LITEON 74850 open tray with backup but plays my original fine

[pilldoc]

I have a liteon 74850 drive that I reverted to stock, then updated dash to 13599 then flashed to 2.0 and I get open tray on backups but plays my original just fine. I have the latest jungleflasher and current drivers using the ck3i and probe 3. Any suggestions would be great. I even replaced the laser to see if that was the problem but it does the same. Thanks

 

[BL4K3Y]

Post your JungleFlasher log here, or better still... Pastebin it.

 

[DrunkenNinja]

Sounds like it didn't flash correctly if it still plays originals, or for some reason it is flashing from stock to stock.

There could be a whole host or reasons for this, from bad media to bad flash properties, Jungle flasher log would clear some of this up.

 

[pilldoc]

Thanks for you guys's help and here is my JF log




~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~
JungleFlasher 0.1.89 Beta (284)
Session Started Sun Oct 16 06:53:30 2011

This is a 32 bit process running on 8 x 32 bit CPUs
X360USB PRO detected, Version 0.18

portio32.sys Driver Installed
portio32.sys Driver Started, thanks Schtrom !
Found 5 I/O Ports.
Found 1 Com Ports.
Found 10 windows drives C: D: E: F: G: H: I: J: K: L:
Found 1 CD/DVD drives D:

Drive is Lite-On..

Key found in KeyDB at record (22 - Lite on replacement)
Key is: 948EFAD0FC8C8D387B035D12E4B70108
Key has been tested and verified, thanks C4eva !
Drive is Lite-On..

Key found in KeyDB at record (22 - Lite on replacement)
Key is: 948EFAD0FC8C8D387B035D12E4B70108
Key has been tested and verified, thanks C4eva !
Sending Vendor Intro to port 0x0000
Status 0x51
Re-sending Vendor Intro:
.
Serial flash found with Status 0x52

Extracted drive key passed Verification !

key returned: 948EFAD0FC8C8D387B035D12E4B70108
0000: 05 80 00 32 5B 00 00 00 - 50 4C 44 53 20 20 20 20 ...2[...PLDS
0010: 44 47 2D 31 36 44 32 53 - 20 20 20 20 20 20 20 20 DG-16D2S
0020: 30 32 35 31 30 43 41 30 - 41 30 44 36 30 38 43 47 02510CA0A0D608CG
0030: 37 33 38 38 30 38 30 30 - 33 34 38 20 20 20 00 00 73880800348 ..
0040: 00 00 00 00 00 00 00 00 - 00 00 00 00 00 00 00 00 ................
0050: 00 00 00 00 00 00 00 00 - 00 00 00 00 00 00 00 00 ................

0000: 05 80 00 32 5B 00 00 00 - 50 4C 44 53 20 20 20 20 ...2[...PLDS
0010: 44 47 2D 31 36 44 32 53 - 20 20 20 20 20 20 20 20 DG-16D2S
0020: 30 32 35 31 30 43 20 20 - 00 00 00 00 00 00 00 00 02510C ........
0030: 00 00 00 00 00 00 00 00 - 00 00 00 00 00 00 00 00 ................
0040: 00 00 00 00 00 00 00 00 - 00 00 00 00 00 00 00 00 ................
0050: 00 00 00 00 00 00 00 00 - 00 00 00 00 00 00 00 00 ................

0000: C0 85 00 00 00 00 00 00 - 00 00 00 00 00 00 00 00 ................
0010: 00 00 00 00 44 36 30 38 - 43 47 37 33 38 38 30 38 ....D608CG738808
0020: 30 30 33 34 38 20 20 20 - 00 00 00 00 00 00 32 30 00348 ......20
0030: 31 35 43 30 20 20 4C 50 - 53 44 20 20 20 20 47 44 15C0 LPSD GD
0040: 31 2D 44 36 53 32 20 20 - 20 20 20 20 20 20 20 20 1-D6S2
0050: 20 20 20 20 20 20 20 20 - 20 20 20 20 20 20 00 00 ..
0060: 00 00 00 0B 00 00 00 04 - 00 02 06 00 00 00 00 00 ................
0070: 00 00 00 00 00 00 00 00 - 00 00 00 00 00 00 00 00 ................
0080: 03 00 78 00 78 00 E3 00 - 78 00 00 00 00 00 00 00 ..x.x...x.......
0090: 00 00 00 00 00 00 00 00 - 02 02 00 00 68 00 00 00 ............h...
00A0: 00 00 00 00 00 00 00 00 - 00 00 00 00 00 00 00 00 ................
00B0: 20 20 00 00 ..

0000: 44 36 30 38 43 47 37 33 - 38 38 30 38 30 30 33 34 D608CG7388080034
0010: 38 20 20 20 FF FF FF FF - FF FF FF FF FF FF FF FF 8 ............
0020: FF FF FF FF FF FF FF FF - 41 30 FF FF FF FF FF FF ........A0......
0030: FF FF FF FF FF FF FF FF - FF FF FF FF FF FF FF FF ................
0040: FF FF FF FF FF FF FF FF - FF FF FF FF 41 30 FF FF ............A0..


Dummy.bin file saved to Dummy.bin
Loading firmware from buffer
Inquiry string found
Identify string found
Drive key @ 0xA030
Firmware Osig: [PLDS DG-16D2S 0251]
Firmware is: PhatKey Extract
Key database updated

Auto-Loading firmware file E:\JungleFlasher.0.1.89.Beta(284)\JungleFlasher v0.1.89 Beta (284)\firmware\LTPlus-025-v2.0.bin
MD5 hash: 0264149996f783b54629c1598072e50e
Genuine LT plus v2.0
Drive key @ n/a FFFFFFFFFFFFFFFFFFFFFFFFFFFFFFFF
Firmware Osig: [PLDS DG-16D2S 0251]
Firmware is: LT-Plus 2.0
Spoofing Target
DVD Key copied to target
Target is LT - ID strings not copied to Target
Serial data already matches

Target rev is LT 02510C, serial info not copied
Spoofing Target
DVD Key already matches
Target is LT - ID strings not copied to Target
Serial data already matches

Target rev is LT 02510C, serial info not copied

Target f/w saved as: Lite_CFW.bin
Spoofing Target
DVD Key already matches
Target is LT - ID strings not copied to Target
Serial data already matches

Target rev is LT 02510C, serial info not copied

Sending Lite-On-Erase request to port 0x0000
..............
Drive returned Status 0x0
.....
Serial flash found with Status 0x72
Manufacturer ID: 0xC2
Device ID: 0x11
Flash Name: MXIC(MX25L2005)
Flash Size: 262144 bytes

Getting Status from port 0x0000
SPi flash found with Status 0x72

Sending Chip Erase to Port 0x0000
Erasing:
Writing target buffer to flash
Writing Bank 0: ................
Writing Bank 1: ................
Writing Bank 2: ................
Writing Bank 3: ................

Flash Verification Test !
Reading Bank 0: ................
Reading Bank 1: ................
Reading Bank 2: ................
Reading Bank 3: ................
Write verified OK !

Sending Vendor Outro to port 0x0000
Drive is Lite-On..

Key found in KeyDB at record (22 - Lite on replacement)
Key is:
Key has been tested and verified, thanks C4eva !

 

[alyshehata]

ur log looks fine. probably a problem burning games. did u set the correct layerbreak ?


Edit: btw, last few lines have "Key is: " did u delete the key urself or is it like that ? coz i can see the key at the beginning

 

[frazzeld]

The question that needs to be answered is....did the backup you are attempting to play work previously before you updated?

 

[pilldoc]

Layer break - Yes, Did they work fine before - Yes and Did I delete the last few line of key - Yes..... Its the wierdest thing. I have never experienced this before. At least it gives me something to work on and figure out. You think a POT TWEAK is worth trying?

 

[frazzeld]

Never had to do a Pot Tweak....Have you got a multi meter? you'll need one to do it correctly

"It does sound like a weak laser"

 

[pilldoc]

Im thinking a weak laser also because it reads for a good minute and you can hear the laser trying its best to do something but just falls short and says open tray.... The laser i replaced it with came from a liteon replacement i recieved as payment for another xbox fix so it may be coincidental they are both weak lasers. Thanks again for all you guy's help.

 

[knowlzy10]

have a read through this guide here http://team-xecuter.com/forums/showthread.php?t=61768

i no this topic is open for debate but i personally always remove laser ribbon, did you remove it for the flash, also did you replace laser with a new one? if so have you double checked anti solder blob been removed corectly, very rare needing to pot tweak a new laser m8:biggrin:

 

[pilldoc]

Oh yea I learned the hard way a long time ago on removing the cable ribbon..... The laser came out of a refurbed replacement.

 

[knowlzy10]

Oh yea I learned the hard way a long time ago on removing the cable ribbon..... The laser came out of a refurbed replacement.

i would try and steer clear of refurb ones if i was you,

try the pot tweak its easy to do with right equiptment see if that works,

what colour is your laser to look at not the actual laser the lens mate?

 

[pilldoc]

Just tested with multi-meter and its reading 2.74 and i'm reading that unless its factory set below 3 then dont go lower.... I'm leaving it alone and I will be getting a new drive to see if that fixes the problem.... Thanks for all your help

 

[knowlzy10]

Just tested with multi-meter and its reading 2.74 and i'm reading that unless its factory set below 3 then dont go lower.... I'm leaving it alone and I will be getting a new drive to see if that fixes the problem.... Thanks for all your help

dont need a new drive m8 just a new laser not a refurbed one, looking at that reading its fairly low hence why the diode is not reading backups, a new laser a lot cheaper than a drive

if the lens is blue in colour to look at no doubt its dodgy, should be clear to look at

 

[pilldoc]

I see what your saying now.... And yes it has a color to it, certainly not clear.... Thanks for the advice. I will shop for a laser instead.