Hi i just bought a mod xbox with the X3 inside with the x3 control panel. It has no bios on it? Im at the main screen the Flashbios3.0.1 is at the top. i Have a bio from the xbins. i have flashbios_x3_303. i can't flash the bios on. i try but maybe i not doing it right someone please help. i read the example but i can't get it to load up?
NEW here and need help?
- Thread starter ShiftyZeus
- Start date
Here is the link for the FlashBios Stuff
[font=verdana, arial, helvetica]www.teamxecuter.com/flashbios
[/font]
[font=verdana, arial, helvetica]www.teamxecuter.com/flashbios
[/font]
flashbios_x3_303.???
Thats the wrong file..
Look for X3 bios in xbins.
make sure rar file is extracted, and flash with correct .bin file for your xbox version.
Thats the wrong file..
Look for X3 bios in xbins.
make sure rar file is extracted, and flash with correct .bin file for your xbox version.
this link is instrutions on winrar.
http://teamxecuter.com/unrar/?CMSSESSID=20e41feec9ad3f12fc47c28b53f495ac
http://teamxecuter.com/unrar/?CMSSESSID=20e41feec9ad3f12fc47c28b53f495ac
ok i done that...now how do you burn it to a cd. and what would be the best way. I have nero 6...
Littlemiss already gave you the link to how to do everything to do with flash bios - cd burning is covered and in the guide they even use NERO
can you follow instructions?
Heres the link one more time:
http://teamxecuter.com/flashbios/
can you follow instructions?
Heres the link one more time:
http://teamxecuter.com/flashbios/
most likely your flash protect switch on the chip or on the external switch bank is still set to Enabled. Check them both!
did you rename the bios to bios.bin and how large a dummy file did you use?
did you rename the bios to bios.bin and how large a dummy file did you use?
i ownly have an external switch on my xbox my chip i look at it and i didnt see a switch. yes i rename it bios.bin it was X3_3294.....and my dummy file is 100mb
you said you have an X3 control panel - the very left hand switch is Flashprotect - make sure it's out and lit in red to make it disabled.ShiftyZeus said:
There is also a master flash protect switch on the X3 chip itself. Make sure that flashprotect switch is also disabled.
have a look at the following link - nearly at the very bottom is a piccy of the flash protect switch on the chip. your chip may not look identical but the switch will be the same
http://teamxecuter.com/x3/tutorials/x3pin16.htm?CMSSESSID=57dea7c0414bb732a618713fa8a8cabb
Last edited:
ok i did that and the bios i have wont load it say
cd-rom label x3_bios
no bios update found..halting
cd-rom label x3_bios
no bios update found..halting
Try flashing via http. It is explained in the link that has been given. The problems you are running into could be from a bad cd or bad burn. I know from expirence that some x-box dvd drives are very particular to the brand of cd or dvd.Don't use memorex they have the most problems.
it's really not that hard! it' all explained for you.
just follow the instructions in the tutorial to the letter and it should all go fine.
just follow the instructions in the tutorial to the letter and it should all go fine.
Obviously you did not read the link that digthebox gave to you...there's no need for a website to flash via http, what you need is a crossover cable to connect your PC to your XBOX...open your Internet Explorer and type 192.168.0.99 in the web browser and if all goes well you will see the Xecuter Flashbios screen on your PC. Browse for the location of your bios and hit Upload & flash. 