LITEON 83850 v2 Messed up on MRA

[marshamods]

you can still probe pin 101 as normal even when its dead.

exactly. Just probe the whole that you see where the pad used to be and probe pin 122. Then you would repair the way flash showed you. Simple as.

---------- Post added at 18:51 ---------- Previous post was at 18:49 ----------

lol sorry mate. ok i wont do it for free. its just i miss key recoveries, they were good times.:rolleyes2:[/QUOTE]
They were fun, only when you started have to lifting pins or transplants.

 

[lil BLu3 SMuRF]

you can still probe pin 101 as normal even when its dead.

---------- Post added at 02:49 ---------- Previous post was at 02:48 ----------



lol sorry mate. ok i wont do it for free. its just i miss key recoveries, they were good times.:rolleyes2:

Ok, well sorry but I'm probing 122 (red) and 101 (green)

Its on PROBE switch, 20 ohm, clicked the button and turned on and still nothing. What do I do?

 

[lil BLu3 SMuRF]

Ok, well sorry but I'm probing 122 (red) and 101 (green)

Its on PROBE switch, 20 ohm, clicked the button and turned on and still nothing. What do I do?

BTW, I've tried 18 and 22

 

[conie]

Cost less than $3 to send a PCB to the UK. Do it.

 

[lil BLu3 SMuRF]

Cost less than $3 to send a PCB to the UK. Do it.

How long would it take? And it costs money to buy a new replacement drive.

 

[BGAMods]

itd take 2 minutes to extract the key and email it.

 

[lil BLu3 SMuRF]

itd take 2 minutes to extract the key and email it.

Well, that will be definitely my last resort, but first how do I get the drive to show up in JF? Like what exactly must I do on the probe. From turning it on to intro'ing to ect.

Also, how long would it take to ship?

 

[conie]

My guess is 1 week in transit. But being in your position I would send it to flashing360 without thinking twice. His service is valuable ($24) and he is offering it for FREE.

If you need a new PCB I can supply you with one for $20 shipped. Ill even flash your key and the latest CFW for free! Or, ask him to send you a new PCB.

 

[XSileX]

Just go with what conie is offering!

 

[lil BLu3 SMuRF]

My guess is 1 week in transit. But being in your position I would send it to flashing360 without thinking twice. His service is valuable ($24) and he is offering it for FREE.

If you need a new PCB I can supply you with one for $20 shipped. Ill even flash your key and the latest CFW for free! Or, ask him to send you a new PCB.

Would you extract my key if you could? If not I'll just send to flashing 360 because I'm assuming your in US right?

 

[BGAMods]

marshamods could get that key no probs and hes in the US.

 

[lil BLu3 SMuRF]

marshamods could get that key no probs and hes in the US.

I PM'd him but still I would like to try to fix it myself before I send anything off.

So how would I get my drive showing up in JF?

 

[ProTaper]

I PM'd him but still I would like to try to fix it myself before I send anything off.

So how would I get my drive showing up in JF?

Fix your traces and it will show up, when you did your trace cuts you cut some important traces.

 

[BGAMods]

set the probe to mra and try again.

 

[ProTaper]

If all fails send your mess up to marshamods.

 

[BGAMods]

i wouldnt exactly call it a mess.

 

[ProTaper]

i wouldnt exactly call it a mess.

Then what would I be called? I can think of no other name for this..

 

[BGAMods]

hes lifted 1 pad which takes 10 seconds to sort. check mine or tj's site to see messes.

 

[ProTaper]

hes lifted 1 pad which takes 10 seconds to sort. check mine or tj's site to see messes.

Yeah those are pretty horrible! Looks like they put a blindfold on an tried to use a welder. lol

 

[BGAMods]

yep, mra is childs play and tbh to the op, why are you still doing it when you could just use the probe 3?