Process For Reflashing Possible Corrupt RGH NAND??

L

lettucekl

Full Member
Feb 5, 2014
27
0
I have been having issues with the RGH nand on my 360 (retail nand works fine), basically its been a while since i have used the 360 in RGH mode and think there has been a dash update in between the last time i used the RGH mode and did a dash update (i never updated the RGH nand). I booted up the 360 in RGH mode after a few seconds i got a grey screen with white writing and i think an error code of E71, and then the green power light turned red i turned the 360 off and back on again at which point the internal fan was really loud and nothing happen on the 360 so i turned it off again, left it for about a minute and now when i try and turn the 360 on i get the power on audio sound (ding) but no light comes on on the 360. I appear to be able to get the 360 to power on now and again but have noticed that the 360 boots in 480p display and goes to a screen showing the 360 pad and an arrow point to the home button and then the 'A' button, its as if the 360 has been reset back to factory setup mode!

It has been suggested that the RGH nand might have become corrupt, i tried updated the RGH nand via j-runner but now just get the red power light button on the 360 when i turn it on in rgh mode, its over a year since i updated the RGH nand via j-runner and just want to clarify the method i used in updating my RGH nand was correct....

I have a folder from the last time i update my nand with the following files, which i guess the modder supplied to me as well:

checksum.md5
cpukey.txt
C-R.bin
fcrt_dec.bin
fcrt_en.bin
key.bin
KV_dec.bin
KV_en.bin
KV_info.txt
nanddump1.bin
nanddump2.bin
smc_config.bin
SMC_dec.bin
SMC_en.bin
upflash(120320131741).bin
upflash.bin

In j-runner i....

clicked on 'Load Source' and browsed to nanddump1.bin (from the above list)
clicked on 'Load Extra' and browsed to nanddump2.bin
CPU key was showing in the relevant window
clicked 'Nand Compare' all came back fine
selected dash version 16547 from the dash version drop downlist
selected 'RGH2'
and then clicked on 'Write Nand'

Are the above sets all correct to overwrite a possible corrupt RGH Nand?

Any help would be much appropriated


My system is:
Corona mobo
Demon
Coolrunner 3 lite
DVD Replacement PCB flashed with LTU system
 
Last edited:
nofeloniesyet

nofeloniesyet

VIP Member
Jan 16, 2011
4,830
128
Nowhere
lettucekl said:
I have been having issues with the RGH nand on my 360 (retail nand works fine), basically its been a while since i have used the 360 in RGH mode and think there has been a dash update in between the last time i used the RGH mode and did a dash update (i never updated the RGH nand). I booted up the 360 in RGH mode after a few seconds i got a grey screen with white writing and i think an error code of E71, and then the green power light turned red i turned the 360 off and back on again at which point the internal fan was really loud and nothing happen on the 360 so i turned it off again, left it for about a minute and now when i try and turn the 360 on i get the power on audio sound (ding) but no light comes on on the 360. I appear to be able to get the 360 to power on now and again but have noticed that the 360 boots in 480p display and goes to a screen showing the 360 pad and an arrow point to the home button and then the 'A' button, its as if the 360 has been reset back to factory setup mode!

It has been suggested that the RGH nand might have become corrupt, i tried updated the RGH nand via j-runner but now just get the red power light button on the 360 when i turn it on in rgh mode, its over a year since i updated the RGH nand via j-runner and just want to clarify the method i used in updating my RGH nand was correct....

I have a folder from the last time i update my nand with the following files, which i guess the modder supplied to me as well:

checksum.md5
cpukey.txt
C-R.bin
fcrt_dec.bin
fcrt_en.bin
key.bin
KV_dec.bin
KV_en.bin
KV_info.txt
nanddump1.bin
nanddump2.bin
smc_config.bin
SMC_dec.bin
SMC_en.bin
upflash(120320131741).bin
upflash.bin

In j-runner i....

clicked on 'Load Source' and browsed to nanddump1.bin (from the above list)
clicked on 'Load Extra' and browsed to nanddump2.bin
CPU key was showing in the relevant window
clicked 'Nand Compare' all came back fine
selected dash version 16547 from the dash version drop downlist
selected 'RGH2'
and then clicked on 'Write Nand'

Are the above sets all correct to overwrite a possible corrupt RGH Nand?

Any help would be much appropriated


My system is:
Corona mobo
Demon
Coolrunner 3 lite
DVD Replacement PCB flashed with LTU system
Click to expand...
if ur in the usa and want to send this in im sure i can get it going :)
 
L

lettucekl

Full Member
Feb 5, 2014
27
0
Yeah i Oggy from the UK on these very forums did the install for me. I contacted him about it and said he could take a look but since havent heard anything from him.

Does the DemoN need to be turned on (blue led light) or turned off to read the retail Nand in jrunner?
 
L

lettucekl

Full Member
Feb 5, 2014
27
0
Well if i have the DemoN turned off (no blue light) so i can read the retail nand i keep getting the error message 'manufacturer for code FF not found' in jrunner, any ideas what this message means?
 
You must log in or register to reply here.