TX Product(s) used: J-R Programmer
Console Type: Falcon
NAND size: 16
Dashboard version: 16202
CB version: 5774
J-Runner log:
Checking Files
Finished Checking Files
Initializing nanddump1.bin..
Falcon/Opus
Jtag Selected
Nand Initialization Finished
Retail Selected
Version: 10
Flash Config: 0x01198010
Writing Nand
nanddump1.bin
Error: 280 writing block 0
IoTimedOut
Error: 621 writing block 2
IoTimedOut
Error: 001 writing block 3
IoTimedOut
Error: 021 writing block 4
Description of problem:
My Problem is i soldered the Nandx wires to read the Nand from the console with the Jr-Programmer. I dumped the Nand 4 times without errors and they are the same.
I've createt ecc file and treid tto flash it and was getting the Error above.
At this time the console won't boot. I can't read nand or write Nand.
I found the thread for help with bad nand flash. So i bridged the 4 connections and tried to write my orgininal Nand back which worked without Problems.
So i decided to start again from the beginning.
I've dumped the nand again 4 times without erros like before. Createt ecc try to flash and Bam same error again and no Nand readings or writings.
Everytime i get the right Flashconfig.
I treid to update my Jrunner without success.
Can anyone help me with this problem?
I also measuerd the connections of the Nand x Troubleshooting guide. Everything looks goot instead of Pin 1 and 3 they provide only about 0,2-3V
Maybe it's a problem with the Programmer?
Ok i found out that the Problem only occurs if the coolrunner is Solderd into xbox.
I've measuered all wires with multimeter and changed wires and solderd everything new a few times.
If the coolrunner is solderd, the xbox is like dead and wont power up and i'm unable to read or write the Nand.
I'm using a Coolrunner Rev D. with a Falcon. Is this chip not compatible? Before i only used Rev C. with many Falcons without any problems.
The chip is programming fine, and writing back to stock nand if Coolrunner is desolderd works also.
I've removed C8 on Coolruner like i did always on Rev C. before everything else is stock. I Tried al different Timing files, And self createt Ecc and Falccon RGX. ECC
I did not remember but if i put the switch in Prog. mode the red led is lightet just a little bit, like its getting some power from somwewhere it should't get from. Is this normal?
Was the console working before you started: Y
Images:
Console Type: Falcon
NAND size: 16
Dashboard version: 16202
CB version: 5774
J-Runner log:
Checking Files
Finished Checking Files
Initializing nanddump1.bin..
Falcon/Opus
Jtag Selected
Nand Initialization Finished
Retail Selected
Version: 10
Flash Config: 0x01198010
Writing Nand
nanddump1.bin
Error: 280 writing block 0
IoTimedOut
Error: 621 writing block 2
IoTimedOut
Error: 001 writing block 3
IoTimedOut
Error: 021 writing block 4
Description of problem:
My Problem is i soldered the Nandx wires to read the Nand from the console with the Jr-Programmer. I dumped the Nand 4 times without errors and they are the same.
I've createt ecc file and treid tto flash it and was getting the Error above.
At this time the console won't boot. I can't read nand or write Nand.
I found the thread for help with bad nand flash. So i bridged the 4 connections and tried to write my orgininal Nand back which worked without Problems.
So i decided to start again from the beginning.
I've dumped the nand again 4 times without erros like before. Createt ecc try to flash and Bam same error again and no Nand readings or writings.
Everytime i get the right Flashconfig.
I treid to update my Jrunner without success.
Can anyone help me with this problem?
I also measuerd the connections of the Nand x Troubleshooting guide. Everything looks goot instead of Pin 1 and 3 they provide only about 0,2-3V
Maybe it's a problem with the Programmer?
Ok i found out that the Problem only occurs if the coolrunner is Solderd into xbox.
I've measuered all wires with multimeter and changed wires and solderd everything new a few times.
If the coolrunner is solderd, the xbox is like dead and wont power up and i'm unable to read or write the Nand.
I'm using a Coolrunner Rev D. with a Falcon. Is this chip not compatible? Before i only used Rev C. with many Falcons without any problems.
The chip is programming fine, and writing back to stock nand if Coolrunner is desolderd works also.
I've removed C8 on Coolruner like i did always on Rev C. before everything else is stock. I Tried al different Timing files, And self createt Ecc and Falccon RGX. ECC
I did not remember but if i put the switch in Prog. mode the red led is lightet just a little bit, like its getting some power from somwewhere it should't get from. Is this normal?
Was the console working before you started: Y
Images:
Last edited:
