QUESTION how many ecc for corona 4GB

[modguru]

i just have find 2 one it is in the jrunner and one with that name CORONA_4GB_DGXv2.ecc i have try both with every possible wiring with no luck . at the moment . my question is that ..
we have any other ecc for the corona 4GB or it is only this two .
thanks in advance

 

[BL4K3Y]

If you are having issues with the DGX, post some images of your install along with an explanation of what you have done so far.

A J-Runner log will help us to help you as well .

 

[firess]

We need to know everything in order to help you. What corona motherboard you have V2 or V4. Wire lengths that you used.

Pictures are worth a thousands words they say.

 

[modguru]

here is my photos . and the right now setup .

there is nothing wrong with the pad under the xclub .

the story is endless glitch in normal timing with no xell ... the only diference is when i cut the post out short the green led bring in every glitch for ms and not like normal 1- 2 sec green

i use wire AWG 26 multicore
and i have dip 8 on
i have try the laternate v2 ecc and the first one . with no luck at the moment . but i thing this console has not future from me ... i am on 3 day today and it will be my last on it . if something elese comes out i will give it a try then .

 

[firess]

your post out should be 50cm
and your cpu rst try 8cm to 12 cm

I did a v2 a couple days ago and worked fine took about a minute to boot xell

 

[modguru]

i have try this post out from 330 cm and lower any possible combo no luck

 

[firess]

what about cpu rst on C5R11

 

[modguru]

same thing no change endless glitch with no xell i have order 5 dgx more and i will waiting in case that dgx has something wrong . is the only thing i am afraid .

 

[firess]

this is what mine looks like and works on both trinity corona v1 and v2 so far without any prolems.

Both corona's with coms port to get key

 

[modguru]

sorry your 50 cm cable is in D point . and as far as i know this point is cpu reset . not the post out .
sorry my mistake i see is in your C POINT .
did you use alternate ecc for corona or the ecc from the jrunner ?

my second thoght was to write the stock and to make update in 16202 and after that to start all the procces from the begining . . can anyone confirm that maybe something will be change in 16202 ? .

 

[firess]

i used the one from jrunner
and one corona was on 15??? and the other one was on 16202 so you shouldnt have to update

 

[modguru]

i will not thanks alot for your help .

 

[firess]

some times it just takes awhile to glitch if everything is hooked up it would work.

The only thing i did differently than you on this is i left the 4g r/w kit on and wrote everything through that.

 

[modguru]

and here is a video http://youtu.be/dmWk8m-865s

 

[WalangAlam]

I used the original blue wire from the dgx or cr3 lite for post_out or C and orange from phat wires of cr3 lite or the yellow wire from the dgx for cpu_rst or point D. Those are just the two important things. Done 3 coronas 4gb with good glitch time. Dash version like 16202 doesn't matter. I used router/http to get the cpu key and most of the time it displays xell reloaded to monitor with hdmi cable too. I used original ecc from j-runner. CPU_rst is soldered to R4P4 or the point above that word (too lazy to remove xclamp). DGX placement is beside the nand points.

 

[modguru]

acording to what you write you use 55 cm for post out C . and for cpu reset D 8 cm . is that correct ?

 

[modguru]

final . i have return the console to stock 15574 . th console open normaly ..
i update the console to stock 16202 dashboard . i made all the procces from the start backup and everything and i use from the coolrunner cable the blue wire 55 cm for the point C ( post out ) and the orange wire 8cm for the point D ( cpu reset ) that i have solder to the pad R4P4 . i will post photos to look .
everything elese was as short as possible after 2 min i have take the cpu key ...
thanks to anyone has offering to help . i will post photos from my install in a whille

 

[rogerdodger]

I can't really make out from the photo but it looks to me that you have all the dip switches on the DGX set to ON ? Only no8 should be ON for corona

edit: scratch that, i just loaded the picture in full view, they seem correct. Sorry.

 

[firess]

final . i have return the console to stock 15574 . th console open normaly ..
i update the console to stock 16202 dashboard . i made all the procces from the start backup and everything and i use from the coolrunner cable the blue wire 55 cm for the point C ( post out ) and the orange wire 8cm for the point D ( cpu reset ) that i have solder to the pad R4P4 . i will post photos to look .
everything elese was as short as possible after 2 min i have take the cpu key ...
thanks to anyone has offering to help . i will post photos from my install in a whille

Good stuff man glad to see that you have it working

 

[WalangAlam]

acording to what you write you use 55 cm for post out C . and for cpu reset D 8 cm . is that correct ?

Correct. Work like a charms. Never failed me so far. Another good thing with that is, the wires are already provided. Wires placement doesn't even matter, my postout and cpureset wires are everywhere in my mobo.