Martin C
VIP Member
Probably no point in doing anything else without a multimeter. You might end up causing more harm than good.
ANSWERED No green flashing light
- Thread starter TH3D3C0Y
- Start date
Martin C
VIP Member
Ill go through a step by step just in case something is missing.....So I plug in power,front board and video cable.I take my controller plug it in and turn on console. The light on the front board just blinks green(the one in the middle),the controller never sets to first person,no screen,and no blinking green light from the CR.
Martin C
VIP Member
So write back the first 50 blocks of the NAND (nandpro usb: -w16 nanddump.bin 0 50) and set the CR to PRG. It should boot.
I did that and the green light in mid still stays blinking....and now I'm back to a stock Xbox? Is there something I'm missing?Was that the point to re-write the first 50 blocks and set the CR to PRG?
Martin C
VIP Member
Yes, you should be at stock now. As per my roadmap for noob thread, this is what everyone should do before writing ECC as it should work.
Ah...I was following http://team-xecuter.com/forums/showthread.php?t=76193 thread and everything was perfect until I had to boot into Xell and it just hung up. Ive been stuck at that point for almost a day and a half.Let's try your noobie road map.
Martin C
VIP Member
It's too late now either way as you've already written to the NAND.
However if your NAND Dump was good, it should boot up.
Try flashing the full 16MB back instead of just the first 50 blocks.
However if your NAND Dump was good, it should boot up.
Try flashing the full 16MB back instead of just the first 50 blocks.
I'm confused now.....so im basically gunna take my orginal nand and put it fully back on ? This is my first time using nandpro/nand-x and doing RGH...Been studying for a couple of weeks now but still not 100%...Please be easy on me if at some point I brain fart and seem like a Handicap-able.
Martin C
VIP Member
Yes - if things stop working (as they are now), we want to 'back out' everything we've done.
Start with writing the stock NAND back.
If it still won't boot, desolder each wire one at a time and try booting. Hopefully it boots at some point. If not, you've damaged something in the process or done something outwith normal procedure.
Start with writing the stock NAND back.
If it still won't boot, desolder each wire one at a time and try booting. Hopefully it boots at some point. If not, you've damaged something in the process or done something outwith normal procedure.
It boots just fine when you told me to write the first 50 blocks and the CR is set to program.How do I revert back to stock?Is it NandPro usb: -w16 Nanddump.bin?
Last edited:
Martin C
VIP Member
So no need to flash the whole thing back then
So now try to boot with the CR set to NOR.
When I boot it with CR set to norm it doesn't boot.I get a solid red light on the front mid of the board.
Martin C
VIP Member
so PRG works but NOR doesn't?
In which case, it could be an issue with the CR wiring. At worst, the console should try to boot and have a flashing green light on the CR.
In which case, it could be an issue with the CR wiring. At worst, the console should try to boot and have a flashing green light on the CR.
So this is where I'm at. When I boot with the CR on PROG there are no lights on CR and the Xbox boots but the mid light on front keeps blinking.When I boot with CR set on NORM all get is the red light from the CR no blinking green and the front mid light is solid red as well.
Martin C
VIP Member
If your DVD drive is not connected, the light will blink on the front. This is normal.
So the light which was blinking before is now just red?
Post a pic of your CR install please.
Martin C
VIP Member
were you getting a solid red light before you repositioned the 3.3v?
take a new pic with the wire moved.
take a new pic with the wire moved.
