Have you checked all of the repaired traces with a multimeter?
Top right hand cut, is that repaired? Hard to tell from the photo.
Top right hand cut, is that repaired? Hard to tell from the photo.
Liteon 74850c - Jungle Flasher Tutorial
- Thread starter Xecuter
- Start date
- Status
its a little piece of solder in there lol.... i know it doesn't look like much but im using a multi meter and getting 0.9 - 1.0 going through there.... no luck there....
Teajunkie
VIP Member
Got it!!!!!!!!!!!!!!! Thanks guys..... Yeah silly me the cable wasnt firmly plugged in thanks and this forum rocks
Hey Im trying to Flash a Liteon 74850c using my CK3 and My Probe 2 i have the Probe in standby (orange light) the blue light is lit and the CK3 is Lit Blue... im sort of trying to make sure i have the right things switched on my CK3 because im not getting the green light probing R707 if i could get some help or some ideas that would be great thanks
Yeah its me again
Yeah its me again
prove v2 and r707 ha maybe you should follow the directions
http://team-xecuter.com/forums/showthread.php?t=54442
http://team-xecuter.com/forums/showthread.php?t=54442
yeah im not a guy who just posts i been looking around and seem to be doing everything right probe its orange and blue but when i touch R707 nothing reacts i even tried the alternative... the lower left pin in the cluster...still nothing no green
Hi ive been trying to flash my 360 for a week now i followed everything and i know how to read but i still keep getting the 0x51 error wont let me do the L-O-Erase and its so frustrating i have a onboard sata and im using conectivity kit pro connecting it with a usb and i have the 74850c so any help will be much appreciated and also i have the 1.50 firmware i took it to some guy to do it for me months ago and just want to upgrade now to the new version
BGAMods
VIP Member
so its a preflashed liteon? if so you need to hit dummy from iextreme. this will drop your key for youand then autoload your required firmware. then hit liteon erase and write. outro the drive and your done. its that simple. have you been trying to probe a preflashed drive?if youd read the jf tut youd know all this already.
BGAMods
VIP Member
are you serious?
try reading the tutorials for the probe v2 and theres a whole section on dumping the 7 series.
try reading the tutorials for the probe v2 and theres a whole section on dumping the 7 series.
BGAMods
VIP Member
I just wanted to tell you that I recently successfully flashed my Liteon 74850c
I used the CK3 Probe II, first in v1 mode to read the key, and then out of curiosity I did the full MRA dump using v2 mode (also: key x2 = safer!).
I had some problems when doing the MRA dump due to me timing wrong and pressing the switches in the wrong order, but I eventually got it right. My solders unfortunately became really ugly, however they got verified by my Fluke multimeter so I'll pray they stay that way
For the record; I used this guide along with this MRA dump tutorial, and a video guide (which I cant find right now) from this site/forum, and also the JungleFlasher tutorial.
Anyway, thank you for this great community and Team Xecuters awesome products!
I used the CK3 Probe II, first in v1 mode to read the key, and then out of curiosity I did the full MRA dump using v2 mode (also: key x2 = safer!).
I had some problems when doing the MRA dump due to me timing wrong and pressing the switches in the wrong order, but I eventually got it right. My solders unfortunately became really ugly, however they got verified by my Fluke multimeter so I'll pray they stay that way
For the record; I used this guide along with this MRA dump tutorial, and a video guide (which I cant find right now) from this site/forum, and also the JungleFlasher tutorial.
Anyway, thank you for this great community and Team Xecuters awesome products!
BGAMods
VIP Member
thanks for sharing mate. its a real simple process that can be over-complicated by people but if you take your time theres nothing that can go wrong. glad it worked for you.
Yeah it's not complicated at all, at least not with these great tutorials. And besides the soldering, it doesn't requires any special skill at all.
The hardest part was remembering all the steps, because it's quite uncomfortable and hard to browse the internet with one hand while you're holding the probe with the other, especially when you're sitting on the floor beneath your computer. And yeah, I actually ended up doing that, because I was too afraid of letting the probe off the points after I started the procedure
But eventually I found out that it didn't do any harm (as far as I could tell), and after I paused and tried again it went just fine.
By the way, what would the symptoms be (if any), if my solders went loose or somehow bad? From what I've read, when you're flashing you'd see some bad lights on the LT Switch, or JF not being able to read/flash. But would I notice it now anyhow when my drive's being used in the xbox?
The hardest part was remembering all the steps, because it's quite uncomfortable and hard to browse the internet with one hand while you're holding the probe with the other, especially when you're sitting on the floor beneath your computer. And yeah, I actually ended up doing that, because I was too afraid of letting the probe off the points after I started the procedure
But eventually I found out that it didn't do any harm (as far as I could tell), and after I paused and tried again it went just fine.
By the way, what would the symptoms be (if any), if my solders went loose or somehow bad? From what I've read, when you're flashing you'd see some bad lights on the LT Switch, or JF not being able to read/flash. But would I notice it now anyhow when my drive's being used in the xbox?
BGAMods
VIP Member
ive never seen it before mate but at a guess id say the drive would just stop working and responding.
- Status