RGH No Dash Selected

[Sfeth]

no, that is only for creating a nand image.

Do I need to selet retail in the box or just leave it to Jtag? Also if I select retail what should I write in the CB box next to it?

 

[GeekHeat]

Do I need to selet retail in the box or just leave it to Jtag? Also if I select retail what should I write in the CB box next to it?

u are over complicating things.
Just add your original nanddump1 to load source, then press write nand.
U don't need to change anything else.
U can then switch coolrunner to program, which will disable the chip.
Then boot up Xbox to see if it boots to retail.

 

[Sfeth]

Ok so I writed the orig. nand back and it booted.. thank god. Do i need to do the whole process again of the Rgh 1.2 ?

 

[gavin_darkglide]

if you have the cpu key, you can make the nand image.

 

[Sfeth]

Ok so I put the CPU key there and it says CPU is Correct I create image and wrote it to the nand with dash 17511 selected and the console doesent want to boot into dash

 

[john mathews]

he is not using a tx chip/n your soldering and wires need to be fixed

 

[Sfeth]

Are you sure?

 

[gavin_darkglide]

Dash timing and xell timing on the chip can be different. I have had consoles that would boot xell first glitch, but not xebuild image, until changing timing file on the coolrunner.

 

[playingmax]

and do u have anything bridged on the CR?

 

[Sfeth]

and do u have anything bridged on the CR?

NO, I haven't messed with the jumper setting I'm using CR rev. C

 

[playingmax]

try removing the JP resistor on CR

 

[GeekHeat]

I've done 100s of falcons with rgh1.2 with no issues at all.
Everyone has timing file 19.( Always using onboard clk point) I've never had to change timing file.
Always left the chip as default.

 

[Sfeth]

I've done 100s of falcons with rgh1.2 with no issues at all.
Everyone has timing file 19.( Always using onboard clk point) I've never had to change timing file.
Always left the chip as default.

what do you mean by ( Always using onboard clk point)?

 

[GeekHeat]

what do you mean by ( Always using onboard clk point)?

The B point on the chip. Which u have to use on a rev c.
U are using point B so forget about it.

U need to trim your wires down. So no excess wire showing. Use timing file 19. If installed correctly it shud boot xell on first or second glitch.

 

[Sfeth]

I got it to boot by reprograming the chip with another timing file, but the XeX menu doesen't show on the hard disk can you point me a good tutorial about XeX menu and other cool stuff?

 

[playingmax]

I got it to boot by reprograming the chip with another timing file, but the XeX menu doesen't show on the hard disk can you point me a good tutorial about XeX menu and other cool stuff?

we cant keep spoon feeding you. use the search. also google is ur friend.

 

[Sfeth]

Yeah sorry I know sometimes I'm lazy..thanks

 

[rick48235]

Yeah sorry I know sometimes I'm lazy..thanks

so do you think that Gives you a pass NOT

 

[gavin_darkglide]

put 2 copies of aurora on a usb drive. create a launch.ini that defaults to 1 of the copys, and a launch.ini that points to the version you are going to put on the HDD. copy the second copy of aurora and the hdd launch.ini to the hdd. reboot the console. if it doesnt boot into aurora, make sure you included dashlaunch when you created your image. if you didnt, flash a new image with dashlaunch included. as for xex menu, if you want it, copy the 0000000000.... folder to content dir on hdd.

 

[Sfeth]

Another quick question ,I have a wireles controler that is not from this console and I can't get it to work with this console any ideea how can I make it to work on this console?