Hi guys , i installed Demon on Corona on 16M nand version, Demon has blue light on external switch, i read nand from retail and wrote back to Demon Nand with Glith nand 16537 , i boot the console on Retail and its fine , i boot the console with Demon but Coolrunner 3 Lite green ligth doensnt blink or turn on , i tried 2 different CR3 Lite , same results , triple checked my connections same result , CR3 Lite doenst glitch , any inputs please would be appreciated
FIXED no green light on CR3 Lite
- Thread starter stanleycup
- Start date
- Status
BL4K3Y
VIP Member
Have you connected the ribbon cable from the CR3 Lite to the DemoN?
Is the CR3 programmed with an Corona_EN timing file?
Is the CR3 programmed with an Corona_EN timing file?
Last edited:
ya the ribbon is connected , cause when i choose program CR in J-Runner , i select Corona timing file 3-2 and i click on Demon Installed in the box , and then when i click Program CR , i see the green light of the CR programming and it says sending XSVF files to Demon in the J-Runner Log and after it says Done !!
BL4K3Y
VIP Member
TX Product(s) used: Demon/Coolrunner 3 Lite
Console Type: Corona
NAND size: 16MB
Dashboard version: 2.0.16547
CB version:
Screenshot of NAND details from J-Runner:
J-Runner log:
updflash.bin log (if applicable):
Image of Coolrunner:
Images of close-up soldering to motherboard:
(attach images to your post)
Description of problem: Coolrunner 3 Lite not Glitching no Green light blinking , tried 2 different ones
Was the console working before you started: Y and still is working on Retail Nand
Console Type: Corona
NAND size: 16MB
Dashboard version: 2.0.16547
CB version:
Screenshot of NAND details from J-Runner:
J-Runner log:
updflash.bin log (if applicable):
Image of Coolrunner:
Images of close-up soldering to motherboard:
(attach images to your post)
Description of problem: Coolrunner 3 Lite not Glitching no Green light blinking , tried 2 different ones
Was the console working before you started: Y and still is working on Retail Nand
BL4K3Y
VIP Member
Erase the DemoN a couple of times before writing anything to it.
Once you have done that, build your glitch image with "noremap" enabled and use the DemoN/Fusion Write option to write the image.
Once you have done that, build your glitch image with "noremap" enabled and use the DemoN/Fusion Write option to write the image.
thanks for your input , i did what u suggested , i erase the Demon like 20 times in a row , built my image with noremap enabled and i used the Demon/Fusion write option to write to the Demon , same result , i simply get no green light on CR3 Lite, after that i read the Nand from the Demon just for curiosity and i had this
Hardware : Demon Slim
Firmware : 1.4
Flash ID : 0x73AD Hynix (16MiB - Small block)
Flash Size : 0x400 blocks of 0x4200 bytes
Invalid Blocks : 0xD3 0xED 0x1D3
Reading Nand
Done!
in 0:20 min:sec
Hardware : Demon Slim
Firmware : 1.4
Flash ID : 0x73AD Hynix (16MiB - Small block)
Flash Size : 0x400 blocks of 0x4200 bytes
Invalid Blocks : 0xD3 0xED 0x1D3
Reading Nand
Done!
in 0:20 min:sec
BL4K3Y
VIP Member
Are you 100% sure the console has full POST?
You said the board was a Corona in the OP, but you didn't tell us which version.
You said the board was a Corona in the OP, but you didn't tell us which version.
thanks a million , thing is that this is my personal console that i flashed with an LTU2 Board 1175 Liteon Drive like 3 months ago so i already had the nand along with the cpu key stored in the computer since 3 months, so when i tried to glitch with Demon/Coolrunner i never paid attention to the post out since i already had the cpu key , now that you mentionned it , i removed the Clamp underneath the board to realize that you solved my issue , many thanks for the multiple replies quickly , i really appreciate it !! , i put the timing files 5-2 for the the xsvf timing files and it boots in 10-15 seconds all the time , many thanks again BL3K3Y , thread closed....
- Status