Team-Xecuter Community

Hello all,

I have a falcon v2 (2008) with a R-jtag ultimate kit from tx

I installed the qcb (4 of them), connected the wires, installed the programmer, used jrunner, got the nand (4 times), created the xell, sent it to the console, all went well.

now when I boot it i get the 5, 7 and 11 oclock red lights flashing and nothing.

The console was flashed with lt3.0+ (benq) and was working before.

the post log is as follows....
Code: 
Waiting for POST to change
Post 10 - Payload/1BL started
Post 18 - FETCH_CONTENTS
Post 58 - INIT_HYPERVISOR
Post 18 - FETCH_CONTENTS
Post 38 - SIG_VERIFY_4BL_CD
Post 18 - FETCH_CONTENTS
Post 38 - SIG_VERIFY_4BL_CD
Post 18 - FETCH_CONTENTS
Post 38 - SIG_VERIFY_4BL_CD
Post 18 - FETCH_CONTENTS
Post 58 - INIT_HYPERVISOR
Post 18 - FETCH_CONTENTS
Post 38 - SIG_VERIFY_4BL_CD
Post 18 - FETCH_CONTENTS
Post 38 - SIG_VERIFY_4BL_CD
Post 18 - FETCH_CONTENTS
Post 78 - INIT_STFS_DRIVER
Post 18 - FETCH_CONTENTS
Post 38 - SIG_VERIFY_4BL_CD
Post 18 - FETCH_CONTENTS
Post 78 - INIT_STFS_DRIVER
Post 18 - FETCH_CONTENTS
Post 38 - SIG_VERIFY_4BL_CD
Post 18 - FETCH_CONTENTS
Post 58 - INIT_HYPERVISOR
Post 74 - INIT_SHADOWBOOT
Post 15 - FETCH_OFFSET
Post 1B - RC4_DECRYPT
Post 1C - SHA_COMPUTE
Post 1D - SIG_VERIFY
Post 1E - BRANCH
Post 20 - CB entry point reached
Post 21 - INIT_SECOTP
Post A0 - Panic - VERIFY_SECOTP_6
Post 20 - CB entry point reached
Post 20 - CB entry point reached
Post 30 - VERIFY_OFFSET_4BL_CD
Post 70 - INIT_VIDEO_DRIVER
Post 70 - INIT_VIDEO_DRIVER
Post 70 - INIT_VIDEO_DRIVER
Post 30 - VERIFY_OFFSET_4BL_CD
Post 70 - INIT_VIDEO_DRIVER
Post 70 - INIT_VIDEO_DRIVER
Post 30 - VERIFY_OFFSET_4BL_CD
Post 70 - INIT_VIDEO_DRIVER
Post 70 - INIT_VIDEO_DRIVER
Post 70 - INIT_VIDEO_DRIVER
Post 70 - INIT_VIDEO_DRIVER
Post 11 - FSB_CONFIG_PHY_CONTROL
Post 12 - FSB_CONFIG_RX_STATE
Post 1A - RC4_INITIALIZE
Post 1B - RC4_DECRYPT
Post 1C - SHA_COMPUTE
Post 1D - SIG_VERIFY
Post 1E - BRANCH
Post 20 - CB entry point reached
Post 21 - INIT_SECOTP
Post A0 - Panic - VERIFY_SECOTP_6
Post 20 - CB entry point reached
Post 20 - CB entry point reached
Post 70 - INIT_VIDEO_DRIVER
Post 30 - VERIFY_OFFSET_4BL_CD
Post 70 - INIT_VIDEO_DRIVER
Post 70 - INIT_VIDEO_DRIVER
Post 30 - VERIFY_OFFSET_4BL_CD
Post 70 - INIT_VIDEO_DRIVER
Post 70 - INIT_VIDEO_DRIVER
Post 70 - INIT_VIDEO_DRIVER
Post 70 - INIT_VIDEO_DRIVER
Post 70 - INIT_VIDEO_DRIVER
Post 40 - Entrypoint of CD reached
Post 70 - INIT_VIDEO_DRIVER
Post 11 - FSB_CONFIG_PHY_CONTROL
Post 12 - FSB_CONFIG_RX_STATE
Post 18 - FETCH_CONTENTS
Post 19 - HMACSHA_COMPUTE
Post 1B - RC4_DECRYPT
Post 1C - SHA_COMPUTE
Post 1D - SIG_VERIFY
Post 1E - BRANCH
Post 20 - CB entry point reached
Post 21 - INIT_SECOTP
Post A0 - Panic - VERIFY_SECOTP_6
Post 20 - CB entry point reached
Post 20 - CB entry point reached
Post 20 - CB entry point reached
Post 20 - CB entry point reached
Post 20 - CB entry point reached
Post 20 - CB entry point reached
Post 20 - CB entry point reached
Post 20 - CB entry point reached
Post 70 - INIT_VIDEO_DRIVER
Post 20 - CB entry point reached
Post 70 - INIT_VIDEO_DRIVER
Post 30 - VERIFY_OFFSET_4BL_CD
Post 70 - INIT_VIDEO_DRIVER
Post 70 - INIT_VIDEO_DRIVER
Post 70 - INIT_VIDEO_DRIVER
Post 70 - INIT_VIDEO_DRIVER
Post 70 - INIT_VIDEO_DRIVER
Post 70 - INIT_VIDEO_DRIVER
Post 70 - INIT_VIDEO_DRIVER
Post 70 - INIT_VIDEO_DRIVER
I have probably made a mistake while soldering the QCB but with this POST log can you tell me where to look at knowing that all the "nand" part (read and write) seems to be ok...

Thanks a lot for the help