RGH Post QSb Slim Lifted Severe Help Needed

[thebomber]

hey guys just now, i had this glitched slim, which wasnt glitching well, i was insulating the cables, and dont knw what happened the qsb was ripped of the mobo
i guess 8 points were torn

i will try to attach a picture in a few min

this is so bad, i returned the stock nand, and i get 3 green lights, and fan starts for 1 sec, then switches off

any help

 

[Hackerjac]

damn that sounds really bad

 

[thebomber]

here are the pics

 

[vrtclhykr]

You must have caught an edge whilst flipping over mainboard.

Question though...... Why did you solder all those points?

That QSB only needs 2 for Coolrunner

 

[trippy86]

You must have caught an edge whilst flipping over mainboard.

Question though...... Why did you solder all those points?

That QSB only needs 2 for Coolrunner

true it does only need two, but i found it to be more secure and sturdy installation with these point soldered. i just cant understand how you managed this.

can you post some more clear close up, need to see the points more clearly

make sure none of these points are bridged in anyway (unlikely but i would double check). Also have a very close look in the general area and make sure all resistors are in place, they can be very easy to tear off the board

 

[thebomber]

dont know actually guess cause the qsb had the points there i soldered and didnt know if it was needed or not, as well as to hold the qsb firm and not wobble,

so the 3 green rings, is due to the post out being messed up, i can manage the alternative for that, i mean the others got to be doing something, right

 

[thebomber]

and now the nand x is giving me no device detected as if my soldering is sh*t, i wrote back the original nand like 2 hours ago, now its not detected, tried on several consoles, looks like something is wrong with the nandx , i flashed v3 and pressed the reset button still the same

any clue

 

[trippy86]

silly questions but did you make sure the 360 power cord is plugged in? also if you have another console try checking if the nand-x still works with it to rule that out.

 

[thebomber]

Yes im sure the power cable is plugged the weird thing is its recognized at device manager tried using the wire install nothing there had a slim i did yesterday plugged the cables to the qsb nothing there anyway when i wake up i will reinstall windows and try. this is a mess nand x busted and points out.

Anyway only those 8 points are out i just want to know if the other points do something or alt points i want to try the post out alt but im totally not in the mood to crank this box now im totally frustrated. Anyway thx for the help and i guess im the first to actually manage to take the qsb off. just saying

---------- Post added at 21:31 ---------- Previous post was at 21:28 ----------

And for the picture will try again in the moring after i look for the magnifying glass and take a clear shot

 

[thebomber]

so i took the alt of the yellow wire and installed to the coolrunner, still 3 green lights and fans turn off after 1 second


any clue guys on the other points where i should connect them to get the console booting again

 

[DreamZ]

so i took the alt of the yellow wire and installed to the coolrunner, still 3 green lights and fans turn off after 1 second


any clue guys on the other points where i should connect them to get the console booting again

you need to repair the damaged caused by the lifted qsb. 3 flashing green lights, ive never seen that. need to fix that first before thinking about alt cr points

 

[thebomber]

Ok any help where they are and to where i can solder them its a shame it was ripped off i guess its stupid and weird that the cable ripped the board off maybey it wasnt soldered that great dont know actually so any one with a clue of what i should do next

 

[trippy86]

as stated earlier in the thread you need to post some more detailed, close up photos. without these your not going to get much help. get the photos and post back

 

[thebomber]

i cant manage to find a decent camera or anything with zoom to take a decent photo

if anyone attached the pst qsb , there are 8 points to be soldered, all i need are the alternatives for them, they are all wasted, nothing else is ruined, i measured the alternative is on the other side of the board exactly but to where should i solder them for the console to work

 

[esbmaepo]

so i took the alt of the yellow wire and installed to the coolrunner, still 3 green lights and fans turn off after 1 second


any clue guys on the other points where i should connect them to get the console booting again

Does STBY_CLK look allright?

 

[thebomber]

swapped the board with a dude and paid him difference lol

check my other topic with the messed up trinity board