hello i have conect my sd card reader in the console i have use this sd card in alot console before but first time in corona v4 with BGA nand and i am taking this error from j runner
but only when i am try to make a full backup . in the backup that is 49 mb it take it like normal . anyway i deside to write the DGX ecc and to procced . i do not have yet a post fix adapter so i made the fix with the dremel and i have conect the solder ball under the cpu ... everything go fine end in 20 sec i have the cpu key in my pc ... i have fix the image updflash .bin and when i am trying to write the image the gives me a message that it is not the correct size image . i am write anyway the nand and i use a cr3 but it glitch for ever .. any ideas ... ?
i have bridge the pads on the resistor for E and F point ..
in this photo
you have write that must be bridged the point R2C10 , it is already bridget like the photo . or must be bridget to make it 0 ohm .
when i write the stock i have again the same error that is wronk size image but console works fine in stock ...
here is the log from the jrunner
Πέμπτη, 17 Ιανουαρίου 2013 3:39:51 μμ
J-Runner v0.2 Beta (284) Started
Consider fellow users, Save bandwidth, please have only minimum number of dashes selected.
Checking Files
Finished Checking Files
F:\
Reading from F:\ to corona4a.bin
Done!
in 0:03 min:sec
F:\
Reading from F:\ to corona4b.bin
Done!
in 0:03 min:sec
F:\
Reading from F:\ to corona4c.bin
Done!
in 0:03 min:sec
F:\
Reading from F:\ to corona4full.bin
System.IO.IOException: Data error (cyclic redundancy check).
at System.IO.__Error.WinIOError(Int32 errorCode, String maybeFullPath)
at System.IO.FileStream.ReadCore(Byte[] buffer, Int32 offset, Int32 count)
at System.IO.FileStream.Read(Byte[] array, Int32 offset, Int32 count)
at JRunner.Forms.LDrives.read()15257
Could not find a part of the path.
and here is when i am trying to write the updflash.bin ( freeboot image )
but only when i am try to make a full backup . in the backup that is 49 mb it take it like normal . anyway i deside to write the DGX ecc and to procced . i do not have yet a post fix adapter so i made the fix with the dremel and i have conect the solder ball under the cpu ... everything go fine end in 20 sec i have the cpu key in my pc ... i have fix the image updflash .bin and when i am trying to write the image the gives me a message that it is not the correct size image . i am write anyway the nand and i use a cr3 but it glitch for ever .. any ideas ... ?
i have bridge the pads on the resistor for E and F point ..
in this photo
you have write that must be bridged the point R2C10 , it is already bridget like the photo . or must be bridget to make it 0 ohm .
when i write the stock i have again the same error that is wronk size image but console works fine in stock ...
here is the log from the jrunner
Πέμπτη, 17 Ιανουαρίου 2013 3:39:51 μμ
J-Runner v0.2 Beta (284) Started
Consider fellow users, Save bandwidth, please have only minimum number of dashes selected.
Checking Files
Finished Checking Files
F:\
Reading from F:\ to corona4a.bin
Done!
in 0:03 min:sec
F:\
Reading from F:\ to corona4b.bin
Done!
in 0:03 min:sec
F:\
Reading from F:\ to corona4c.bin
Done!
in 0:03 min:sec
F:\
Reading from F:\ to corona4full.bin
System.IO.IOException: Data error (cyclic redundancy check).
at System.IO.__Error.WinIOError(Int32 errorCode, String maybeFullPath)
at System.IO.FileStream.ReadCore(Byte[] buffer, Int32 offset, Int32 count)
at System.IO.FileStream.Read(Byte[] array, Int32 offset, Int32 count)
at JRunner.Forms.LDrives.read()15257
Could not find a part of the path.
and here is when i am trying to write the updflash.bin ( freeboot image )
Last edited:
