JASPER JRP flash config error with direct wire install Phat Jasper

[nikko058]

hi all i know ive been posting alot lately but i messed up my QSB kit and i cant get another so i tried a direct wire install now im getting Flash Config error and before you say the cause i am aware that the main cause of this problem is a bad solder job ive checked time and time again with mulimeters and magnifine glases and there arent any points touching and btw i used the pinout here

http://team-xecuter.com/forums/thre...SB-DIRECTLT-TO-THE-MOBO?p=1047963#post1047963

its the second picture because im using a phat

so what am i doing wrong here is the pinout incorrect or something or what im so confused.....

thanks in advance!!!

 

[ablegepu]

If you are positive that the wires are correct and the soldering is good and you have double checked continuity, then the spi is probably blown in the south bridge and you will need to use a parallel programmer such as the demon to read and write the nand.

 

[scott1503]

post a picture of the wire install its likely that you have a faulty connection or a wire in the wrong place, no1 wire I would check is yellow(ground) which always seems a to be a little tricky on certain consoles

 

[nikko058]

i got that part fixed but of course there's always something else if i unplug the power to the console and plug it back in and restart the JRP mobo then when i click READ NAND it gives me this....

Version: 10
Flash Config: 0xFFFFFFFF
Error: 000 reading block 0
Error: 000 reading block 1
Error: 000 reading block 2
Error: 000 reading block 3
FFFFFFFF
Jasper 256MB Manually Selected
Reading Nand to C:\Users\Nikkoli\Desktop\J-Runner v3 (5) Core Pack\J-Runner v3 (5) Core Pack\output\nanddump1.bin
Can not Continue

what the heck is happening?

 

[scott1503]

the flash config relates to either a fault in the wires or if I remember correctly a faulty spi. so if you post a picture someone will advise

 

[nikko058]

here forgive the quality guys i had to use my phone....

and i am well aware that the solder job is total crap lol ive been doing it for 3 and a half years but i never said i was good at it XD

http://imgur.com/h0DzlnQ

http://imgur.com/jFSmG2y

sorry im not sure how to put photos in the message lol

 

[GeekHeat]

Soldering is bad. Also wires are in wrong place.
Wont let me upload an IMG for some reason.

http://team-xecuter.com/forums/threads/84696-NAND-X-J-R-Programmer-Wire-Install-Guide

 

[nikko058]

Soldering is bad. Also wires are in wrong place.
Wont let me upload an IMG for some reason.

http://team-xecuter.com/forums/threads/84696-NAND-X-J-R-Programmer-Wire-Install-Guide

could you give me the correct pinout then or did i misinterpret the last one because i assure you there was nothing touching on that board
or could you show me a picture of a working one so i can see the wire placement?

 

[XeGooch]

Your Red and Brown where should be switched around. Soldering isnt to bad should work to read nand.

 

[scott1503]

red and brown need switching and your soldering could use a little work the blob of solder on each point should give you a good enough connection but I would try to remove some of the excess solder

 

[nikko058]

OKAY I GOT IT NOW THANKS but now i have one more issue i dont know the process for J-runner and i haven't found a tutorial for the CR4 Phat consoles ive searched for an hour now can anyone fully tell/show me how to do the RGH2 process with CR4 and J-r Programmer for phat consoles ive already read the nand but im clueless as to what to do next