Jungleflasher won't recognize drive?

H

hereyougo72

Junior Member
Dec 25, 2011
11
0
Upland, CA
I successfully install ck3i and x360 USB pro drivers. When I try I plug my slim fw 0401 into the computer on jungle flasher under DVD key32 on drive properties it says "no drive detected!"

Also my ck3i has lights off when plugged in:


And lightS on when not plugged in:


Not sure if that's abnormal at all, but I figured I might as well give as much info as possible.

Any ideas?
 
B

bittersuit_98

Full Member
Jan 14, 2012
61
0
maybe you can try feeding power to the drive using the console itself as power source instead of the ck3i just to see if it's detected by JF.

Also, did you try the eject button on the ck3? is it working at all?

Seems to be a power supply issue.
 
  • Like
Reactions: hereyougo72
hilly360

hilly360

VIP Member
Dec 17, 2011
226
33
DURHAM, North East. UK
looking at picture you have the power cable wrong way round!! green cables should be showin at the top at both ends.

you got red cables showin up at drive end of power cable.

try that then hit the red THANKS button lol......
 
  • Like
Reactions: keil423 and hereyougo72
reefz3ro

reefz3ro

VIP Member
May 30, 2011
669
0
Pittsburgh, PA
its hard to tell the position of the on off switch on the ck3i in first and second pic but....
in your first pic the power to to the drive from the ck3i is turned off.... so no drive would show up

plus it is in modeB i don't know that that makes a difference but it should be blue for modeB off.

is your molex power supply 5v or 12v? I believe if you have only a 5v molex the ck3i will not eject the drive(anyone correct me if i'm wrong)
 
Last edited:
  • Like
Reactions: hereyougo72
DrunkenNinja

DrunkenNinja

VIP Member
Oct 3, 2011
1,048
88
RGH
Ck3i should power the drive you want to flash with (1) connection "green / red cable" between CKi and drive, the CKi should then be powered by a Molex power supply or connection

X360usb pro should be connected to your laptop by USB and then connected via a Sata to Sata cable to the drive, this enables data transfer.

That should get you up and running, it's hard to see what your doing from the photos but it does not look right to me.
 
  • Like
Reactions: hereyougo72
H

hereyougo72

Junior Member
Dec 25, 2011
11
0
Upland, CA
keil423 said:
Good thing they put that new safty feature in the CK3i that detects when you plug the drive in wrong. Otherwise you would have just fried you drive.:facepalm:
Click to expand...
Thank- team Xecuter.


I also have a new problem. I've installed TX Replacement pcb its now undetected by Jungleflasher.

Picture:

View attachment 6583

Also unresponsive with the ck3i. I'm thinking i've installed it wrong?
 
krypt1c

krypt1c

VIP Member
May 23, 2010
974
48
Nottingham
Have you wrote the firmware to the drive? As they are shipped blank so will be unresponsive till you have flashed your firmware to it. As dgenx has pointed out its in the tutorial.
hereyougo72 said:
Thank- team Xecuter.


I also have a new problem. I've installed TX Replacement pcb its now undetected by Jungleflasher.

Picture:

View attachment 6583

Also unresponsive with the ck3i. I'm thinking i've installed it wrong?
Click to expand...
 
Last edited:
  • Like
Reactions: hereyougo72
You must log in or register to reply here.