JASPER R-JTAG+ BB Jasper Strange Problem

I

iTzCalvinFTW

Full Member
Sep 3, 2014
96
0
The Netherlands
Hi Team-Xecuter,

Here is my first CR4 R-JTAG+ Jasper 512mb install. But it doesn't work. Before the CR4 I had a CoolRunner Rev C installed but it was to slow for me so I decided to upgrade to the CR4. I chose for the R-JTAG+ method. I installed the NAND-X wires and in JRunner I created an XeBuild image and selected: JTAG>RJTAG>Aud_Clamp?. Then I wrote the image to my Jasper and installed the CR4. Now here comes the problem. The first time I plugged in the PSU the Xbox turned on by itself without me pressing the power button. I directly unplugged the PSU and looked for solder splashes but I couldn't find any. So I plugged in the PSU and it didn't turn on by itself so I pressed the power button and the ring of light wouldn't turn on but before (when it turned on by itself) it did, so now with no ring of light the fans still spinned up and the debug led on the CR4 turned on and stayed on. A few seconds later you could hear the fans glitching rapidly and the debug LED also flashed rapidly.

Template:


  • Console Type: Jasper
  • Programmer Used: NAND-X & JRP v2
  • NAND Size: 512
  • Dashboard version: 2.0.17150
  • CB Version: 6754
  • Screenshot of NAND details from J-Runner: (attach an image to your post)
  • J-Runner log
  • updflash.bin log (if applicable)
  • Image of the CR4 XL
  • Images of close-up soldering to motherboard (attach images to your post)
  • Detailed Description of the Problem: See above
  • Was the console working before you started: Y
  • Do you get a green debug light appear on the CR4 XL chip every 4-5 seconds: NO
  • How long is the light on for each time: n.a

Images: http://m.imgur.com/a/jNbFh

I changed the STBY_CLK (point B on the CoolRunner) to the alternative point. I hoped it would help but it didn't do anything...

I hope this is enough information, I will be including a video in a few minutes.
Video: http://youtu.be/1nagsAYCn5E

Thank You! Any help is greatly appreciated!
 
Last edited:
I

iTzCalvinFTW

Full Member
Sep 3, 2014
96
0
The Netherlands
I soldered point C to FT6U7 which was wrong, I had left the yellow wire there from the RGH2 install. There is only one problem, my Ring of Light doesn't work :(
 
B

bruno_rv

VIP Member
Jun 8, 2010
181
0
Croatia
I think the ring of light problem has something to do with the rjtag qsb. I think you should resolder the small resistor on the edge of the jtag qsb. I had that problem with old rjtag 1.1 and if i remember it correctly that resistor was causing that problem
 
  • Like
Reactions: iTzCalvinFTW
I

iTzCalvinFTW

Full Member
Sep 3, 2014
96
0
The Netherlands
Krafter said:
Please complete the CR4 Temate.
Click to expand...


Console Type: Jasper
Programmer Used: NAND-X & JRP v2
NAND Size: 512
Dashboard version: 17150
CB Version: e.g 5771
Screenshot of NAND details from J-Runner: http://gyazo.com/e54abb338787d1a511fa1661914b58d0
J-Runner log:
SuccessJtag Selected
Aud_Clamp Selected
R-Jtag Selected
Initializing updflash.bin..
Jasper BB
Nand Initialization Finished
Aud_Clamp de-Selected
Aud_Clamp Selected
R-Jtag de-Selected
R-Jtag Selected
Jasper 512MB Manually Selected

Image of the CR4 XL: http://m.imgur.com/a/jNbFh
Images of close-up soldering to motherboard: http://m.imgur.com/a/jNbFh
Detailed Description of the Problem: The ROL is not working :(
Was the console working before you started: Y
Do you get a green debug light appear on the CR4 XL chip every 4-5 seconds: Y
How long is the light on for each time: 6 seconds
 
I

iTzCalvinFTW

Full Member
Sep 3, 2014
96
0
The Netherlands
bruno_rv said:
I think the ring of light problem has something to do with the rjtag qsb. I think you should resolder the small resistor on the edge of the jtag qsb. I had that problem with old rjtag 1.1 and if i remember it correctly that resistor was causing that problem
Click to expand...
Hmmmm are you sure I need to solder this point? In the official install guide it says I shouldn't. Have a look here. I don't want to burn my console :eek2:. Thank you for your reply!

- - - Updated - - -

Krafter said:
Please complete the CR4 Temate.
Click to expand...
Thanks for your reply!
 
B

bruno_rv

VIP Member
Jun 8, 2010
181
0
Croatia
Not solder. I mean if you already soldered it that resistor makes problems with rol. If you didnt than it doesn matter
 
B

briggs01

VIP Member
Feb 17, 2013
1,324
0
why do you have the grey wire soldered to the resister , it should go to the pad next to it r4b24
 
B

briggs01

VIP Member
Feb 17, 2013
1,324
0
bruno_rv said:
I think the ring of light problem has something to do with the rjtag qsb. I think you should resolder the small resistor on the edge of the jtag qsb. I had that problem with old rjtag 1.1 and if i remember it correctly that resistor was causing that problem
Click to expand...
that doesn't get soldered
 
  • Like
Reactions: iTzCalvinFTW
I

iTzCalvinFTW

Full Member
Sep 3, 2014
96
0
The Netherlands
I

iTzCalvinFTW

Full Member
Sep 3, 2014
96
0
The Netherlands
briggs01 said:
why do you have the grey wire soldered to the resister , it should go to the pad next to it r4b24
Click to expand...
Thanks for your reply, I thought I could also solder it to the resistor. Now I changed it to this. I wanted to use the alternative point because I was afraid that I would damage the normal point.
 
I

iTzCalvinFTW

Full Member
Sep 3, 2014
96
0
The Netherlands
briggs01 said:
I have a jasper , I have just number 4 dip on and it boots as soon as I press the on button
Click to expand...
Thanks for the reply and for the tip! It now boots 1 glitch faster which CAP are you using (or other settings). My jasper still doesn't have a working ring of light. And it keeps freezing, did you use the magic smc? It is not working for me: http://team-xecuter.com/forums/showthread.php?149975-Magic-SMC-Files-R-JTAG-Error-in-JRunner

- - - Updated - - -

briggs01 said:
oh yes sorry mate forgot its a jasper lol
Click to expand...
Ohh no problem! Thanks for the reply!
 
nofeloniesyet

nofeloniesyet

VIP Member
Jan 16, 2011
4,830
128
Nowhere
iTzCalvinFTW said:
Thanks for the reply and for the tip! It now boots 1 glitch faster which CAP are you using (or other settings). My jasper still doesn't have a working ring of light. And it keeps freezing, did you use the magic smc? It is not working for me: http://team-xecuter.com/forums/showthread.php?149975-Magic-SMC-Files-R-JTAG-Error-in-JRunner

- - - Updated - - -



Ohh no problem! Thanks for the reply!
Click to expand...
the resistor at r2r12,right under that number where the jtag qsb solders into the resistor,its that resistor that either needs resoldered or replaced,that will bring the ring of light back and end the freezing.and dont solder the qsb there.iirc it should measure around 8.k ohm.
 
Last edited:
  • Like
Reactions: iTzCalvinFTW
H

h1n1viruz

Junior Member
Jan 20, 2015
24
3
Tip for wire placement stay away from the area directly under the HANA Chip, my jasper would freeze and i rerouted wires and it now works great no freezing.
i put the CPU_RST in one hole and the yellow and white through another. so move the wires down. closer to the xclamps, becareful with the CPU_RST wire not to lift the pad, secure the position of that wire first then work on the others . good luck
 
  • Like
Reactions: iTzCalvinFTW
B

briggs01

VIP Member
Feb 17, 2013
1,324
0
nofeloniesyet said:
the resistor at r2r12,right under that number where the jtag qsb solders into the resistor,its that resistor that either needs resoldered or replaced,that will bring the ring of light back and end the freezing.and dont solder the qsb there.iirc it should measure around 8.k ohm.
Click to expand...
don't you mean R2P12 mate , this one OP is the xbox doing anything or is it dead , if its dead you need to look at this resister as NOFELONIESYET said
 

Attachments

  • Like
Reactions: iTzCalvinFTW
You must log in or register to reply here.