Little Problem with SX PRO and Force Update 6.1...

AkhikoFR

Noob Account
Nov 28, 2018
5
0
I using SX PRO, i have force update my nintendo switch with RajNX and ChoiDuJourNX (5.1->6.1) and SX OS not loaded on this forced version ... RajNX loaded while the SX OS not loaded on this.. Help me Please
 

slamride

Senior Member
Nov 28, 2018
229
28
I think I understand that after 6.1 update SXOS not working? Update you version of SXOS first it may be on older unsupported version
 

AkhikoFR

Noob Account
Nov 28, 2018
5
0
I have updated SXOS version and not working.. I have downgrading in 5.1 , launch SX OS with SX PRO and working, i not understand x) (I have update SX OS with Xecuter Website 2.3 Beta and the SX OS menu in 1.4 while i have update this in 2.3..) In .zip i have just boot.dat
 
Last edited:

slamride

Senior Member
Nov 28, 2018
229
28
Is the sd card in exfat?
Did you select 6.1 or 6.1 exfat when asked by ChoiDujourNX?
If sd card is exfat when updating you have to use 6.1 exfat option or card is not supported. SXOS will not be able to read boot.dat
 

slamride

Senior Member
Nov 28, 2018
229
28
Update by SXOS using ChoiDujourNX under homebrew menu ...don't use Reinx everything can be done by SXOS
When you get to the point you select "6.1" or "6.1 exfat" choose "6.1 exfat"
This will install the update 6.1 as well as the exfat update
I think your sd card is in exfat and when Switch reboots to 6.1 it can't read it and does not start boot.dat
The 6.1 exfat update will allow it to
 

AkhikoFR

Noob Account
Nov 28, 2018
5
0
With SX OS and ChoiDuJour = Black Screen in 5.1, i have tested xD, other solution is 6.1 not exfat ? (I have choose 6.1 exfat is bad ? x) )
 

imprezgc8

Bannnnnn-Kai!
Staff member
Troll Eating Dogs
Nov 26, 2007
2,424
138
The Cloud
What is the reason for upgrading to 6.1? Initially you say SX is not working after you updated to 6.1, but a little below that you say it's not working in 5.1 after I assume you downgraded. It sounds like you are not using emunand so did you have autoRCM turned on? It's possible that you booted to OFW 6.1 and it probably burned your fuses so you cannot downgrade at this point back to 5.1. I believe even if you use Choi..NX to upgrade without burning the fuses and boot to OFW it will still then burn the fuses.
 

slamride

Senior Member
Nov 28, 2018
229
28
seems fuses would burn since you said SXOS didnt work in 6.1...it booted to OFW instead(burning fuses)
"In .zip i have just boot.dat" Does this mean you did not unzip ...unzip and put boot.dat on root of sd card ...not the .zip
(I have choose 6.1 exfat is bad ? x) Exfat update not bad some have issues using exfat formatted sd cards and prefer fat32. After update either will work.

 
Last edited:
  • Like
Reactions: AkhikoFR

AkhikoFR

Noob Account
Nov 28, 2018
5
0
SX OS Working in 5.1 except that not upgraded in 6.1 with ChoiDuJourNX because Black Screen in ChoiDuJourNX launch... In 6.1 upgraded with RajNX and ChoiDuJourNX, SX OS not launch, I have downgraded this in 5.1 it's good except that i have my SX OS in 1.4 (I have updated with new Boot.Dat (UnZipped Boot.Dat) and not in 2.3, that's why i wanted to increase my firmware version of my nintendo switch x) I need new tab cheat in my SX OS ! xD (Sorry for my bad english traduction, i'm french x) )
 
Last edited:

AkhikoFR

Noob Account
Nov 28, 2018
5
0
I have found (This is my bad, first, i have unzipped in my desktop and delete Boot.dat in my sd and sliped in) Thanks for your helps men's !
 

slamride

Senior Member
Nov 28, 2018
229
28
Glad you found it . The language translation did cause confusion but wanted to try and help.
 

slamride

Senior Member
Nov 28, 2018
229
28
After thinking and going back over post I see where issue was.
When booting in 5.1 SXOS worked with version 1.4
After updating to 6.1
6.1 was not supported by SXOS 1.4 so it would not work properly
boot.dat was issue
You should be able to use ChoiDujourNX after the SXOS 2.3 update