JTag equipment for two 360's

T

tobad

Junior Member
Jan 20, 2011
23
0
Hey guys,

I'm one of the lucky ones who has a jtaggable 360, to be correct I have two jtaggable 360's!

I hope my question is not too bad! But I'm a bit confused!

I want to jtag both 360s: both are untouched, not even DVD FW flash.
1: XBOX 360 PAL manufactory date: 2008-07-11;with HDMI
2: XBOX 360 PAL manufactory date: 2008-07-05;with HDMI

I hope in this bundle is everything included that I need for my first 360:
Team Xecuter Nand-X USB 360 Programmer Kit

So... what do i need for my second one?
Just the Quick Solder Bords? Xecuter NAND-X QSB Install Kit
or do I need also the Xecuter Non-Xenon JTAG Kit (Kit #2) or also the Xecuter Non-Xenon JTAG Alt Kit (Kit #5)

I hope this question doesn't sound too bad! I will pay for this product so please keep beeing respectful.

I'm sorry for my english. Does somebody know if I can buy this products in germany?

Thanks!

just, tobad!
 
K

krayx

Full Member
Jan 31, 2011
66
0
Im sure there isnt much diffrence, Pretty sure The Programmer Kit can do them both.
 
T

tobad

Junior Member
Jan 20, 2011
23
0
krayx said:
Im sure there isnt much diffrence, Pretty sure The Programmer Kit can do them both.
Click to expand...
yeah but i would have to desolder the parts i used in the first 360.

but i just want to solder one time on each 360. i though this is the way this kit is meant to be used.
 
K

krier023

VIP Member
May 30, 2010
249
0
You are very correct. You will need the nandx programming kit, and that comes with 1 set of easy solder pcbs and one jtag install wiring. Jtag wiring is needed seperate for each xbox.(you will need either of the non-xenon kits they work the same if youre good at soldering) And you will have to buy another easy solder pcb kits.

If you are tight on money though, you can cut the wires on the nandx and do a direct install wiring. this way you would not have to buy an extra nandx easy solder pcb kit.

Use jtag tool as it is easy to use, and look into the alternate smc points on jtag tool because they are very helpful when soldering on non xenon boards.
 
J

jfelding

VIP Member
Feb 9, 2010
687
0
Denmark
Sounds like you've got two explotable Jaspers. Damn, your a lucky guy :p..
And yes, you will need two JTAG-wiring for post-Xenon boards. One is included in the standard kit, and yes, you can buy an extra QSB-pack or a few diodes and some wire.
The QSBs are not as easy to solder as wires, but its really not hard with some flux, and it has great options. A multimeter is always good to have. A necessity really.

As you can read in the tuts, the NAND-X has three methods for NAND reading/writing. Any of these can be used, soldered, desoldered and reused (although doing this with the qsbs might be difficult). If you dont wanna desolder you can buy extra QSBs/Pins as well.
 
K

kosyer

Noob Account
Dec 31, 2010
6
0
you are lucky? <.< i got 7 jtagg consoles........... 1 jasper, 3 falcon, 3 xenons....
 
M

marshamods

VIP Member
Mar 7, 2010
1,905
0
ohio
wow your special, what do you will those jtags? Black Ops and MW2 mods with your 12 year old followers :eek:
 
You must log in or register to reply here.