spi Status: 0x00
Sending Vendor Outro to port 0x0000
Sending Vendor Intro to port 0x0000
Status 0x80
Re-sending Vendor Intro: 
.........
Serial flash found with Status 0x72

Sending Device ID request to port 0x0000
Spi Status: 0x3C
Manufacturer ID: 0xEF
Device ID: 0x11
Flash Name:  Winbond/NEX(W25P20/NX25P20)
Flash Size:  262144 bytes

Drive in Vendor Mode! DVDkey files extraction aborted! 

Sending Vendor Outro to port 0x0000
Sending Vendor Intro to port 0x0000
Status 0x80
Re-sending Vendor Intro: 
.........
Serial flash found with Status 0x72

Sending Device ID request to port 0x0000
Spi Status: 0x3C
Manufacturer ID: 0xEF
Device ID: 0x11
Flash Name:  Winbond/NEX(W25P20/NX25P20)
Flash Size:  262144 bytes
Spi Status: 0x8C
Sending Vendor Intro to port 0x0000

Serial flash found with Status 0x72

Sending Device ID request to port 0x0000
Spi Status: 0x8C
Manufacturer ID: 0xEF
Device ID: 0x11
Flash Name:  Winbond/NEX(W25P20/NX25P20)
Flash Size:  262144 bytes

Sending Spi UnLock request to Port 0x0000
.......
Spi Status: 0x00

Getting Status from port 0x0000
SPi flash found with Status 0x72

Sending Chip Erase to Port 0x0000
Erasing:
Writing target buffer to flash
Writing Bank 0: ................
Writing Bank 1: ................
Writing Bank 2: ................
Writing Bank 3: ................
............
Flash Verification Test !
Reading Bank 0: Dump Failed

If it doesnt open och close the tray now its probably becouse you failed this kamikaze. Could be a bad FW but again, you have drilled into the main IC!

etwgaming · Oct 4, 2013

i didnt pay attention to which it uses, but in manually inserting the FW it had either
0225-v3.0.bin or
0225-v3.0u.bin

i used v.3.0.bin ...was that correct?

Antalpromille · Oct 5, 2013

etwgaming said:
i didnt pay attention to which it uses, but in manually inserting the FW it had either
0225-v3.0.bin or
0225-v3.0u.bin

i used v.3.0.bin ...was that correct?

Doesnt matter what D4S FW you are using, it should still eject without a problem.

Search

Search

LITEON 9504 JF not showing the 0x8c

etwgaming

Junior Member

playingmax

jsinger47

etwgaming

Junior Member

Antalpromille

etwgaming

Junior Member

Antalpromille