Monitor Com Not working?

-DoC-

VIP Member
Jul 23, 2004
682
48
US
Nothing will show up in the comm window until it glitches and xell boots. It will just tell you the port is open.

Now if the dgx stops blinking and you don't have anything in the monitor window reply back. Otherwise you have to get that console to glitch before going any further.

Sent from my DROID RAZR using Tapatalk 2
 

tntgoesboom

BANNED
Sep 5, 2012
12
0
Oregon
Nothing will show up in the comm window until it glitches and xell boots. It will just tell you the port is open.

Now if the dgx stops blinking and you don't have anything in the monitor window reply back. Otherwise you have to get that console to glitch before going any further.

Sent from my DROID RAZR using Tapatalk 2
That doesn't make any sense how you worded it.
 

Martin C

VIP Member
Jan 10, 2004
35,981
0
Scotland, UK
www.team-xecuter.com
COM monitor will only output once XeLL starts to load. You don't need COM monitor for XeLL to load, so it's not dependent on it to complete the process. You do however need to boot to XeLL in order for COM monitor to be of any use, so the dependency is in that direction.
 

tntgoesboom

BANNED
Sep 5, 2012
12
0
Oregon
COM monitor will only output once XeLL starts to load. You don't need COM monitor for XeLL to load, so it's not dependent on it to complete the process. You do however need to boot to XeLL in order for COM monitor to be of any use, so the dependency is in that direction.
Well my Xbox that I am currently trying to Monitor Com is a Corona. Therefore Xell doesn't appear on the screen. I am just trying to get my CPU key. Also I know you can get it from the IP address but I can not grab the Coronas IP. I know it is 10.0.0.2 but J-Runner doesn't recognize it. Therefore my last resort is it Monitor Com.
 

-DoC-

VIP Member
Jul 23, 2004
682
48
US
Is your console glitched?
From what you said earlier it doesn't appear to be because you had no idea how long it takes.

Does your green light continue to blink?

Sent from my DROID RAZR using Tapatalk 2
 

tntgoesboom

BANNED
Sep 5, 2012
12
0
Oregon
Is your console glitched?
From what you said earlier it doesn't appear to be because you had no idea how long it takes.

Does your green light continue to blink?

Sent from my DROID RAZR using Tapatalk 2
No, It has not glitched yet. The green light was not continuing to blink but when I unplugged the AV cable and booted it again it is continually blinking. Is the Green light blinking a good thing? How long should it take?

*Edit* Green light had stopped blinking somewhere in the first 30 minutes.
 
Last edited:

tntgoesboom

BANNED
Sep 5, 2012
12
0
Oregon
I'm going to go to bed now, This still hasn't been fixed. Currently have been waiting 30 minutes and all Monitor Com says is Port opened. I would appreciate any helpful suggestions anyone is willing to post. I will post back tomorrow with any good/bad news.
 

-DoC-

VIP Member
Jul 23, 2004
682
48
US
If it stopped blinking its likely glitched.
What I normally do is close the comm port. Turn on the console then will open the comm port. Sometimes when I turn off the console and back on with the comm port open it won't show anything.

Also hook it up to your network and try scanning your IP range once the console is glitched.
I use a USB cable directly off the qsbs and never had a problem. I never went through the x360usbpro

Sent from my DROID RAZR using Tapatalk 2
 

Antalpromille

VIP Member
Aug 4, 2011
3,146
0
Borås, sweden
why are there no pictures of what you have done?
i had some consoles that actually needed AV/hdmi connected to boot after succesfull glitch, and with hdmi it also need the handshake from the tv.
 

Joo C

VIP Member
Dec 2, 2011
748
48
South Africa
With the usbpro2 hooked up I open JF and when the correct port is selected JF will tell you CK3i is enabled, this is my sanity check...I then make sure the same port is selected in JR before I open port and power on the console
 

tntgoesboom

BANNED
Sep 5, 2012
12
0
Oregon
If it stopped blinking its likely glitched.
What I normally do is close the comm port. Turn on the console then will open the comm port. Sometimes when I turn off the console and back on with the comm port open it won't show anything.

Also hook it up to your network and try scanning your IP range once the console is glitched.
I use a USB cable directly off the qsbs and never had a problem. I never went through the x360usbpro

Sent from my DROID RAZR using Tapatalk 2
Well it is not glitched. However when I hook it up to my router and boot it the green light goes away within the first minute but I it [email protected]!! Thank you!!!!!
 

-DoC-

VIP Member
Jul 23, 2004
682
48
US
Not sure why but glad you were able to grab your keys! :)

Sent from my DROID RAZR using Tapatalk 2