SAMSUNG MS28 ms28 dvd key

[Diddlesom]

Hello,i was given a 360 with a E65 error so pulled the drive out and went on to hook it up to jungleflasher but my pc would freeze for say 30 seconds then work for 3 or 4 seconds.
So i went to DOS and did a DOSFLASH16,found the drive and R to read the flash and saved to ORIG.bin.
Then DOSFLASH V to verify the key and it failed Sense FF/FF/FF
Back in windows i tried to open the ORIG.bin with jungleflasher and i get:
MD5 hash: xxxxxxxxxxxxxxxxxxxxxxxxxxx
Parse Failed !

I have done this a few times with the same results each time,is the drive bricked or any ways around this ?

I hope someone can help and thanks for your time

 

[Xmarksthesh0t]

why not use Jungleflasher and how did you hook up sata or what?

 

[Diddlesom]

Hi,when i hook the drive upto via 6421 card SATA it makes windows freeze so jungleflasher is out of the question

 

[Xmarksthesh0t]

then you need to send someone like me who has X360usbpro and CK3, or get one mate. even via chipsets are a bit messed compared to usbpro.

 

[Diddlesom]

I have an old X360USB SATA to USB cable but not the new pro not tried the old cable you think it might work ?

 

[Diddlesom]

when i connect the drive with x360usb says driver did not load in windows.
Jungleflasher cant see the drive and the box USBonly is always grayed out

 

[Xmarksthesh0t]

have you got the drivers.

 

[Diddlesom]

i must have or maybe i was just lucky as i flashed a Hitachi with this x360usb cable a couple days ago,when i got into windows i remember it saying the drive pop up and this time was unrecognized

 

[Xmarksthesh0t]

install driver if you need help get team viewer and ill help first hand .

 

[Diddlesom]

The only drivers i can find are for X360USB PRO i do not have the PRO i have the original but i cant find drivers for this and it should work with samsung drive as they are the same age.

---------- Post added at 18:15 ---------- Previous post was at 18:07 ----------

http://www.coolmods.co.uk/catalog/images/x360usb.jpg

That is what i have and apparently there are no drivers for it as its native to windows.

It works as i used it a couple of days ago but with a hitachi but maybe has problems with samsung.

Going back to my OP i cant see why i cant use DODFLASH16 for this as it reads the flash and create's the ORIG.bin for me but cant open it and get my key out which i need to move on.

---------- Post added at 18:19 ---------- Previous post was at 18:15 ----------

I have since found out it is not compatible with samsung drives so back to dosflash for me i guess,dont want to buy a Pro version to find this drive is bricked

 

[Diddlesom]

Just ordered a x360usb Pro im sure it will come in handy even if this drive is dead.
Thanks for your help with this

 

[Xmarksthesh0t]

You need it as you will need the dummy.bin, Good for ordering and supporting this place .
Just ask me when you get it and ill help you 100% dont worry man with Team viewer ill even do it for you lol . These products come with warranty and support, better then some other products like via's etc.

 

[Diddlesom]

hi,i got my x360usb pro and it still wont see this ms28 drive,Its all installed properly as i have tested it with another drive and it found it right away and read the flash in an instant.
Im sure this drive is screwed

 

[Diddlesom]

I put it on my gaming pc and it found the drive and this is the results from reading :


Sending Device ID request to port 0x0000
Manufacturer ID: 0xBF
Device ID: 0xB6
Flash Name: SST(SST39SF020)
Flash Size: 262144 bytes

Getting Status from port 0x0000
Parallel flash found with Status 0x70

Reading Bank 0: ................
Reading Bank 1: ................
Reading Bank 2: ................
Reading Bank 3: ................

Dumped in 10161mS

Samsung Dump file saved to SAM-OFW.bin
Loading firmware from buffer
Parse Failed !

I cant open the file in firmwaretool either

 

[Diddlesom]

well anyone ? does this mean the drive is screwed ?

 

[cab0747]

I put it on my gaming pc and it found the drive and this is the results from reading :


Sending Device ID request to port 0x0000
Manufacturer ID: 0xBF
Device ID: 0xB6
Flash Name: SST(SST39SF020)
Flash Size: 262144 bytes

Getting Status from port 0x0000
Parallel flash found with Status 0x70

Reading Bank 0: ................
Reading Bank 1: ................
Reading Bank 2: ................
Reading Bank 3: ................

Dumped in 10161mS

Samsung Dump file saved to SAM-OFW.bin
Loading firmware from buffer
Parse Failed !

I cant open the file in firmwaretool either

Looks like it dumps fine.... Once it has been dumped, can you close JF, re-open the program, and attempt to load the firmware?

I have NEVER seen this before, so this next comment is just a guess: It looks like there is either an issue with the chip, or the firmware that was originally written to the drive.

Also, I am guessing this is a Xenon so there is no chance it can be RGH'd.

Edit: Is the FW saved to a file? If so, please email it to me, I will see if I can open it up.

 

[BL4K3Y]

Parse failed usually means JungleFlasher can't find the relevant firmware file.

Make sure you are using the latest version and that you also have the latest firmware pack extracted to the firmware directory.