ANSWERED Nand-X read error than RROD

J

johnylim

Junior Member
Dec 28, 2013
12
0
TX Product(s) used: NandX
Console Type: Jasper
NAND size: 256
Dashboard version: 2.0.16202
CB version: 6754
Screenshot of NAND details from J-Runner:


J-Runner log:


updflash.bin log (if applicable):
Image of Coolrunner:
Images of close-up soldering to motherboard:


-------------------------------------------------------------------------------------------


Description of problem:
Setting up Nand-X (i'm already done a couple of xbox before) , got many read error and different nand result, i though maybe my Nand-X wire is not good (take some look and refixing them), re-read again, still got same error, remove Nand-x trying to boot and then got RROD 0022 after 28 seconds

Was the console working before you started: Yes



I just want to know, what should i check ? I'm already check the nand chip, no any splashed solder, and use magnifier to find a culprit without any result. What should i do?

thanx all for the help
 
Last edited:
D

davyboy

Full Member
Feb 16, 2013
42
0
Have you have only read nand and not written to it. I would disconnect your reader and wires then see if it boots, 0022 code usually points to gpu fault(reball) did the 2 nand dumps compare ok ? write nand back if compares ok then try boot
 
Last edited:
J

johnylim

Junior Member
Dec 28, 2013
12
0
Martin C said:
If you've not written anything to the console, remove everything you've soldered and try powering it on again.
Click to expand...
I've already done so and already explain it too on template-description above.
If it can boot properly i think i will never ask for help.

The problem is i just tried to read nand, while jrunner gave me many error read and different dump result, i cancelled it, remove Nand-X and then the box not boot properly like before.
 
Last edited:
J

johnylim

Junior Member
Dec 28, 2013
12
0
It's a good suggestions, but i dont know who should i ask to take a look for in my cities haha LOL.

I just bought these second hand xbox, without RGH system, tried it before about only 5 minutes and deal. Then i just want to apply RGH, at first step it already make me dizzy, never happen before.

Mr.Martin, may i ask some suggestion from you ? just want to know what point should i check?
My assumption was these box 0022 problem maybe related to nand read error. Any chance of that ? Thx for the support
 
Martin C

Martin C

VIP Member
Jan 10, 2004
35,981
0
Scotland, UK
www.team-xecuter.com
0022 has nothing to do with you trying to read the NAND unless you've left a mess after removing it.

Can you take pics of everywhere you've soldered to?
 
J

johnylim

Junior Member
Dec 28, 2013
12
0
I'm only soldering to the point where nandx wire should be. Just as seen on picture i've attached above, although that was the second soldering.

I will remove it and take a picture again ASAP

@davyboy, thx, I will go take a look
 
Last edited:
J

johnylim

Junior Member
Dec 28, 2013
12
0
Btw I read in other website that hot glue will conduct electricity. I found one splash covering one of resistor and some point. I will try to remove it and give report for the result
 
Martin C

Martin C

VIP Member
Jan 10, 2004
35,981
0
Scotland, UK
www.team-xecuter.com
Hot glue is not conductive. Not sure why anyone would ever write that.

Have you managed to write anything to the console? If not, your CPU probably needs a reflow/reball.
 
J

johnylim

Junior Member
Dec 28, 2013
12
0
I haven't write anything, just want to read , i'm trying to careful, that's why while jrunner gave some bad block and different nand comparison i decided to recheck, remove nandx wire and powering on then these RROD occurred.

I'm owning 4-5 jasper, some sold and i know all of them still running until now from 2010, never seen Jasper RROD like Falcon did, AFAIK its very rare, am i just unlucky ?:mad:


I think i will send to someone to trying reballing it :(

Thx anyway .


Oh almost forgot, i had another JAsperBB with damaged nand chip, it is really not compatible with Falcon one? because i replace the chip, can write and read but with error and can not powering on.
 
Last edited:
J

johnylim

Junior Member
Dec 28, 2013
12
0
YES, Really only that :(.

Oke, i need one more thing to confirm. I've connecting my nandX to other Xbox and read write properly.

But why only these XBOX always got this ??
----------
Reading Nand
Error: 250 reading block 10
Error: 250 reading block 120
Error: 218 reading block 121
Error: 250 reading block 3D0
Error: 250 reading block 3D8
Error: 210 reading block 3DF
Done!
in 8:09 min:sec

Reading Nand to D:\-=games=-\XBOX RGH\PC APPS\J-Runner\output\nanddump2.bin
Initializing nanddump1.bin..
Jasper 256MB
Reading Nand
Error: 250 reading block 10
Jtag Selected
Nand Initialization Finished
Error: 250 reading block 120
Error: 218 reading block 121
Error: 250 reading block 3D0
Error: 250 reading block 3D8
Error: 210 reading block 3DF
Done!
in 8:07 min:sec


Comparing...Takes a while on big nands
Bad Block ID 0002 Found @ 0x01FF [Offset: 0x41DF000]
Block ID 01FF [Offset: 0x41DF000] remapped to Block ID 0002 [Offset: 0x42000]
Bad Blocks Remapped
Bad Block ID 0002 Found @ 0x01FF [Offset: 0x41DF000]
Block ID 01FF [Offset: 0x41DF000] remapped to Block ID 0002 [Offset: 0x42000]
Bad Blocks Remapped



----------------------



And always gave different nand comparison result. Is it true my NAND SMD chip broken ? and because it broken then it cause RROD ?
 
J

johnylim

Junior Member
Dec 28, 2013
12
0
Just my assumption based on my limited knowledge, and i was ask because i'm not sure :)

So if it only bad block why the result always got different nand ? I dump perfectly on other xbox. So if these box not RROD i think it will still not be able to RGH-ing it because always got different Nand dump ?
 
You must log in or register to reply here.