No xell even after full boot R-JTAG

[Nicpoe]

Same Problem here with 16mb Jasper. Full boot with Rater but no xell, no video. Disconnected JR Programmer, it stops glitching, but no video and no ROD.

Here's the Log:

Phat Selected
Version: 10
Power Up
Waiting for POST to change
Post 40 - Entrypoint of CD reached 
Post C0 
Post E0 
Post F0 - Panic - VERIFY_OFFSET_CB_B 
Post F4 
Post FC 
Post FE 
Post FD 
Post F5 
Post F4 
Post F0 - Panic - VERIFY_OFFSET_CB_B 
Post E0 
Post A0 - Panic - VERIFY_SECOTP_6 
Post 80 
Post 40 - Entrypoint of CD reached 
Post C0 
Post E0 
Post F0 - Panic - VERIFY_OFFSET_CB_B 
Post F4 
Post FC 
Post 1B - RC4_DECRYPT 
Post 1C - SHA_COMPUTE 
Post 1D - SIG_VERIFY 
Post 1E - BRANCH 
Post 20 - CB entry point reached 
Post 21 - INIT_SECOTP 
Post A0 - Panic - VERIFY_SECOTP_6 
Post FD 
Post F8 
Post F8 
Post F8 
Post F8 
Post F8 
Post F9 
Post F8 
Post F8 
Post F8 
Post F8 
Post F8 
Post F8 
Post F8 
Post 10 - Payload/1BL started 
Post 11 - FSB_CONFIG_PHY_CONTROL 
Post 12 - FSB_CONFIG_RX_STATE 
Post 13 - FSB_CONFIG_TX_STATE 
Post 14 - FSB_CONFIG_TX_CREDITS 
Post 15 - FETCH_OFFSET 
Post 16 - FETCH_HEADER 
Post 17 - VERIFY_HEADER 
Post 18 - FETCH_CONTENTS 
Post 19 - HMACSHA_COMPUTE 
Post 1A - RC4_INITIALIZE 
Post 1B - RC4_DECRYPT 
Post 1C - SHA_COMPUTE 
Post 1D - SIG_VERIFY 
Post 1E - BRANCH 
Post 20 - CB entry point reached 
Post 21 - INIT_SECOTP 
Post 22 - INIT_SECENG 
Post 2F - RELOCATE 
Post 2E - HWINIT 
Post 33 - FETCH_CONTENTS_4BL_CD 
Post 34 - HMACSHA_COMPUTE_4BL_CD 
Post 35 - RC4_INITIALIZE_4BL_CD 
Post 36 - RC4_DECRYPT_4BL_CD 
Post 37 - SHA_COMPUTE_4BL_CD 
Post 3A - BRANCH 
Post 40 - Entrypoint of CD reached 
Post 43 - VERIFY_HEADER 
Post 44 - FETCH_CONTENTS 
Post 45 - HMACSHA_COMPUTE 
Post 46 - RC4_INITIALIZE 
Post 47 - RC4_DECRYPT 
Post 48 - SHA_COMPUTE 
Post 4B - LZX_EXPAND 
Post 4E - FETCH_OFFSET_6BL_CF 
Post 4F - VERIFY_OFFSET_6BL_CF 
Post 50 - LOAD_UPDATE_1 
Post 52 - BRANCH 
Post 58 - INIT_HYPERVISOR 
Post 59 - INIT_SOC_MMIO 
Post 5A - INIT_XEX_TRAINING 
Post 61 - INIT_HAL_PHASE_0 
Post 63 - INIT_KERNEL_DEBUGGER 
Post 64 - INIT_MEMORY_MANAGER 
Post 65 - INIT_STACKS 
Post 66 - INIT_OBJECT_SYSTEM 
Post 67 - INIT_PHASE1_THREAD 
Post 68 - Started phase 1 Initialization + INIT_PROCESSORS 
Post 69 - INIT_KEY_VAULT 
Post 6A - INIT_HAL_PHASE_1 
Post 6B - INIT_SFC_DRIVER 
Post 6C - INIT_SECURITY 
Post 6D - INIT_KEY_EX_VAULT 
Post 6E - INIT_SETTINGS 
Post 6F - INIT_POWER_MODE 
Post 70 - INIT_VIDEO_DRIVER 
Post 71 - INIT_AUDIO_DRIVER 
Post 73 - INIT_SATA_DRIVER 
Post 76 - INIT_SYSTEM_ROOT 
Post 77 - INIT_OTHER_DRIVERS 
Post 78 - INIT_STFS_DRIVER 
Post 79 - LOAD_XAM 
Shutdown

 

[XMonsterModsX]

Write back the original nand and remove 5v from rjtag and see if it still boots

Sent from my GT-I9500 using Tapatalk 2

 

[Nicpoe]

yes, does boot fine.

 

[hersheys247]

Fill out template then

Sent from my Brain Tumor causing device using Tapatalk 2

 

[Taijigamer2]

Please post jrunner log and pics of soldering (Rjtag, jtag qsbs).

 

[Nicpoe]

so i flash the original image and it works fine. r-jtag (this time without aud_clamp) loads no xell (stops glitching, but no ROL).

===================================================
Freitag, 25. Oktober 2013 08:05:24

J-Runner v0.3 Beta (2) Started


WARNING! - Your selected working directory already contains files!
You can view these files by using 'Show Working Folder' Button


Checking Files
Finished Checking Files
Initializing nanddump1.bin..
Jasper 16MB
Jtag Selected
Nand Initialization Finished
Version: 03
Flash Config: 0x00023010
Writing Nand
nanddump1.bin
Done!
in 1:55 min:sec

R-Jtag Selected
Patching Jasper version 2.3 SMC at offset 0x12BA
XeLL file created Successfully jasper.bin
Version: 03
Flash Config: 0x00023010
Writing Nand
jasper.bin
Done!
in 0:09 min:sec

 

[Taijigamer2]

Not sure if your pic is recent but your Jtag qsb is turned off. Also, a couple of points on the right of the chip could do with flux and reflow. Have u tried AUD_clamp option, it works very well for jaspers. Good luck.

 

[Nicpoe]

i've tried everything already. first aud_clamp option and switch on, but it boots no xell.

***UPDATE***

So i soldered everything again. And it works!!! I've never thought this could be the Problem.

 

[nofeloniesyet]

i've tried everything already. first aud_clamp option and switch on, but it boots no xell.

***UPDATE***

So i soldered everything again. And it works!!! I've never thought this could be the Problem.

the cold hard fact here is the soldering is about 90% accountable for problems with these things,hell even us pro's miss something here and there from time to time.glad ya got it going in the end