new installation problem

[jack323]

hi
hope for some help please i have 1v xbox and have installed x3 everything seems ok as we can enable ,disable, etc and it changes the colour.
when we start the xbox the quick touch it comes up

flash bios 3.0.0
for help visit xecuter web site
hdd .....................
dvd .....................

enable network flashing (highlited )
load bios from hdd (c:\Bios)
load bios from disc
unlock hdd
lock hdd

i have done a disc with the latest bios and booted up with it but still the same resultthe only option we have is network
thanks

 

[HoBoZ]

if you have a disk with the bios on it then select load bios from disc.. the tray will open and put in your disk and let it flash.

if your disk will not work then select enable network flashing and flash.

all these answers are in the tuts. i suggest that you read them.

 

[nunzio738]

try going here first http://www.teamxecuter.com/flashbios/ and read read and more read to find out the answer's
http://home.comcast.net/~x3guide/

 

[jack323]

hi
cannot select any option except the network option

 

[HoBoZ]

are you using the stock m$ controller?
are there any memory cards in the controller, is so take them out.

 

[jack323]

sorry i wasnt using the controller that came with the xbox now we have movement is there a link to where how can i install slayers software on it please as every time i start the box i have the same the start up screen flashbios 3.0.0 up and not sure how to go further
thanks

 

[PhatheadWRX]

did you flash it with flashbios? or X3 1959? what bios did you put on your disk?

You obviously put flashbios on the disk and re-flashed it with flashbios.
You have to flash the chip with 1959 (either put IT on a disk or network) before you can install slayers

 

[jack323]

can u give me the link for that bios as i cant see it anywhere

 

[PhatheadWRX]

you have to find it in the "usual places"... modified microsoft bioses are illegal hence no link.

If you still do not know search for "usual palces" at www.xbox-scene.com

 

[jack323]

Ok thanks now the bios has been updated to3.0.3
still having props ,cant reconise disc to update dash
thanks

 

[jack323]

how can i install slayers software on it please as every time it starts
there is no option i have 3.0.3 instaled.
Thanks

 

[sidewinder007z]

Are we following you right?? Did you flash on of your eight banks with Flashbios 3.0.3? That should be flashed onto your backup rom.

X3 Bios 1959 should be flashed into one of your 1meg bios banks in order to get anywhere near a dash.

 

[jack323]

Tanks for all your help
i did flash it and it said bios 3.0.3
now it sais bios 3.o.1 how can it change and still no option to install new softweare on a new hard drive 120g

 

[jack323]

Need Help

x3 has been fitted works ok i think, now i have sett the first two switshes on and other three off made a disk and flashed it with 3.0.3 goes to the end of the flashing and the xbox switshes off.

when i start it up the displey sais flashbios 3.0.3 and that is it,exept if i hold the power buton in it fires up as normal with no mod.
thanks

 

[jack323]

flashbios? or X3 1959 is the one i have used.
Thanks help

 

[jack323]

I have notesed that if the hard drive is not locked it gives me call for
service, dos this meen that the mod chip is not working?

Thanks in advance

 

[shortyno69]

sorry i cant help u but supprised that nobody has come to your aid with some advice best of luck

 

[jack323]

Thanks Shorty

 

[k-dogg]

LITE-ON 83850C BRICKED?

OK, i have flashed many drives b4 but have got stuck at this one.... using the new version of jungle flasher with my 83850c drive and did the dummy file thing then loaded LT firmware and saved to file...... then went to erase the drive cycle powered the drive and got an error message (cant remember what it was) now the drive is dead... JF will not detect the drive anymore so i cannot put into vendor mode and it will not eject at all....please help


cheers jay

 

[ReMix]

Re: LITE-ON 83850C BRICKED?

if you had read the jungleflasher tutorial, you would have seen that your drive is not bricked, it is locked

just send device intro to the port that the drive is connected to

then power cycle the drive