I was trying to RGH Falcon 16MB....it was having bad block , i repair that....and problem is that nandx stop to work....(sopped at writing ecc) it is in system properties,when i plugged USB cable it is here...but when i try to read , write to NAND i got "looking for usb interface device Can not continue"...So i flashed Nandx again via Flash magic and CK3 cause i was thinking that maybe something got wrong with nand...some strange erase or something....nothing....it is not working (with that 2 mbos) ... Second thing is that i didnt power up console with NANDX plugged like some post says it can happen....After few days and 4 successufl RGH today i tried another MBO but again 16MB and it is Jasper model....i stucked at same position like with that Falcon MBO -at writing ECC file....Nandx working with another consoles but with that 2 -looking for usb-message...cannot read ,write nothing....and i cannot boot freebot...i dont use TX boards cause i just wanted to obtain DVD key im good with soldering and really need some opinion or help with that 2 consoles cause im afraid if 3 MBO :crazy: will be 16mb that i will have same problem...Please help me!
RGH Nandx? or MBO?
- Thread starter Buljo
- Start date
Martin C
VIP Member
I will try Martin but it is strange ,now i work with another console and i assume that i will RGH that console with no problems and with same wires...il be back when im made it...
:rolleyes2: I dont know now anything...This new try was Jasper 256MB and when i started to read with Coolshrimp JTAG tool i got 4-5 bad blocks...tried to read second time-same message(i dont wanna write it anymore)....i used new wires....Martin my mind is blowing in a wind i cannot think anything now...:crazy:
i tried to reinstall Nandx..same thing...in devIce manager at details , device instance id i got USB\VID _FFFF&PID_0004\DEADCODE .....is that normal?
Did you plugged in the power to xbox?
---------- Post added at 20:03 ---------- Previous post was at 20:01 ----------
also, check the brick color, if it's red then disconnect the brick from the power supply and reconnect, you should have a orange light. Never solder anything on the MOBO with the power plugged in, this will cause the red led on the brick.
---------- Post added at 20:03 ---------- Previous post was at 20:01 ----------
also, check the brick color, if it's red then disconnect the brick from the power supply and reconnect, you should have a orange light. Never solder anything on the MOBO with the power plugged in, this will cause the red led on the brick.
I plugged power but normaly i didnt power up console...i tried to reset but nothing i think its a same thing like disconnecting from USB....i will try to resolder again cause i readed alot of bad soldering but ....maybe just maybe i didnt solder good...my wires didnt go to oder side like i saw on some posts ....cannot believe that there is so different things happen from no problem RGH to this....what is temperature of soldering station people....how much do you use? I soldered lots of modchips in my life and i like RGH but this problem i cannot solve for now...i will try tomorrow....and i dont like MS soldering iron.
frostbyt
BANNED
- Sep 18, 2011
- 129
- 0
Mh soldering station runs at 350 and I use flux, not the cheap liquid stuff either I actually use my reballing flux... amtech 
...Nothing but the best when I'm working on customers stuff or units I'll be selling
I'm sure amtech is over doing it but so many other flux's I've used leave a crap residue which I don't like or like to clean off for that matter. Amtech cleans off nice and leaves your solder with a nice shine
I would recheck the wiring as you seem to be unsure of it, but it does also sound like you are having usb issues if it works one time but not the next..
...Nothing but the best when I'm working on customers stuff or units I'll be selling I'm sure amtech is over doing it but so many other flux's I've used leave a crap residue which I don't like or like to clean off for that matter. Amtech cleans off nice and leaves your solder with a nice shine
I would recheck the wiring as you seem to be unsure of it, but it does also sound like you are having usb issues if it works one time but not the next..
400 degrees o.7mm.....liquid flux,but i think that non liquid flux is better...i will try again and ill post results...
On J1D2 i got 0.09V not 1V....
---------- Post added at 02:04 ---------- Previous post was at 01:57 ----------
No,sorry,all points got good indicators...like it should be...http://www.team-xecuter.com/forums/showthread.php?t=77908
---------- Post added at 02:08 ---------- Previous post was at 02:04 ----------
No...it is not good ...mBO under J1D2 is good but up is no good...
---------- Post added at 02:11 ---------- Previous post was at 02:08 ----------
Points 1 and 2 at up side of Mbo lower values
---------- Post added at 02:04 ---------- Previous post was at 01:57 ----------
No,sorry,all points got good indicators...like it should be...http://www.team-xecuter.com/forums/showthread.php?t=77908
---------- Post added at 02:08 ---------- Previous post was at 02:04 ----------
No...it is not good ...mBO under J1D2 is good but up is no good...
---------- Post added at 02:11 ---------- Previous post was at 02:08 ----------
Points 1 and 2 at up side of Mbo lower values
I have removed littl solder from point 1 and 2 and now i got 1V
---------- Post added at 02:25 ---------- Previous post was at 02:25 ----------
Sorry,dont have camera near me right now... now i will try to solder wires again...
---------- Post added at 02:25 ---------- Previous post was at 02:25 ----------
Sorry,dont have camera near me right now... now i will try to solder wires again...
ALl points show good values,but there is again ---no usb message....Im usig JTAG cooshrimo program....dont know what to try now....i will take some pohotos at monday if i dont make it today so...help would be appreciated....