voltage help !!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!
Hey quick question, what should LPC pin 1s voltage be, I read on a sight it is 0.02, But this is y i ask, I had a major ,major,major,major ... Trace break, it the lead from PIN 1, Tryed to repair, wouldent happen, so i looked on like where to bridge it, so i tryed that and it totaly F***ed up the Rivet
so my box was fragging hardcore, and i decided since its broke it cant hurt to break it more anyway i traced the lead to the other side of the board and to under the Grafix Prosessor, i couldent trace the lead to the main point under the processor so i used a small piece of the trace about half an inch from the chip and soldered a trace bridge from there to the LCP pin, and BAMMOWAMMOWAMMY WAMS ! it booted fine and runs fine, ok not that i used a multi - meater on my pin header it find the grounds are 0.0 , most are 3.3, the ones 5.5 and my Pin one ( read its 0.02Volts) goes from 1.68Volts to 0.02 Volts and jumps around, the mod chip boots to the flashbios screen and i cant continue from there after flashing n all that. All so, I was reading about mod chips and one said it used a 5.5 Volt , and 1.6 Volt connection, witch my power output is in that range so ....i dont understand .....When will it all modd ....when will the pain end, and the tears stop .... Sniffle..sniffle .. O O sorry sorry thinking of the last 3 months of this modding thing .. If anyone at all can help please do thanks
PS I DO NOT HAVE THE RESET SWITCH ADAPTER INSTALLED, IF THIS IS THE PROBLEM LET ME KNOW
iF ANYONE CAN SHOW ME A BETTER PLACE FOR THE JUMP BRIDGE (TO LPC PIN 1 ) LET ME KNOW PLEASE =)
Its very very sad when your life becomes sleep work TRY TO MODD =(
Hey quick question, what should LPC pin 1s voltage be, I read on a sight it is 0.02, But this is y i ask, I had a major ,major,major,major ... Trace break, it the lead from PIN 1, Tryed to repair, wouldent happen, so i looked on like where to bridge it, so i tryed that and it totaly F***ed up the Rivet
so my box was fragging hardcore, and i decided since its broke it cant hurt to break it more anyway i traced the lead to the other side of the board and to under the Grafix Prosessor, i couldent trace the lead to the main point under the processor so i used a small piece of the trace about half an inch from the chip and soldered a trace bridge from there to the LCP pin, and BAMMOWAMMOWAMMY WAMS ! it booted fine and runs fine, ok not that i used a multi - meater on my pin header it find the grounds are 0.0 , most are 3.3, the ones 5.5 and my Pin one ( read its 0.02Volts) goes from 1.68Volts to 0.02 Volts and jumps around, the mod chip boots to the flashbios screen and i cant continue from there after flashing n all that. All so, I was reading about mod chips and one said it used a 5.5 Volt , and 1.6 Volt connection, witch my power output is in that range so ....i dont understand .....When will it all modd ....when will the pain end, and the tears stop .... Sniffle..sniffle .. O O sorry sorry thinking of the last 3 months of this modding thing .. If anyone at all can help please do thanks PS I DO NOT HAVE THE RESET SWITCH ADAPTER INSTALLED, IF THIS IS THE PROBLEM LET ME KNOW
iF ANYONE CAN SHOW ME A BETTER PLACE FOR THE JUMP BRIDGE (TO LPC PIN 1 ) LET ME KNOW PLEASE =)
Its very very sad when your life becomes sleep work TRY TO MODD =(
Last edited: