ok i just tried martin and it didnt unlock and the resistor got hot that can`t be right can it ?
Question for the pros
- Thread starter AudioProUK
- Start date
rdubbs007
VIP Member
The resistor should NOT be getting hot. Did you cut the trace properly and test with a multimeter for continuity to make sure there is none?
all i use is tx products and ive had to do few times not many but ive seen it happen but i also wonder if it has to do with me usin a laptop to flash . i kno by logic if pcb has fw on it should intro but there are some times it dont could be due to bad flash
---------- Post added at 08:30 ---------- Previous post was at 08:26 ----------
if resistor is hot then ure not through trace all the way i always gotta double check the mx chips
---------- Post added at 08:30 ---------- Previous post was at 08:26 ----------
if resistor is hot then ure not through trace all the way i always gotta double check the mx chips
Ok i have a new issue .
I have dumped the nand from the slim via flash360
it gives e this info in 360 flash dump tool :
kv : 2
console id : 0A518D4***
serial : 46452430****
region : 0x02FE | PAL/EU
osig : PLDS DG-16D4S 0225
dvd key : 3FF2C14984916C94B8FB04723566****
So i flashed the drive using jungle flasher and LTPlus-0225-v3.0
locked the drive
bridged the trace i cut (and tested )
when i insert a disk i get a xbox 360 logo with both Original disk and back up .
Any ideas ??
I have dumped the nand from the slim via flash360
it gives e this info in 360 flash dump tool :
kv : 2
console id : 0A518D4***
serial : 46452430****
region : 0x02FE | PAL/EU
osig : PLDS DG-16D4S 0225
dvd key : 3FF2C14984916C94B8FB04723566****
So i flashed the drive using jungle flasher and LTPlus-0225-v3.0
locked the drive
bridged the trace i cut (and tested )
when i insert a disk i get a xbox 360 logo with both Original disk and back up .
Any ideas ??
Last edited:
jsinger47
Troll Eating Dogs
Yes the problem is that you didn't read the tutorial. YOU CANNOT MANUAL SPOOF SLIMS
Martin C
VIP Member
ok, so theres no way to put it right ?
---------- Post added at 17:18 ---------- Previous post was at 17:18 ----------
yeah rgh
---------- Post added at 17:18 ---------- Previous post was at 17:18 ----------
yeah rgh
Martin C
VIP Member
jsinger47
Troll Eating Dogs
if you didn't slimkey, or full dump your drive, there is NO WAY you can get a slim drive to work in the console
if its RGH, you can always throw a phat drive in there (make sure to enable nfcrt patches)
EDIT: unless you use 0272 and lizfix (forgot about that)
if its RGH, you can always throw a phat drive in there (make sure to enable nfcrt patches)
EDIT: unless you use 0272 and lizfix (forgot about that)
Last edited:
Martin C
VIP Member
OP - did you manually spoof your slim. Yep, that won't work.
You might be able to build a slim firmware with your DVD key with lizfix. As you're patching out fcrt.bin, it might work.
You might be able to build a slim firmware with your DVD key with lizfix. As you're patching out fcrt.bin, it might work.
dang , which is it ...lol ...
---------- Post added at 17:39 ---------- Previous post was at 17:38 ----------
ok i`ll give that a go ...thanks
---------- Post added at 17:39 ---------- Previous post was at 17:38 ----------
ok i`ll give that a go ...thanks
jsinger47
Troll Eating Dogs
you can ONLY do this if you flash 0272 fw to the drive
0225 fw cannot be manual spoofed (or lizfixed) whatsoever
if you choose to use 0272 fw, once again nofcrt patches
Last edited:
sweet , i`ll use 0272 then it doesnt really matter as long as i get the drive going . If there a tut for using lizfix ?
jsinger47
Troll Eating Dogs
