RGH Nand-x Looking for usb interface device

[lucifer]

My Nand-x was working. I am not sure what i have done now its always saying

Looking for usb interface device
Can not continue

I have checked with 3 board which I have RGH before with coolrunner QSB but same thing. I am confident about the solder because all the board are using QSB already RGH working. I am using windows 7 x64 and my nand ARM is v3.

 

[rexdale]

Have u tried the reset button?
Do the boards have the power plug connected to them?
Is it programmed? (prolly)

 

[BoSsLoBbYz]

Is this a console that you have already soldered to the HANA point with.

For some reason when you have the HANA point soldered on and you are trying to read the nand it just doesnt work.

Try restarting your computer also

 

[WestCoastConsoles]

Check to make sure that it is showing up in device manager properly.

 

[lucifer]

I have already reinstall windows. but no luck. driver installation and its showing up in device manager properly. i have tried to flash coolrunner with my nand-x its working. but I can't read/write the nand. is there any way to check my nand-x is ok ? interestingly even if I don't connect nand-x with my console its also saying same thing.

 

[tennisdude516]

I know you said it's not soldering, but every case I have ever seen of this happening, it was either not recognized (which isn't your case it seems) or bad soldering. I thought my soldering was good as well, and I went back and abandoned the QSB, as it is much much easier to see the joints, and PRESTO! Properly reading NAND.

 

[paul.86]

Is this a console that you have already soldered to the HANA point with.

For some reason when you have the HANA point soldered on and you are trying to read the nand it just doesnt work.

Try restarting your computer also

Not entirely true I install all coolrunner and nand x wires before turning on to dump the nand

Sent from my HTC Vision using Tapatalk

 

[lucifer]

I know you said it's not soldering, but every case I have ever seen of this happening, it was either not recognized (which isn't your case it seems) or bad soldering. I thought my soldering was good as well, and I went back and abandoned the QSB, as it is much much easier to see the joints, and PRESTO! Properly reading NAND.

I am sure because I have tried with three motherboard which are already RGH'ed using QSB. I just plugged the nand-x cable. even it was working yesterday with same motherboard.

 

[Martin C]

Have you checked the cable itself?

 

[itchyf1ngaz]

download nandpro3.0...put the downloaded folded in the root of your c:/drive....then when you are using coolshrimps jtag toold go ahead and go to the advance tab then to settings and hit that button that says. install nandx drivers. easy as peesy

 

[jeremy790]

I have one that is doing the same thing. Will program the CR and shows in device manger but no luck. Tried 2 different pc's and 3 vm's and same thing. Tried 3 systems with previous rgh install that I know are working. I had posted a thread and someone had mentioned that is the console got powered up with nand x connected it could damage the nand x. Anyway I just ordered a new one so I will let you know if is indeed the nand x.

 

[lucifer]

I have one that is doing the same thing. Will program the CR and shows in device manger but no luck. Tried 2 different pc's and 3 vm's and same thing. Tried 3 systems with previous rgh install that I know are working. I had posted a thread and someone had mentioned that is the console got powered up with nand x connected it could damage the nand x. Anyway I just ordered a new one so I will let you know if is indeed the nand x.

Well... I think i haver powered up the console when nand-x was connected. when you are expecting the nand-x ? please
let me know the result.. i am waiting

 

[jeremy790]

Will do. It should be here today or tommorow.