problems with nand-x

[mickeyvilla]

the other thing to eliminate here is v3 hex file. If you still have the ability, download nandpro 2.0d and flash the armv2.hex supplied to your NAND-x. See if this changes anything.

I've been thinking about this recently and my LPC-2148 project board was working fine, right up to flashing it with v3 hex and I had intermittent errors after this with certain boards.

no i aint got the ability to do that as the nand-x is the only flasher i've got.

 

[mickeyvilla]

i've desoldered both qsb for nand & inspected board no burnt tracks.
soldered wired straight to board & i'm still having the same trouble(so there was nothing wrong with my soldering).

it has to be either the nand-x flasher or it my comp having compatability issuse with these flashing programes.

i am pissed right off aaarrrrrrggggghhhhhh.

 

[mickeyvilla]

it seems i'm not the only 1 with this problem,


http://team-xecuter.com/forums/showthread.php?t=75099

 

[mickeyvilla]

this has gotto be something to do with programes or 64 bit compatability.
i've set up a slim & still getting same error in cmd "can not find usb interface"

i found that most people who are having same problem as me are running on 64 bit comps aswell.

 

[mickeyvilla]

right now i have my slim done with the rgh,its about time i got this xenon finished or should i say TRY.

after having no luck with qsb or wirers soldered direct to board i decided to try with these little peg boards that came with nand-x.
i've only installed the points i need as u can see,i've checked with mulitimeter there are no shorts & all point run to their alernative soldering points except the red wire i could find an alternative point for that.
i've even checked the points to the back of mobo & all ok.

but i'm still getting error in cmd that it cant find usb interface device.

earlier on in this post i was told i could flash nand through xell.
well i've tried all ways but its not aving it.

i videoed xell bootup hoping some might know where or what i'm doing wrong,heres link to vid.

[ame]http://www.youtube.com/watch?v=xqQsEOn3FNw[/ame]

 

[mickeyvilla]

dont know what happened there with double posting.

i think it was through trying to upload these pics,

 

[mickeyvilla]

part 2

 

[Martin C]

ok

1. you CAN reflash through XeLL. Use Rawflash which comes with multi_builder as your XeLL is looking to boot xenon.elf. So rename the nand file to nandflash.bin and put both files on a USB stick (at the root).

2. Without seeing the board up close, it's hard to tell whether you have any other damage there. pics of the underside would be useful.

 

[mickeyvilla]

ok

1. you CAN reflash through XeLL. Use Rawflash which comes with multi_builder as your XeLL is looking to boot xenon.elf. So rename the nand file to nandflash.bin and put both files on a USB stick (at the root).

2. Without seeing the board up close, it's hard to tell whether you have any other damage there. pics of the underside would be useful.

hi ya martin tried that ^^^^

took pic of result i got but when i boot up after it boots in xell all the time

 

[mickeyvilla]

heres the pics of the under side of mobo.

as i've said i've traced all soldered points to there alterative points execpt red wire but traced it along that circuit i've pointed out in 3rd pic.

 

[Martin C]

For rawflash, try another USB stick. It's having trouble accessing that one.

 

[mickeyvilla]

Tried a few different usb memmory stick & even burn nand & other file to disc but still wont have it.

i totally give up on this 1 yet i know i'm nearly there with it.

 

[Martin C]

What exactly have you copied to the USB stick and where?

File sizes too.

 

[mickeyvilla]

What exactly have you copied to the USB stick and where?

File sizes too.

my freebootnand which i named "nandflash.bin" 16,896kb &
xenon.elf file 272kb.

i just copied & pasted them to (h) drive which is my usb memory stick.

 

[Martin C]

are you sure it's called nandflash.bin and not nandflash.bin.bin?

 

[mickeyvilla]

here took snap shot of it