My nand.

S

Soryn

Full Member
Feb 17, 2011
53
0
Hello.

I have a problem I was trying to find my NAND ( I know its Jasper but I dont know if its small or BB block ) so I dumb both of them ( btw I was trying RGH roadnobies ) for find if its small or BB but no result.

So I decide to dumb with J-Runner one time for normal and one time for small block but with both of dumps I get this http://imageshack.us/photo/my-images/845/nand.jpg/

See there are so many Bad Key/KV why ?


And please tell me how I find is its small or BB it really matter ?

Thanks u!

---------- Post added at 01:26 ---------- Previous post was at 01:24 ----------

In Flash Tool Dump only says Jasper 16 mb it doenst show me up small block or BB...

---------- Post added at 01:27 ---------- Previous post was at 01:26 ----------

In J-Runner same 16 mb Jasper...
 
TheRealKTFO

TheRealKTFO

VIP Member
Dec 30, 2010
157
0
Ohio
I don't think you added your CPU Key, that would explain the KV problem I believe...
 
Last edited:
Martin C

Martin C

VIP Member
Jan 10, 2004
35,981
0
Scotland, UK
www.team-xecuter.com
can't you see 'Flash Config' in that screenshot? I can.

You have a 16MB Jasper.

If you cancel out of NANDPro, you need to unplug it from the PC and reconnect it for it to work.
 
S

Soryn

Full Member
Feb 17, 2011
53
0
Lol didnt saw it its 2 AM here :(

I know its 16 mb Jasper but i dont know if its small or BB ?

---------- Post added at 02:01 ---------- Previous post was at 02:00 ----------

In J-Runner when I read NAND its asking me to choose 16 mb and 16 mb small block thats confuse me...

---------- Post added at 02:05 ---------- Previous post was at 02:01 ----------

But the problem with Bad Key/KV from where come ?
 
Utmad

Utmad

VIP Member
Aug 15, 2010
3,304
118
Southampton, UK
It is a 16mb Jasper, a BB is a 256 or 512mb, the 16mb small block is if you want to only read part of a BB.

It says bad kv because you have not got to the point of getting your cpu key yet, until you get your key this is normal.
 
Last edited:
S

Soryn

Full Member
Feb 17, 2011
53
0
I didnt know I need this cable NAND-x to CoolRunner Jtag Cable for program my CR.What I have now is LPT cable wich come with CR bundle.

My friend ask me if I had the schematics from Xecuter NAND-x to CoolRunner Jtag Cable he may make one for me, can i find somewhere that schematic ?

Thanks very much!
 
Martin C

Martin C

VIP Member
Jan 10, 2004
35,981
0
Scotland, UK
www.team-xecuter.com
Soryn said:
I think I have LTP port in my PC now I have to find the tutotial, searching...
Click to expand...
You have a NAND-x. THIS is used for both reading/writing your NAND AND programming the Coolrunner.

You don't need anything else so put away any LPT cables you have. Look at ANY of the NAND-x wired installation diagrams and they'll show you how to install it.

How did you not see the NAND-x Install Guide in the Tutorials section? It's right there in the stickys at the top of the page for NAND-x Support.

Open wide - here comes the choo-choo:

http://team-xecuter.com/forums/showthread.php?t=54423
 
Last edited:
S

Soryn

Full Member
Feb 17, 2011
53
0
Martin all I want to do is to clear my AP 25. challange flag... I have installed NAND-x these two tiny pieces http://www.team-xecuter.com/nandx_pics/install/J1D2_J2B1-1_0526.jpg no JTAG installed because I dont want to JTAG.

---------- Post added at 10:52 ---------- Previous post was at 10:51 ----------

No wait Im wrong, I have installed... wait

---------- Post added at 10:57 ---------- Previous post was at 10:52 ----------

Look I made a photo now only those tiny pieces http://imageshack.us/photo/my-images/515/image0799.jpg/

---------- Post added at 10:58 ---------- Previous post was at 10:57 ----------

Is enough to program my CR and build a new retail MS ?
 
S

Soryn

Full Member
Feb 17, 2011
53
0
Yes thats what im talking about... and I have LTP cable but this seems hard to use then eazy usb, here I have to power CR with CK3i I think ( i have ck3i ) seems pretty complicated...
 
You must log in or register to reply here.