LITEON DG-16D2S POWER OFF WHILE WRITING

[snowboard_extr3me]

Unfortunately power of my xbox went off while writing the new lt 2.0 plus.
Now the drive won't eject and it can't get recognized under jf by any means.
In dosflash it gets recognized as unknown chip with status 0x52, i tried erasing writing etc. but it doesn't work since it says "unknown chip".
Am I f**ked up? I have the key obviously....
Do I need to buy a whole new drive or can I buy only the logic board, to save a bit?
Can I recover it?

Thanks mates!!!

 

[banjaxt]

we need more info i.e. drive model, power source etc. and please, no swearing

 

[rdubbs007]

Badflash recovery should get it working fine. Erase the port. Intro the port and power cycle the drive and your flash props should 'splay.

---------- Post added at 13:58 ---------- Previous post was at 13:57 ----------

we need more info i.e. drive model, power source etc. and please, no swearing

model is jasper liteon, it is in his xbox setup in his sig.

 

[snowboard_extr3me]

the model is 16d2s phat a0a1, the power source was the xbox 360 itself, the xbox is falcon i think, it has a bigger power source than mine which is jasper of october 09
the xbox powered off while it was writing bank 1.....

 

[Martin C]

Yep it should be fine. Connect it up and select lite-on erase.

You should be able to put it into Vendor mode after this and re-write the firmware.

It probably powered off as you didn't have an AV cable connected. We DO NOT recommend using the 360 as a power source for this very reason.

 

[sp4rkst4rt3r]

Unfortunately power of my xbox went off while writing the new lt 2.0 plus.
Now the drive won't eject and it can't get recognized under jf by any means.
In dosflash it gets recognized as unknown chip with status 0x52, i tried erasing writing etc. but it doesn't work since it says "unknown chip".
Am I f**ked up? I have the key obviously....
Do I need to buy a whole new drive or can I buy only the logic board, to save a bit?
Can I recover it?

Thanks mates!!!

This is the PRIME reason why we advise peeps not to use console for power whilst flashing....

I'm not having a dig at the OP (he may not have known and been advised wrongly) :eek2:

This thread http://team-xecuter.com/forums/showthread.php?t=71924 is an example of the good advice most of us give relating to this very issue :wink:

Don't worry OP these guys will get you fixed up in no time :tongue:

 

[manwithoutname]

I have given up long time ago. You can bring water to the horse but you can't force the horse to drink .

 

[Goldensavage]

As Martin says, hook it up with an av cable connected

And lite-on erase it to get it back to vendor mode.... (I know it doesn't show) Just select the correct port and pretend it is there. it will show after erase.

And get yourself a ck3 before you do even more damage

 

[snowboard_extr3me]

UPDATE:
after liteon erase in jf I get status 0x80, but still no drive detected..After this I do intro device id, when I power off and on the status switches from 0x80 to 0x52 but then goes back to 0x80 while under that the "..."dots keep going....

 

[Martin C]

Can you post your JF logs?

 

[snowboard_extr3me]

~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~
JungleFlasher 0.1.88 Beta (280)
Session Started Tue Jan 01 15:21:09 2002
This is a 32 bit process running on a 32 bit CPU
portio32.sys Driver Installed
portio32.sys Driver Started, thanks Schtrom !
Found 2 I/O Ports.
Found 2 Com Ports.
Found 2 windows drives A: C:
Found 0 CD/DVD drives

Sending Lite-On-Erase request to port 0xD000
..............
Drive returned Status 0x80
....................
Device Intro failed!
Sending Vendor Intro to port 0xD000
Status 0x80
Re-sending Vendor Intro:
........................................................................................................................................................................................................................................
Device Intro failed!

---------- Post added at 13:46 ---------- Previous post was at 13:42 ----------

I made it 0x72 thank you soo much!!!

 

[frayed]

you do realize this is a TX product support forum?

are you even using any team xecuter products?

edit: i was writing before you got your 0x72

guess the lesson you should learn from this experience would be to buy a ck3