Kprobe Liteon Burn Quality Testing Tool
- Thread starter Ubergeek
- Start date
Two Traxdata XGD3 burns using MSCE modified firmware (Ritek S04-066 to D01-001) to enable 2.4x burning as burning at 4x causes verify failures.
Burned with different settings as noted below. Even though both verify 100% and install to Xbox harddrive, my personal opinion is to stick with Verbs for XGD3. I did this just out of curiosity.
Image below:
@2.4x
Smartburn = Enabled
Force Hyper Tuning = Disabled
Online Hyper Tuning = Disabled
OPC = Enabled
Image below:
@2.4x
Smartburn = Enabled
Force Hyper Tuning = Enabled
Online Hyper Tuning = Enabled
OPC = Disabled
Burned with different settings as noted below. Even though both verify 100% and install to Xbox harddrive, my personal opinion is to stick with Verbs for XGD3. I did this just out of curiosity.
Image below:
@2.4x
Smartburn = Enabled
Force Hyper Tuning = Disabled
Online Hyper Tuning = Disabled
OPC = Enabled
Image below:
@2.4x
Smartburn = Enabled
Force Hyper Tuning = Enabled
Online Hyper Tuning = Enabled
OPC = Disabled
Last edited:
Burned my own 0800 rip of Gears of War 3 on a crappy Memorex (RITEK, not Moser Baer). Skipping posting the Verb, as that burn was flawless. Thanks c4eva! Settings and graph image follow:
Speed = 4x (OPC on)
Smartburn = Enabled
Force Hyper Tuning = Disabled
Online Hyper Tuning = Disabled
Graph:
Speed = 4x (OPC on)
Smartburn = Enabled
Force Hyper Tuning = Disabled
Online Hyper Tuning = Disabled
Graph:
Speed 4X (Opc On)
Smartburn = enabled
Force Hyper Tuning = enabled
Online Hyper Tuning = enabled
Take it this is a good quality burn. I will update with outher disk's, they arrive later today and compare my results.
Smartburn = enabled
Force Hyper Tuning = enabled
Online Hyper Tuning = enabled
Take it this is a good quality burn. I will update with outher disk's, they arrive later today and compare my results.
Last edited:
got two drives that scan consistently like these two, then one drive like the bottom, same firmware, same settings, opc on with FHT AND OHT on, mkm-003, same deal on mkm001, so there are dud drives out there
last one scans like this
last one scans like this
knowlzy10
BANNED
I am reading this on iphone and the spike looks like its on the layerbreak which should be ok
Unless i am looking at the wrong picture lol
4X
SmartBurn and OHT ON
Singapore Verbs (normal Surface, non Printable)
GoW3
OPC OFF
Same Disc scanned with my other LiteOn
OPC ON
Note: ImgBurn gave an Error when it tried to verify the succesful burn. (Sector 2133538 is 208E22 in hex)
Same Disc scanned with other Drive
SmartBurn and OHT ON
Singapore Verbs (normal Surface, non Printable)
GoW3
OPC OFF
Same Disc scanned with my other LiteOn
OPC ON
Note: ImgBurn gave an Error when it tried to verify the succesful burn. (Sector 2133538 is 208E22 in hex)
Code:
W 13:20:24 Failed to Read Sector 2133538 - Reason: L-EC Uncorrectable ErrorSame Disc scanned with other Drive
Last edited:
holy crap thats bad
---------- Post added at 06:03 ---------- Previous post was at 06:03 ----------
Can you post your results with OPC enabled please
Tried with OPC.
IMGBurn gave me Verification error after burning.
I will update my post with its kprobe result.
If you look, the Nero quality score was 93 which is greater than the 90 that über recommends. The point of the graphs were to show inconsistencies between the 2 programs. You still have to use some judgement in determining whether the scan is good enough for you.
Furthermore, PI errors can spike as high as 200 and PIF errors as high as 10. The point being, as long as the values don't remain high the disc is fine. Mind you this is a disc quality check, so naturally the lower the values the better. The higher the values, the more work a laser has to perform to read the disc. Consistent high values may mean an unreadable disc at various points during the game.
The guide is just that, a guide. It is not definitive.
Last edited:
iHAS 124 B
Smartburn = enabled
Force Hyper Tuning = enabled
Online Hyper Tuning = enabled
OPC = enabled
Burn Speed = 4x
Nvidia MCP61 Chipset
Windows 7 x64
I just dont seem to be getting good clean burns. Im using vetribatim mk 003 and burning at x4. Should i try with OPC disabled and burn at 2.4 speed.
Thanks mark
knowlzy10
BANNED
When i run through nero with my ihas124, the options of the read speed is 8x or maximum, why cant i test it at 4x ? i tried manually setting it in the options but it still wont work?
EDIT - just realised that the speed when running the test is at 3.92x but then increases during the test to like 6x. But, why are my results so rubbish all the time? i just seem to get different results everytime! im using verb 003 and the best nero disc score ive got is 84, then on other tests i get 64 :S, kprobe tests are always different also
EDIT - just realised that the speed when running the test is at 3.92x but then increases during the test to like 6x. But, why are my results so rubbish all the time? i just seem to get different results everytime! im using verb 003 and the best nero disc score ive got is 84, then on other tests i get 64 :S, kprobe tests are always different also
Last edited:
x360ccm
BANNED
you have a refresh tab at the side of were it say 8x click it and it will give you a option to change it.:rolleyes2:
I actually did that twice and it didnt change, did it again and it did. Just my luck i guess making myself look silly :facepalm:
Two scans, both with SmartBurn, OnlineHyperTuning and ForceHyperTuning enabled. The first burn was at 4x and the second burn was at 2.4x with with MCSE write strategy switch.
PS: Yes, these are AOne Plus/Gold discs and I know they are trash but I had some left and thought I'd check them out.
PS: Yes, these are AOne Plus/Gold discs and I know they are trash but I had some left and thought I'd check them out.
Last edited: