no xell

[stanleycup]

Hi so , Falcon on 16203 , ordered the starter kit , soldered the 2 QSB's underneath board and wired E,F,5V and ground on top of board , for CPU RESET i tried both underneath the board and the alternate one on top of the board, got my 2 nands with Nand-X verified and all, the i created ECC for Dash above 14719 for my Dash 16203 , when i turn the console to get XELL loaded i see the green Debug light flashing every 5 seconds on the R-JTAG but it keeps on blinking even after 5 mins for both CPU Reset points that i tried , i then reflashed console to Stock Nand just to make sure if it was still booting and Yes it's booting just fine on retail nand, i also tried the DIP 3,4,5 one at a time accompanied with Dip 7 ON for Falcon Boards and still NO GO!! i also soldered the AUD_CLAMP whit 1-3jumped and the 2 way swith at ON, any suggestions please, appreciate it ( i didnt solder K point , i have a Nand-X dont have a j-runner programmer for rater )

 

[BL4K3Y]

Complete this template please.

 

[briggs01]

maybe there should be a sticky , titled , things to try if your r-jtag doesnt work , but on the other hand if they cant read instructions they arnt going to read that are they

 

[SoulReaper223]

u need to solder k in order for u to use post rater which will show u all the issues such as soldering and dips. you can also try some other voltage setting

 

[Oggy]

No you don't need to solder K in. He also stated he can't use RATER anyway as he has a nandx not JRP.

 

[blasler]

i have give up to do RGH or R-JTAG on Fat xbox, 3 xbox xwith 0022 error without no reason was to much for me.... xbox Slim ftw

 

[Martin C]

i have give up to do RGH or R-JTAG on Fat xbox, 3 xbox xwith 0022 error without no reason was to much for me.... xbox Slim ftw

As with all mods, R-JTAG requires a level of understanding of electronics and process, which you obviously lack.

 

[xzanox]

Where were his pictures? Did I miss on them?

 

[gizmo613]

sounds like you flashed the rgx ecc files instead. not sure that would work with the rjtag. you need to check off the rjtag box and audclamp box inside of jrunner. then create xell reloaded.

 

[JohnWestBear]

sounds like you flashed the rgx ecc files instead. not sure that would work with the rjtag. you need to check off the rjtag box and audclamp box inside of jrunner. then create xell reloaded.

Shouldn't be flashing any files to the RJTAG board full stop.

Where did it say this?

To OP - Fill in the template and get up some pictures so we can see whats going on. How long is it taking to get to 0022?

 

[stanleycup]

i just created a regular ECC file by the from the DownMenu Advance/Write ECC for above 14719. in the J-Runner software the Dot was clicked under glitch by default so for Creating the ECC for Xell Reloaded my R-JTAG was unchecked

 

[RF1911]

:facepalm:

 

[DreamZ]

What guide are you following? Lol
Are you just guessing the rjtag process?

 

[Taijigamer2]

Oh dear. Have you read the R-jtag official tutorial? It's got everything you need step by step, including j-runner settings. Good luck.

 

[stanleycup]

Oh dear. Have you read the R-jtag official tutorial? It's got everything you need step by step, including j-runner settings. Good luck.

Ya i read the Sticky for the tutorial and installation and fine tuning of R-JTAG but as far as the setting in software j-runner there is no mention of it , just show me where you found it cause i havent found it anywhere

 

[Taijigamer2]

Ya i read the Sticky for the tutorial and installation and fine tuning of R-JTAG but as far as the setting in software j-runner there is no mention of it , just show me where you found it cause i havent found it anywhere

Basic J-Runner Instructions

There are for more indepth guides to using J-Runner however is as a simple breakdown of the steps required for the new R-JTAG option:

Note: Minimum dashboard version required is 15574.

1. Read NAND x 2 (compare)
2. Tick R-JTAG check box
3. Select AUD_CLAMP On or OFF depending on JTAG QSB installation
4. Create xell reloaded
5. Write xell reloaded
6. Boot to xell, get cpu key
7. Create JTAG image of newest dash version (ensure R-JTAG is checked)
8. Write nand
9. Use rater to fine tune boot times

It's at the bottom of the guide. Also check out the jrunner PDF. Just start from scratch with a stock NAND dump. Good luck.

 

[stanleycup]

---

[/B]
[/B][/B]It's at the bottom of the guide. Also check out the jrunner PDF. Just start from scratch with a stock NAND dump. Good luck.

Thank u , much appreciated

 

[xzanox]

Let us know if it worked or not.