GENERAL Jr Progammer v2

P

picabo2

Junior Member
Aug 6, 2015
16
0
Good afternoon!

I just started with the XBOX 360 modding and run into a road block.

1) Corona V3 Slim Xbox 360
2) Latest Dash
3) Corona Postfix adapter v2 installed.


I disconnected the power for the CR4 XL until I can get the JR Programmer v2 to work. I assume this is okay and won't cause issues. I did a direct wire install and connected the 7 wires back to the JR Programmer v2. My PC (windows 7, and windows 10) is able to detect the programmer. I was able to reflash the programmer in bootloader mode and it flashed and completed sucessfully. I took it out of bootloader mode and it installed a driver. I shows up under devices, but does not show an actual driver. (see screenshot). I click on read Nand and it power on, and nothing happens. Am I missing a step or need to do something different? Any help would be appreciated.





 
Nintendo

Nintendo

VIP Member
Sep 5, 2014
605
33
Spain
picabo2 said:
Good afternoon!

I just started with the XBOX 360 modding and run into a road block.

1) Corona V3 Slim Xbox 360
2) Latest Dash
3) Corona Postfix adapter v2 installed.


I disconnected the power for the CR4 XL until I can get the JR Programmer v2 to work. I assume this is okay and won't cause issues. I did a direct wire install and connected the 7 wires back to the JR Programmer v2. My PC (windows 7, and windows 10) is able to detect the programmer. I was able to reflash the programmer in bootloader mode and it flashed and completed sucessfully. I took it out of bootloader mode and it installed a driver. I shows up under devices, but does not show an actual driver. (see screenshot). I click on read Nand and it power on, and nothing happens. Am I missing a step or need to do something different? Any help would be appreciated.





Click to expand...
Oh, that soldering man. You have to install the drivers that came with JRunner, just override Driver signature and use those drivers.
 
P

picabo2

Junior Member
Aug 6, 2015
16
0
lol... sorry about the soldering. I probably should clean it up, but didn't want to keep heating up the board. I had to remove a fake QSB from there!
There should not be a problem with powering it on without its DVD driver?

So it is recognized in jrunner now. When I click on READ NAND it powers on, says Version 10, Flash Config 0x000000 can not continue, then powers off.
Thanks,
 
Nintendo

Nintendo

VIP Member
Sep 5, 2014
605
33
Spain
picabo2 said:
lol... sorry about the soldering. I probably should clean it up, but didn't want to keep heating up the board. I had to remove a fake QSB from there!
There should not be a problem with powering it on without its DVD driver?

So it is recognized in jrunner now. When I click on READ NAND it powers on, says Version 10, Flash Config 0x000000 can not continue, then powers off.
Thanks,
Click to expand...
There's no problem if you power it on without the DVD Drive. that flashconfig error is because of the soldering, retouch the points.
 
Nintendo

Nintendo

VIP Member
Sep 5, 2014
605
33
Spain
P

picabo2

Junior Member
Aug 6, 2015
16
0
lol... sorry about the soldering. I probably should clean it up, but didn't want to keep heating up the board. I had to remove a fake QSB from there!

I got it to read all the way through the .bin once. It had a lot of errors but finished. I looked at the resistor bridging and it said only bridge if the resistor is missing. Looks like my R2C10 is in place so I should not have to do anything. Now it says reading nanddump1.bin can not continue.

 
P

picabo2

Junior Member
Aug 6, 2015
16
0
Ok got to a point where I can read nand, create ecc, write ecc, but when I create XEbuild, I get wrong CPU key.

Thanks!

Josh
 
Last edited:
Nintendo

Nintendo

VIP Member
Sep 5, 2014
605
33
Spain
picabo2 said:
Ok got to a point where I can read nand, create ecc, write ecc, but when I create XEbuild, I get wrong CPU key.

Thanks!

Josh
Click to expand...
That's beacuse you don't need to create XeBuild now, just create ECC and write it.
 
P

picabo2

Junior Member
Aug 6, 2015
16
0
I was reading a little more, and found that I have to book to xell, get my CPU key then I can write the custom XEbuild. Now when I plug in the 360 it makes the ding sound when I hot the eject and power button, but does not spin up any more. No more boot screen. Just sits there and dings occasionally. If its its not one thing its another!
 
You must log in or register to reply here.