** Official JTAG Tool Thread **

[J2G]

In case anyone gets this error I found out the problem. AVGIDSAgent is locking up the CMD.bat for some reason, yet to find a way of stopping this from happening though without having to disable AVG.

Cheers
Mark

I was getting some errors but not the same as yours coolshrimp had this posted on his site so i used it and it fixed the problem don't know if it will fix yours but you could try run it....

Replace Jtagtool.exe in jtag install folder with this one let me know how it goes..
should say 2.76 when u replace it..

try a few time openning and closing and recreating..
make sure it work 100% if so ill release it..

http://www.megaupload.com/?d=D2MX0W7L

__________________
Coolshrimp Modz & Repair
Brampton, ON
coolshrimp.co.cc

 

[coolshrimp]

Iv repacked it with 2.76 Update Now...

 

[stich86]

Iv repacked it with 2.76 Update Now...

hi coolshrimp,

just a question..

if in "Advanced Option" i select "AUD_Clamp/Tray_Open" as alternative SMC poit, this only works with Xell? Or also with the Xellous?

I just want to flash the FreeBoot via Xellous

thanks!

 

[coolshrimp]

The SMC options work on them all (XELL,XELLOUS,FREEBOOT)

 

[stich86]

perfect..
so I can flash Xellous, get the CPU key and write NAND directly from Xellous (with FreeBOOT patched)

thanks!

 

[coolshrimp]

yup..

 

[awill72]

Re: Possible Bug

ftcskater, Did you ever find out why you were getting the JIT Debugging error. I've been searching everywhere and can't find a fix for this. Coolshrimp what can I do to fix this. I'm running XP Pro and it is not allowing me to generate freeboot

 

[peapea]

I jtag Jasper 512MB and got 0022 after flashing Xell
I have already dumped nand 3 time and all are identical and no bad block at all.
I also check all the wire, everything looks great.
Then I decided to flash original nand and unwire all, it still 0022 even with the original nand. Any idea? Please help.

 

[sick360mods]

E10: Unconfirmed: CPU error, generally caused by a poor connection to the mainboard (cold solder joints/bridged solder joints). This can also be triggered by an error with the TSOP.

 

[peapea]

I did turn on before doing jtag. I booted fine.

 

[marshamods]

prehaps you might have bumped something off the board?

 

[peapea]

Actually, before this console. My friend sent Jasper 256MB to me to fix the same problem(0022 after flashing Xell in Jtagtoll 2.76)
I couldn't fix it, even reflash its original nand. So this is the second board that I have this problem.
I think may be, the Xell in this version cause 0022 in JasperBB.

 

[Tulazan]

Hello,

Could you tell me if the USB JtagNT will work with this software as I seem to be having problems.

I have a USB JtagNT connected to a solderless Jasper Jtag adaptor. The software that came with the JtagNT has dumped the NAND fine. I have dumped it five times and all match.

Jtag tool can read the NAND dumps details and also reports the NAND as being from a Jasper 512 with dash 7363 and CB 6763. But if I try and use Jtag toll to read the NAND or install Xell to get the CPU key it fails to see the USB JtagNT is connected.

This will be my first adventure into the 360 SMC/Jtag arena. I am looking forward to moving onward and upward! Any help will be received with thanks!

HDMI Arcade Jasper 512
Dash 7363
CB 6723

 

[iloveme28]

I did turn on before doing jtag. I booted fine.

if you are using cool shrimps tool the smc's for all jasper are wrong

For flashing over xell using nand pro and dont use the smc's that come with coolshrimps tool

 

[manwithoutname]

Try using nandpro on it's own to write the NAND or xell image to your console. the command you need to use is 'nandpro usb: -w512 filename'

 

[coolshrimp]

if you are using cool shrimps tool the smc's for all jasper are wrong

For flashing over xell using nand pro and dont use the smc's that come with coolshrimps tool

they should be fixed?
are you sure?
if so can you send me the correct ones and ill put them in..

 

[Martin C]

they should be fixed?
are you sure?
if so can you send me the correct ones and ill put them in..

Yep, he's sure

I don't get jaspers all that often but will try and sort something out soon.




Sent from my iPhone using Tapatalk.

 

[coolshrimp]

the smc for only xell are bad
or the ones for freeboot also?

 

[Martin C]

Not sure as I only got as far as trying to write XeLL and found it wouldn't boot. I compared smc files in the app directory and the jasper, falcon and zephyr files matched. I would therefore suspect that they are both wrong for jasper consoles.


Sent from my iPhone using Tapatalk.

 

[RedFarmer]

I hope i'm not hijacking here but my problem might be related to the thread.

What would happen if the SMC is wrong and then flashed Xell and Freebot?

I have this Xenon (which i have a couple of threads about already) which always freezes after about 1 min. I believe it to be a RROD side-effect but is there a slight chance it could be a SMC problem? I used JTAG-tool.