problem with deamon

[kipisy9]

when read get this

Hardware : Demon Phat
Firmware : 1.0
Flash ID : 0xDCEC Samsung (512MiB - Big block)
Flash Size : 0x1000 blocks of 0x21000 bytes
Invalid Blocks : 0xBA7
Reading Nand
Done!
in 9:37 min:sec

xbox hawe broken south bridge cant read nand with wire
can i continue with Invalid Blocks : 0xBA7 ?

 

[BL4K3Y]

I don't see what the issue is.

That flash ID is correct for a 512MB BB Jasper.

Bad blocks are normal, so don't worry about it (J-Runner has been designed to remap them).

 

[kipisy9]

ok thanks

 

[kipisy9]

now when conect to xbox to pc got

device for code FC not found

 

[BL4K3Y]

now when conect to xbox to pc got

device for code FC not found

We need to see photos of the DemoN install.

 

[kipisy9]

image
http://foto.inbox.lv/kipisy9/demon

 

[BL4K3Y]

Can you confirm that there is continuity between each DemoN test point and the NAND points on top of the board?

Did you get a good NAND read before or after installing the conversion kit?

 

[kipisy9]

yes,i instal all this then got 2 same reads with

Hardware : Demon Phat
Firmware : 1.0
Flash ID : 0xDCEC Samsung (512MiB - Big block)
Flash Size : 0x1000 blocks of 0x21000 bytes
Invalid Blocks : 0xBA7
Reading Nand
Done!
in 9:37 min:sec

bouth same
what conversion kit?

 

[BL4K3Y]

yes,i instal all this then got 2 same reads with

Hardware : Demon Phat
Firmware : 1.0
Flash ID : 0xDCEC Samsung (512MiB - Big block)
Flash Size : 0x1000 blocks of 0x21000 bytes
Invalid Blocks : 0xBA7
Reading Nand
Done!
in 9:37 min:sec

bouth same
what conversion kit?

I'm talking about the BB conversion kit you installed.

Was that installed before you read the NAND?

 

[kipisy9]

no i instal and then read

 

[kipisy9]

i can read xbox nand trouth microusb,if yes xbox need to conected to power and swich to xbox?

 

[kipisy9]

now upgrade demon version 1.04
got this mesage
Manufacturer: Samsung
Device: K9F4G08U0M
Device Id: 0xECDC
Number of Blocks: 4096
Number of Pages per Block: 64
Page Size: 2112 bytes
Number of Invalid Blocks: 1
Addresses of Invalid Blocks: 2983


Full backup selected.
Reading.
ERROR: Block 0, page 0 contains corrupt data.

and in jruner when i start somthing doing show j runer spoed workin and close

 

[kipisy9]

in jruner error got this
System.IndexOutOfRangeException: Index was outside the bounds of the array.
at JRunner.DemoN.getBlockSize()
at JRunner.DemoN.read(String filename, Int32 startblock, Int32 length)
at JRunner.MainForm.readnand(Errors error)
at JRunner.MainForm.<>c__DisplayClass2c.<getconsoletype>b__26()
at System.Threading.ThreadHelper.ThreadStart_Context(Object state)
at System.Threading.ExecutionContext.Run(ExecutionContext executionContext, ContextCallback callback, Object state, Boolean ignoreSyncCtx)
at System.Threading.ExecutionContext.Run(ExecutionContext executionContext, ContextCallback callback, Object state)
at System.Threading.ThreadHelper.ThreadStart()

 

[Martin C]

At this point you may want to consider sending it to a pro.

 

[kipisy9]

first time run xbox with demon soldered got e71,then 3 red light and then no power(can tur on)all desoldered works fine

 

[Martin C]

I have a feeling you're not interested in anyone else's opinion.

Send this to a Pro. You're learning very quickly it's not a noob install.

You should know what causes E71.