RGH NANDx v3 can not read my NAND

[myst77]

hello
i just got a NAND-X v3

i soldered the QSB on my slim and i can not read NAND

The error in Jrunner is:

Flash Config: 0x00000000
Can not Continue
Can not continue

The soldering is OK, i tested it with a multimeter
i tried it both in WinXP and Win7
The console is plugged but turned off
I tried to reflash the NAND-X v3

What can i do please?

 

[TenthBarley]

I read elsewhere you need to downgrade to v2
"...the V3 code on the NAND-x will ALWAYS return the 'No USB Device' error, regardless. You would need to reflash the NAND-x with V2 code..."
I may be wrong but it's a suggestion!

 

[xXBlaZeXx]

pics of soldering per forum rules buddy

 

[Krafter]

pics of soldering per forum rules buddy

Do this first. This error is generally soldering problem.

 

[myst77]

ok... here are the pics

i used the multimeter and there is continuity between the QSB points and the back of the mainboard

oooh what can i do ?

 

[Martin C]

Have you read my NAND-x guide?

Also, ignore any suggestions of downgrading the NAND-x


Sent from my iPad using Tapatalk HD

 

[jsinger47]

I read elsewhere you need to downgrade to v2
"...the V3 code on the NAND-x will ALWAYS return the 'No USB Device' error, regardless. You would need to reflash the NAND-x with V2 code..."
I may be wrong but it's a suggestion!

What are you smoking?

In the case of a spelling error, I blame Tapatalk.

 

[TilVl]

Had v3 on mine since v3 came out and no problems.

Sent from my SGH-T839 using Tapatalk 2

 

[myst77]

ok solved.
i put more solder on some points and i got 2 same nands!

the problem now is with ECC
i create it and when i press "write ECC" i get many error like:

Error: 000 writing block E
Error: 000 writing block F
Error: 000 writing block 10
Error: 000 writing block 11

etc

Now what can cause that problem?

thanks in advance guys ... i am very nervous about this

 

[Krafter]

May still be soldering. Post your J Runner log.

 

[Statecowboy]

Try unplugging your console and plugging it back in (make sure to not turn it on) and also unplug the nand-x from your pc and plug it back in.

Also, you didn't by chance turn your console on with the nand-x connected did you?

 

[myst77]

thank you
Statecowboy

I unplug&plug and i wrote the ECC

I connected the CR3 Lite on MB

the problem now is with XELL boot
I press the button to turn the console on.
i only hear the "beep" from the inside speaker.
No light in front of Console and the led on CR3 Lite is RED

Now what...
i almost finished but that sucks

PS when i put the switch to PRG and turn on the console the fan starts to work, the green light is constantly ON but no signal on TV

 

[Statecowboy]

thank you
Statecowboy

I unplug&plug and i wrote the ECC

I connected the CR3 Lite on MB

the problem now is with the CPU key
I press the button to turn the console on.
i only hear the "beep" from the inside speaker.
No light in front of Console and the led on CR3 Lite is RED

Now what...
i almost finished but that sucks

So now we need pics of your CR install.

 

[myst77]

ok!

thank you very much for your help!!!

 

[Statecowboy]

Edit: what timing file is you use to program your CR? You did program your CR right?

 

[myst77]

after reading the nand i connected the CR on NANDx and pressed FLASH CR in Jrunner. I did only this

 

[Statecowboy]

was the CR in program mode when you did this? is the CR in normal mode when you're trying to boot?

 

[myst77]

yes it is in normal mode when i boot.
i am almost sure that when i flashed the CR iit was in PRG. By the way it wasn't connected to MB so it was "on air" and i think that the switch doesnt mind in that case

 

[Statecowboy]

To be sure, why dont you reprogram your CR - it won't hurt anything. Make sure you select the correct timing file for you MB. I'm not sure what you mean by "on air", but you need to be in pgoram mode when you program the CR.

 

[myst77]

Thank you again my friend. I will try it tomorrow.

How/where do i choose timing files? I thought i just press "flash coolrunner" in JRunner.

One more thing. When i flashes the switch was to "PHAT" (i forgot it there )
Can this make all that mess?

Sent from my Galaxy Nexus using Tapatalk 2