Hello everybody, i recently tried to update my flash on my modded xbox [Phat Liteon- DG-16d2s fw: 7480C] after some time of paying someone to do it. The flashing portion was relatively simple, at one point in jungleflasher there was a period where it would no longer read my drive but I was able to find a guide to get through that. To my disappointment and frustration when I tried to test out if the flash had worked I was getting the dreaded open tray error. So I opened the xbox back up made sure everything was plugged in and reflashed back to stock. After multiple tries I figured that my laser had busted as I had left it plugged in during the flashing processes. My brother has an older xbox that he lost the power cord to but was still a lite-on drive so I switched out the laser with his. I believe it is working because when i plug in the drive with out the casing I can see the laser fire up in preparation for to read the disk. The open tray problem persisted, so I made a post on here and they suggested putting the rubberband in boiling water, which unfortunately didn't work, so I dug around my tools and found a multimeter and tried a pot tweak. I brought it from ~6 OHMS to 3.06 OHMS, trying every .25 in between those two numbers. Right now in its current state It reads disks for ~30-45 seconds before giving the open tray error. I'm afraid to lower it anymore because I don't want the laser to pop. Right no I am at a loss for what to do as I'm not sure if the problem is I've flashing wrong the whole time or both lasers just happened to go out at the same time. The reason I did not post this on my old post was because a few weeks have passed and I realized i left out some potentially important info.
attached below is on of my jf logs
attached below is on of my jf logs
Code:
~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~
JungleFlasher 0.1.94 Beta (320)
Session Started Wed Jul 24 22:40:09 2013
This is a 32 bit process running on a 32 bit CPU
portio32.sys Driver Installed
portio32.sys Driver Started, thanks Schtrom !
Found 4 I/O Ports.
Found 0 Com Ports.
Found 4 windows drives C: D: E: Z:
Found 1 CD/DVD drives Z:
Loading firmware file C:\Documents and Settings\Victor Lua\My Documents\Dummy.bin
MD5 hash: 30c582dba58a64a409ca4bff1238024d
Inquiry string found
Identify string found
Drive key @ 0xA030 7ED75C3D462316264D99848F3E4FAF93
Firmware Osig: [PLDS DG-16D2S 7485]
Firmware is: PhatKey Extract
Loading firmware file C:\Documents and Settings\Victor Lua\Desktop\JungleFlasher v0.1.94 Beta (320)\firmware\Ixtreme\Stock firmware\LiteOn (Phat)\LiteOn_Post_13141\orig-02510C-1c000.bin
MD5 hash: e7e0f802769fd80329784ca4b512f1a9
Drive key @ n/a FFFFFFFFFFFFFFFFFFFFFFFFFFFFFFFF
Firmware Osig: [PLDS DG-16D2S 0251]
Firmware is: Stock
Spoofing Target
DVD Key copied to target
Target is LT - ID strings not copied to Target
Target rev is LT 02510C, serial info not copied
Attempting to verify Source Key to drive on port 0x0970
Key found in KeyDB at record (1 - My Documents)
Key is: 7ED75C3D462316264D99848F3E4FAF93
Key has been tested and verified, thanks C4eva !
Sending Lite-On-Erase request to port 0x0970
..............
Drive returned Status 0xD0
................
Serial flash found with Status 0x72
Manufacturer ID: 0xEF
Device ID: 0x11
Flash Name: Winbond/NEX(W25P20/NX25P20)
Flash Size: 262144 bytes
Getting Status from port 0x0970
SPi flash found with Status 0x72
Sending Chip Erase to Port 0x0970
Erasing:
Writing target buffer to flash
Writing Bank 0: ................
Writing Bank 1: ................
Writing Bank 2: ................
Writing Bank 3: ................
Flash Verification Test !
Reading Bank 0: ................
Reading Bank 1: ................
Reading Bank 2: ................
Reading Bank 3: ................
Write verified OK !
Sending Vendor Outro to port 0x0970
Drive is Lite-On..
