OFFICIAL SX OS v2.6 BETA Discussion
- Thread starter Xecuter
- Start date
- Status
Boot emunand and follow this tut
How to Update Firmware OFFLINE - Nintendo Switch with ChoiDujourNX
How to Update Firmware OFFLINE - Nintendo Switch with ChoiDujourNX This guide will walk you through updating the system firmware of a Nintendo Switch Console without going online. You are solely responsible for anything you do to your switch. Make sure your battery is at 100% charge before you...
team-xecuter.com
I just want to say THANK YOU to the devs and the staff of the forum.
Also, where's the atmos sept splash screen? kinda disappointed 'cause the trolls promised it would've been there ?
Also, where's the atmos sept splash screen? kinda disappointed 'cause the trolls promised it would've been there ?
JJTapia19
Full Member
I'm getting a black screen after trying to boot my 6.2 emunand located on sd card files. I didn't even got to update it to 7.0.1. It was working fine on 2.5.3 
Try redownload the boot file and replace it on your SDI'm getting a black screen after trying to boot my 6.2 emunand located on sd card files. I didn't even got to update it to 7.0.1. It was working fine on 2.5.3
JJTapia19
Full Member
I managed to boot my 6.2 emunand located on my fat32 files on sd but the boot rate is small. It boots like one time out of 4 trys. I'll update now to 7.0.1 to see if it's more stable there.
bkintanar
Noob Account
So I got a switch on 5.1 just restored the sys nand to a clean one. Should I update through official servers to play online with official games?. Ofc emunand is currently still safe on 6.2
JJTapia19
Full Member
KnightRiderX420
Full Member
I have a valid license file, found out about the update, downloaded 2.6 beta formatted sd card put sx os and kosmos on it tried to load it and it just loads the startup sx screen thenm goes black... is it a conflict with kosmos/atlas? if so no problem.... I am going to try to remove the kosmos atlas folders and see if that fixes it.
First timer. Not sure what to do now.
1) Downloaded the sx os 2.6 beta to sd card and placed the sx os licence.dat (activated via website using sx os 2.5.3)
2) Backup NAND on my 7.0.1 OFW.
3) Created emunand on 7.0.1 OFW.
Are these steps correct?
How do I load the emunand that I just created? Should I be using emnuand starting now?
1) Downloaded the sx os 2.6 beta to sd card and placed the sx os licence.dat (activated via website using sx os 2.5.3)
2) Backup NAND on my 7.0.1 OFW.
3) Created emunand on 7.0.1 OFW.
Are these steps correct?
How do I load the emunand that I just created? Should I be using emnuand starting now?
The steps sounds correct
On my switch i have an orange button on the meny screen where i can chose emunand enable or disable, set it to enable and then boot cfw (sxos)
KnightRiderX420
Full Member
it booted but for some reason i am getting invalid license.... I am going to try to put my nand backup of 6.2 back on and see if it still happens if not i want to know how i can fix it. i already tried resubmitting my license.dat and crewating a new one but that failed to....... i'll be back with my results once its finished
i think i figured out my problem emunand was enabled but i didnt make 1 will be back. one more thing now that on 7.01 firmware does swx payload need to be sent threw using hekate? and if my license still says invalid how can i proove its legit. as i can assure you it is... and its never been shared
i think i figured out my problem emunand was enabled but i didnt make 1 will be back. one more thing now that on 7.01 firmware does swx payload need to be sent threw using hekate? and if my license still says invalid how can i proove its legit. as i can assure you it is... and its never been shared
Last edited:
NeoXtremeGamer
Noob Account
Any ETA on a patch to fix USB External HDD Loading? BTW: Thanx for your hard work Guys! Been waiting patiently for this update.
As mentioned so many times before, TX does not give any ETAAny ETA on a patch to fix USB External HDD Loading? BTW: Thanx for your hard work Guys! Been waiting patiently for this update.
Let the DEV team have a little rest
NeoXtremeGamer
Noob Account
Sitting on the side lines looking at it from another point of view I can see where you are coming from.As mentioned so many times before, TX does not give any ETA
Let the DEV team have a little rest
i'm sure they've been dealing with alot of pressure from the people who support this product and have been under fire for a while by the nay sayers and people who are or were pretty impatient. Again TX thanx for all your hard work and keep at it. I will continue to wait patiently until this gets resolved. Easy work around is to simply install what you are going to play on NAND or SD card with updates. End result is still the same we finally have support on 7.0.1 now I can update Smash to latest version and play
Last edited:
I have the NAND back up on 6.2 before, but I accidentally updated to 7.0.1. Do I still need to do another NAND backup on 7.0.1?
- Status