In my defence when i am installing RGH/R-JTAG, I leave the Nand-X wires installed until I flash the final image. Then I unsolder them. This way I know if I can read/write the stock nand/ECC, that it isnt a problem with my wiring if i end up with an issue like this. As for the advice I gave, it was an educated guess based upon my experience, and what the op said.
JUNGLE FLASHER Please help this new guy with an R-JTAG / Jungleflasher issue
- Thread starter JamesFrazled
- Start date
WARNING! - Your selected working directory already contains files!
You can view these files by using 'Show Working Folder' Button
Checking Files
Finished Checking Files
Initializing nanddump1.bin..
Jasper 16MB
Jtag Selected
Nand Initialization Finished
Retail Selected
Version: 10
Flash Config: 0x00023030
Writing Nand
nanddump1.bin
Done!
in 3:29 min:sec
Well gents....I by gents I mean the ones that are being helpful and not cynical, I redid my solder...twice matter factly, managed to right my retail nand.bin to the NAND (hurray!)......but now...sadly....I HAVE NO POWER to my console? Nothing.....dead stone. I will post pictures shortly of the soldering of the nandx. You will notice that the RJtag is (5V) is deliberately disconnected from the board as I wanted nothing to affect the write to the nand. Gents....PLEASE help me with easy lingo on where I need to test for reason(s) I now have no juice running through my Xbox 360? Pics coming up!
You can view these files by using 'Show Working Folder' Button
Checking Files
Finished Checking Files
Initializing nanddump1.bin..
Jasper 16MB
Jtag Selected
Nand Initialization Finished
Retail Selected
Version: 10
Flash Config: 0x00023030
Writing Nand
nanddump1.bin
Done!
in 3:29 min:sec
Well gents....I by gents I mean the ones that are being helpful and not cynical, I redid my solder...twice matter factly, managed to right my retail nand.bin to the NAND (hurray!)......but now...sadly....I HAVE NO POWER to my console? Nothing.....dead stone. I will post pictures shortly of the soldering of the nandx. You will notice that the RJtag is (5V) is deliberately disconnected from the board as I wanted nothing to affect the write to the nand. Gents....PLEASE help me with easy lingo on where I need to test for reason(s) I now have no juice running through my Xbox 360? Pics coming up!
jsinger47
Troll Eating Dogs
Well, your flash config is wrong. Notice how it says 23030? A 16MB console would have a 23010 flash config.
Even stranger, you claim this is a big block console?
Something is really wrong here.
Even stranger, you claim this is a big block console?
Something is really wrong here.
....now I can't seem to upload pics? There are .jpg
I was able to before (above). What is the max pixel size allowable?
I was able to before (above). What is the max pixel size allowable?
jsinger47
Troll Eating Dogs
NO POWER TO CONSOLE.
I have a dead stick now. :facepalm:
I can now write to the NAND, but with the same repeated error over and over again....block 0.
Can you guys help with finding the most likely place to look for a short on my board? I'm suspecting a small solder ball or tiny pc. of wire may have been on the board when I fired it up after re-soldering my nandx wires again (for the 5th time).....and yes...it was the soldering connection the whole time fellas! Thanks for the worldly advice.....but now....I have no juice to the board and that really sucks!
August-28-14 10:35:12 PM
J-Runner v0.3 Beta (4) Started
WARNING! - Your selected working directory already contains files!
You can view these files by using 'Show Working Folder' Button
Checking Files
Finished Checking Files
Initializing nanddump2.bin..
Jasper 16MB
Jtag Selected
Nand Initialization Finished
Retail Selected
Version: 00
Wrong Version.
Version: 10
Flash Config: 0x00000010
Writing Nand
nanddump2.bin
IoTimedOut
Error: 010 writing block 0
Done!
in 3:31 min:sec
Version: 00
Wrong Version.
Version: 10
Flash Config: 0x00000010
Writing Nand
nanddump2.bin
IoTimedOut
Error: 010 writing block 0
Done!
in 3:31 min:sec
I have a dead stick now. :facepalm:
I can now write to the NAND, but with the same repeated error over and over again....block 0.
Can you guys help with finding the most likely place to look for a short on my board? I'm suspecting a small solder ball or tiny pc. of wire may have been on the board when I fired it up after re-soldering my nandx wires again (for the 5th time).....and yes...it was the soldering connection the whole time fellas! Thanks for the worldly advice.....but now....I have no juice to the board and that really sucks!
August-28-14 10:35:12 PM
J-Runner v0.3 Beta (4) Started
WARNING! - Your selected working directory already contains files!
You can view these files by using 'Show Working Folder' Button
Checking Files
Finished Checking Files
Initializing nanddump2.bin..
Jasper 16MB
Jtag Selected
Nand Initialization Finished
Retail Selected
Version: 00
Wrong Version.
Version: 10
Flash Config: 0x00000010
Writing Nand
nanddump2.bin
IoTimedOut
Error: 010 writing block 0
Done!
in 3:31 min:sec
Version: 00
Wrong Version.
Version: 10
Flash Config: 0x00000010
Writing Nand
nanddump2.bin
IoTimedOut
Error: 010 writing block 0
Done!
in 3:31 min:sec
Last edited:
NOTE
NOTE
Managed to shrink pics to fit to size! Still can't figure out the insert URL thing!
Attachments
Last edited:
Ok. Uploaded pic to imgur.com but I'm having difficulty loading it to the page. Get an error that says "error: invalid file"? I've tried uploading every link listed on the right side....no dice!?
Last edited:
I've got some life back in the Jasper! Shorted pins 44-47 (across the nand's resistors) just a couple of times, flashed retail nand back to Jasper, disconnected power, waiting 30 seconds....now it powers up at least!
New problem though...won't load original dash after retail flash? Middle green light on console just flashes...that's it!? Suggestions....please?
New problem though...won't load original dash after retail flash? Middle green light on console just flashes...that's it!? Suggestions....please?
Last edited: