Need a little guidance please

[stevebentley27]

Need a little guidance please

I have updated my nand x using the tutorial ,then proceeded to install the qsb's (phat ) - for the rgh hack connected all the leads to the qsb's and then to the nand x and tried to get a nand dump but for some reason it wont let me !!!! think ive done something wrong somewhere

Does the coolrunner need to be wired up 1st before i try to read the nand ?
also do i need to program the coolrunner before installing to the console ?
thanks for any help you can offer

 

[Beejeex]

Maybe start here

http://www.team-xecuter.com/forums/showthread.php?t=78885

 

[WNYConsoles]

Make sure the XBOX is plugged into the power supply but not turned on.

 

[stevebentley27]

thanks for the help ive just tried to read my nand and its coming up looking for usb interface and then comes up error
Not sure if its because i have not installed the coolrunner ?
will double check with a multi meter on all my solder points

 

[Rich007]

Odds are its probably soldering related, but reading the rgh roadmap will help no end. If you can't find anything but solder related, then post pics of your install.

Regarding pics please read the stickies thread entitled "pics" in the same forum as the rgh roadmap.

 

[Rich007]

thanks for the help ive just tried to read my nand and its coming up looking for usb interface and then comes up error
Not sure if its because i have not installed the coolrunner ?
will double check with a multi meter on all my solder points

You do NOT need the cool runner installed to be able to read the NAND, please post the exact error message where it says looking for USB interface.
It's probably, no drivers, bad soldering or no power connection to the mobo

 

[stevebentley27]

out of curiosity ive just took my working jtag apart and connected my nand x to it to see if i can get a nand dump from that now when i use nand pro it coming up

looking for usb interface device
can not continue

now i used to be able to read my nand from the jtag

now im thinkig it could be my nand x ?

not quite sure now how to proceed

wuld aprciate any help from here

 

[keil423]

A couple things to check.
First does you computer make the friendly sound when you connect the nandX?
What leds are on on the nand X?
Does the NandX show un properly in your Device manager?
Have you tried Pressing the Reset button for 5 seconds on the NandX while pluged into your computer?
Have you tried both a Different USB cable and/or USB port?

 

[WNYConsoles]

Also, when did you purchase the NANDX and did the box say "Nandpro 3 code" or something similar? You may need to update the NANDX for Nandpro 3 code.

 

[keil423]

Also, when did you purchase the NANDX and did the box say "Nandpro 3 code" or something similar? You may need to update the NANDX for Nandpro 3 code.

No if his nandX was on the old Nandpro 2 then it would say somethings about incompatible arm

 

[stevebentley27]

yes the nand x makes a sound when connected
red and yellow leds are showing on on the nand X
yes the NandX shows up as xecuter nand x in Device manager
yes i have pressed the Reset button for 5 seconds on the NandX while pluged into your computer
tried different usb leads and ports

Seems like since i updated the nand x sumthings gone wrong as before i updated to armv3 i could read my nand on my jtag xenon but now its no longer working .

 

[Sovereign.]

This may not work but mine was giving me the same error and I troubleshooted for hours. Then I finally plugged in my av cable and boom it worked perfect. Some people say it does not matter but that is what happened for mine. Possibly try updating it back to v2 and see if it is still working. That should take out a lot of possibility's.

 

[stevebentley27]

will try that and see if that works and report back the results thanks for all the great advice and tips

---------- Post added at 17:14 ---------- Previous post was at 17:13 ----------

how do i update my nand x back to v2 though ???

 

[stevebentley27]

thanks for the advice that worked perfect
plugged my av lead in clicked read nand whay now just got to double check my soldering on my rgh as ive still got probs reading my nand before installing the coolrunner

 

[Martin C]

Now you post images of your soldering like you were asked to do.

 

[stevebentley27]

can u close this thread as ive managed to rgh my falcon board give up on the zephyr board as it just wudnt let me read my nand found out why as well damaged the std clk point ,might repair it and do a wire install when ive ordered another coolrunner thanks for all the help .