RGH No Dash Selected

[Sfeth]

Hi, I have done the RGH 1.2 mod on my Falcon dash 16537 and I got Xell boot got my CPU key but when I tried to create Xbuild Image it says No dash selected. I tried to mannualy put it with add dash and it doesent select my dash it just selects the "....." dots that are showing there in the box.Hence I cannot write the nand. Anyone knows how to fix this .. thx

 

[playingmax]

save ur nand back ups and delete the jrunner u have installed. download this one jrunner with 17511

 

[jligg]

You also can download xebuildgui and it has all the dash boards with it, then copy the ones you want from xebuild to jrunner

 

[Sfeth]

save ur nand back ups and delete the jrunner u have installed. download this one jrunner with 17511

I did that and wrote the nand with the updflash.bin and now my console doesent want to boot I checked the wiring and everything seems to be good but no boot ...anyone knows what could be the problem?

 

[GeekHeat]

I did that and wrote the nand with the updflash.bin and now my console doesent want to boot I checked the wiring and everything seems to be good but no boot ...anyone knows what could be the problem?

Does it still boot xell?

 

[Sfeth]

Does it still boot xell?

No, it doesent boot Xell anymore I let it sit for like 5 min. and just black screen nothing else.

 

[GeekHeat]

No, it doesent boot Xell anymore I let it sit for like 5 min. and just black screen nothing else.

Create and write ecc again and see if it boots xell.
If not then need to see pics of install and jrunner log

 

[jligg]

Did you make sure to select the rgh2 bullet when you built your image?

 

[Sfeth]

Did you make sure to select the rgh2 bullet when you built your image?

Yes I did.

 

[Sfeth]

T

 

[playingmax]

ur Pll and Rst should be as short as possible.

 

[playingmax]

and are you tring different timing files

 

[Sfeth]

and are you tring different timing files

Yeah, as I said it bootet into xell and I got the CPU key the boot time was almost insta like 1,2 seconds boot time , so I dont think the wire are the problem since it booted? Now after I saw that the console isn't booting I did tried a different timing on CR but no result. Also when I had it booted the first time I had the motherboard sit on the couch it wasant in its case, so I keept it like that for about 5 minutes until I wrote the CPU key and after that it RROD and I found that the CPU_RST point was not to well soldered there so it had come off I resolder the wire back and since then I can't boot it no matter what.

 

[playingmax]

it could be u damaged the rst point. write original nand back to console and see if it boots. if not u will need to fix the trace.

 

[Sfeth]

it could be u damaged the rst point. write original nand back to console and see if it boots. if not u will need to fix the trace.

Do I need to remove the CR fromthe board?

 

[playingmax]

after writing nand remove red wire from CR. and see if console boots. report back.

 

[Sfeth]

after writing nand remove red wire from CR. and see if console boots. report back.

umm... yeah ok but how do I write the orig. nand back?

 

[gavin_darkglide]

Load the original dump in J-runner, and hit write nand. It is fairly straight forward, unless you erased it on accident, in which case you are screwed.

 

[Sfeth]

Load the original dump in J-runner, and hit write nand. It is fairly straight forward, unless you erased it on accident, in which case you are screwed.

No i didnt delete the nand dumps , do I need to select a dash version in the box while i'm writing the orig. back?

 

[gavin_darkglide]

no, that is only for creating a nand image.