never can't glitch ?

[oveis]

Hi . is it sensible some jaspers glitchabel (like cb 6750) never can't be glitching ? any one have like this ? or just must trying work on them to glitch it ?
I have an jasper 16 mb cb 6750 and seems like he wouldn't be glitch at all . refeus everything like route wiring , add all caps in the world (1nf - 150nf) even adding seris , add cap inline on cpu_Rst and everything you can thinking . should i leave it cause i have no hope any more ?

 

[TilVl]

Does the green light blink when you try?

Sent from my SGH-T839 using Tapatalk

 

[oveis]

yep

 

[marshamods]

I never use caps for 16mb jaspers. Also check the sticky about wiring. Remake a ecc with multibuilder also for good measure and flash that.

 

[oveis]

I trying ten time with other softwares to write ecc and nothing . but my question is : can some jaspers never be glitch ? or it's all about your work ?

 

[TilVl]

Post pics of your install.

Sent from my SGH-T839 using Tapatalk

 

[Dosk3n]

All Jaspers can be glitched so its something thats been done wrong. We need high quality pictures of your install so we can see solder points.

 

[oveis]

thanks for your attention but i have phone camera and it's have not good quality .it's my first RGH, anyway also i checked end of wires with multimeter and it's been ok, so my solder points had no probelm . only thing may be problem is when i want to write ecc, nandpro give me some thing like this on every block " msg_controler_... " i dont remmeber exactly what is error but when i search in google some ppl had my borblem and other said its have no problem also when i want to wrote orig nand it's gave me this error every block but writing nand is ok . maybe is it problem ?
( I DONT HAVE NAND-X I USE MY OLD NAND SPI AND I BUILT THAT TWO YEARS BEFFORE BUT ITS WORK CAREFULLY UNTIL NOW )

 

[TilVl]

What programs have you used to build/write your ecc file?

Sent from my SGH-T839 using Tapatalk

 

[Dosk3n]

Even though your points are connected with a multimeter if its bad soldering, poor quality solder or been heated too much and oxidized etc you may not be getting the required current.

Read this and check all the points: http://www.team-xecuter.com/forums/showthread.php?t=77908

You shouldnt be getting errors when writing.

 

[oveis]

What programs have you used to build/write your ecc file?

Sent from my SGH-T839 using Tapatalk

build multibuilder , bestpig , jtagtool
write nandpro 3.0 , jtagtool

 

[oveis]

I write ecc again to find error . error is : usb_control_msg failed -5

 

[TilVl]

You should just get a nand x. Sure that will solve ur problem.

Sent from my SGH-T839 using Tapatalk

 

[Dosk3n]

Dont know the error but sounds like your home made cable

 

[oveis]

i dont think the problem is my nand spi because i read nand good ( i know write and read technicaly is difference ) but when i write ecc or nand , i try to dump it again and compare them and they have no difference .

---------- Post added at 13:12 ---------- Previous post was at 13:08 ----------

oh guys i forget thanks you for taking your time :smile:

 

[oveis]

i forgot somthing else . when i add 47 nf to A and GND , fan's trying to pulsing every 5 secs and console power off geting delay (slow reset) , somewhere i read fans reset every 5 secs is an sign your coolrunner trying to glitch , so is this true ?

 

[Yorkshire-Modz]

Not sure about the fans resetting but mine sound like they get a little extra surge of power just before the green light blinks.
Pretty sure a Nand-X will solve your problems

 

[oveis]

my nand spi is an oldster . he done many jtags before :eek2::redface:

 

[oveis]

Any advice or help would be grateful