R-JTAG Alt point or repair

Status
Not open for further replies.
E

eyre657

Noob Account
Aug 20, 2013
7
0
Ok here's the situation,

My brother has bought my nephew a r-jtag ultimate kit for his jasper system and he tried to install it himself :facepalm:, instead of waiting for me to install it like we initially agreed.
I have just spent the last hour re-soldering the three small boards ( I cant think of the names at moment :redface: ) and I have just looked at the r-jtag board ( Its been a long day :D ) and the solder pad for point F has been pulled :facepalm:.

My question to you fine gentlemen is, is there an alternate point or pin for point F and if so, where, or failing that is it possible to scrape some of the board away to reach a trace? ( its been ages since ive worked with something so small )

FYI, the console is a "virgin" and the only time its been opened is when I cleaned it out a few weeks ago, I will post more information and pictures tomorrow if needed ( to tired tonight ).

Any help would be very appreciated, thanks :smile:
 
E

eyre657

Noob Account
Aug 20, 2013
7
0
Hi bl4k3y,

This is starting to pis me of, I managed to solder the wire to a copper trace and I have just been trying dump the NAND only to have an error with j runner ( Device not found ), so I have rechecked all connections and solder points ( no problems there :confused: ) and I have desoldered the 5v wire to try to boot the xbox normally, to which I have been greeted with 3 red lights and a 0001 error.

Do you or anyone else have any idea what could be causing this?

Any info would be appreciated thanks.

While I was writing this my brother told me that when he removed the GPU x clamp he slipped and removed a little brown resistor ( I think ), but he didn't think it would matter and carried on with the QSB install.

Due to the fact that I keep my workbench extremely clean I will try to find it tomorrow and I post a photo of the damage to see if anyone can help with it :wink:
 
Last edited:
BrockThunderjam

BrockThunderjam

VIP Member
Jun 25, 2013
1,503
88
You need to post pics of your install.
 
nofeloniesyet

nofeloniesyet

VIP Member
Jan 16, 2011
4,830
128
Nowhere
eyre657 said:
Hi bl4k3y,

This is starting to pis me of, I managed to solder the wire to a copper trace and I have just been trying dump the NAND only to have an error with j runner ( Device not found ), so I have rechecked all connections and solder points ( no problems there :confused: ) and I have desoldered the 5v wire to try to boot the xbox normally, to which I have been greeted with 3 red lights and a 0001 error.

Do you or anyone else have any idea what could be causing this?

Any info would be appreciated thanks.

While I was writing this my brother told me that when he removed the GPU x clamp he slipped and removed a little brown resistor ( I think ), but he didn't think it would matter and carried on with the QSB install.

Due to the fact that I keep my workbench extremely clean I will try to find it tomorrow and I post a photo of the damage to see if anyone can help with it :wink:
Click to expand...
"While I was writing this my brother told me that when he removed the GPU x clamp he slipped and removed a little brown resistor ( I think ), but he didn't think it would matter and carried on with the QSB install."

LOL :facepalm:

post good clean pics of all areas soldered to,and we will try to help.
 
Last edited:
E

eyre657

Noob Account
Aug 20, 2013
7
0
I know, he tends to rush into things, I will try to post some pics by the weekend ( I need to get my camera back from a mate ).

Just for querys sake, how much would it cost on here for a r-jtag reinstall ( or touch up ) and to reseat a pulled resistor ?, because ill outsource it the price is decent :)
 
nofeloniesyet

nofeloniesyet

VIP Member
Jan 16, 2011
4,830
128
Nowhere
E

eyre657

Noob Account
Aug 20, 2013
7
0
PICT3379.JPGPICT3380.JPGPICT3381.JPGPICT3382.JPGPICT3383.JPGPICT3384.JPGPICT3385.JPGPICT3386.JPGPICT3387.JPGPICT3388.JPG

Ok here's a few images guys, these have been taken with a crappy 5MP camera so the quality isn't very good, I will touch them up and re-upload if needed.

I have managed to find the broken off resistor and I think its from around near TP106, so if anyone can tell me anything about it I will be grateful :smile:
 
nofeloniesyet

nofeloniesyet

VIP Member
Jan 16, 2011
4,830
128
Nowhere
to op: would you rather send this out to someone for repairs? i can finish and repair it,just pm me for quote.
 
E

eyre657

Noob Account
Aug 20, 2013
7
0
I personaly would get a pro to look at it but as i said in my first post this is my brothers console (and his handywork) i will ask him what he wants to do and then let u know.

Ps are you situated in the uk or us?

Ill try to post some better pics asap ( best cameras at work)

Cheers guys
 
scott1503

scott1503

VIP Member
Jul 21, 2012
1,794
88
Harrogate, North Yorkshire , uk
eyre657 said:
I personaly would get a pro to look at it but as i said in my first post this is my brothers console (and his handywork) i will ask him what he wants to do and then let u know.

Ps are you situated in the uk or us?

Ill try to post some better pics asap ( best cameras at work)

Cheers guys
Click to expand...
Nofeloniesyet is in the USA

but there are many people in the UK or USA that would be able to help you out
 
Last edited:
nofeloniesyet

nofeloniesyet

VIP Member
Jan 16, 2011
4,830
128
Nowhere
scott1503 said:
Nofeloniesyet is in the USA

but there are many people in the UK or USA that would be able to help you out
Click to expand...
yea im usa,but i would talk to oggy,hes the man in the uk to go see :)
 
E

eyre657

Noob Account
Aug 20, 2013
7
0
Ok, after alot of thought I have decided to give my nephew my j-tagged xbox (Im more of a ps3 guy anyway), so if anyone wants a faulty (maybe) jasper phat complete with an r-jtag and a few games for parts of repairs, let me know.

P.S. thanks for the help anyway guys, this is one of best forums ive seen.
 
M

mrdrifta

VIP Member
Jan 31, 2011
325
0
New Zealand
point e on the RJTAG board looks bridged with the onboard xtal. Have you tried removing the retag board and writing the original hand back to the console? Also, i would post close up pics of the damaged areas first. It may be a fairly simple reapiar, but we can't tell without pictures.
 
Status
Not open for further replies.