RGH R-JTAG Falcon unable to load into XeLL

[lazai]

Console Type: Falcon
NAND size: 16
Dashboard version: 2.0.16202
CB version: 5774
Screenshot of NAND details from J-Runner:

J-Runner log:

[B][B][B][B][B][B]Checking Files[/B][/B][/B][/B][/B][/B][B][B][B][B][B][B]
Finished Checking Files
Version: 10
Flash Config: 0x01198010
CB Version: 5774
Falcon/Opus
Reading Nand to C:\Users\ttessare\Downloads\J-Runner v02 Beta (288) Core Pack\J-Runner v02 Beta (288) Core Pack\output\nanddump1.bin
Reading Nand
Error: 250 reading block 1B4
Done!
in 3:21 min:sec

Reading Nand to C:\Users\ttessare\Downloads\J-Runner v02 Beta (288) Core Pack\J-Runner v02 Beta (288) Core Pack\output\nanddump2.bin
Initializing nanddump1.bin..
Nand Initialization Finished
Reading Nand
Error: 250 reading block 1B4
Done!
in 3:21 min:sec

Comparing...
Reading Nand to C:\Users\ttessare\Downloads\J-Runner v02 Beta (288) Core Pack\J-Runner v02 Beta (288) Core Pack\output\nanddump3.bin
Bad Block ID @ 0x01B4 [Offset: 0x706800]
Bad Block ID  01B4 Found @ 0x03FF [Offset: 0x107BE00]
Block ID 03FF [Offset: 0x107BE00] remapped to Block ID 01B4 [Offset: 0x706800]
Bad Blocks Remapped
Bad Block ID @ 0x01B4 [Offset: 0x706800]
Bad Block ID  01B4 Found @ 0x03FF [Offset: 0x107BE00]
Block ID 03FF [Offset: 0x107BE00] remapped to Block ID 01B4 [Offset: 0x706800]
Bad Blocks Remapped
Nands are the same
Done!
[B][B][B][B][B][B]in 3:21 min:sec

Patching Jasper version 2.3 SMC at offset 0x12BA
XeLL file created Successfully falcon_hack_aud_clamp.bin
Version: 10
Flash Config: 0x01198010
Writing Nand
falcon_hack_aud_clamp.bin
Done!
in 0:18 min:sec

[/B][/B][/B][/B][/B][/B][/B][/B][/B][/B][/B][/B]

POST output from J-Runner (either POST_OUT monitor or RATER output):

[B][B][B][B][B][B][B]Version: 10
[/B][/B][/B][/B][/B][/B][/B]Power Up
Waiting for POST to change
Post 21 - INIT_SECOTP 
Post 01 
Post 31 - FETCH_HEADER_4BL_CD 
Post 01 
Post 31 - FETCH_HEADER_4BL_CD 
Post 01 
Post 31 - FETCH_HEADER_4BL_CD 
Post 01 
Post 21 - INIT_SECOTP 
Post 01 
Post 31 - FETCH_HEADER_4BL_CD 
Post 01 
Post 31 - FETCH_HEADER_4BL_CD 
Post 21 - INIT_SECOTP 
Post 01 
Post 31 - FETCH_HEADER_4BL_CD 
Post 01 
Post 31 - FETCH_HEADER_4BL_CD 
Post 21 - INIT_SECOTP 
Post 01 
Post 31 - FETCH_HEADER_4BL_CD 
Post 01 
Post 31 - FETCH_HEADER_4BL_CD 
Post 21 - INIT_SECOTP 
Post 01 
Post 31 - FETCH_HEADER_4BL_CD 
Post 01 
Post 71 - INIT_AUDIO_DRIVER 
Post 10 - Payload/1BL started 
Post 12 - FSB_CONFIG_RX_STATE 
Post 13 - FSB_CONFIG_TX_STATE 
Post 18 - FETCH_CONTENTS 
Post 19 - HMACSHA_COMPUTE 
Post 1B - RC4_DECRYPT 
Post 1C - SHA_COMPUTE 
Post 1D - SIG_VERIFY 
Post 1E - BRANCH 
Post 20 - CB entry point reached 
Post 21 - INIT_SECOTP 
Post A0 - Panic - VERIFY_SECOTP_6 
Post 70 - INIT_VIDEO_DRIVER 
Post 70 - INIT_VIDEO_DRIVER 
Post 70 - INIT_VIDEO_DRIVER 
Post 70 - INIT_VIDEO_DRIVER 
Post 70 - INIT_VIDEO_DRIVER 
Post 70 - INIT_VIDEO_DRIVER 
Post 70 - INIT_VIDEO_DRIVER 
Post 30 - VERIFY_OFFSET_4BL_CD 
Post 70 - INIT_VIDEO_DRIVER 
Post 70 - INIT_VIDEO_DRIVER 
Post F0 - Panic - VERIFY_OFFSET_CB_B 
Post 70 - INIT_VIDEO_DRIVER 
Post 70 - INIT_VIDEO_DRIVER 
Post 30 - VERIFY_OFFSET_4BL_CD 
Post 10 - Payload/1BL started 
Post 12 - FSB_CONFIG_RX_STATE 
Post 14 - FSB_CONFIG_TX_CREDITS 
Post 1B - RC4_DECRYPT 
Post 1C - SHA_COMPUTE 
Post 1D - SIG_VERIFY 
Post 1E - BRANCH 
Post 20 - CB entry point reached 
Post 21 - INIT_SECOTP 
[B][B][B][B][B][B][B]Post A0 - Panic - VERIFY_SECOTP_6 
[/B][/B][/B][/B][/B][/B][/B]

Image of R-JTAG board:
Images of close-up soldering to motherboard:

Description of problem: Getting A0 errors and can't fix it. Tried all jumper settings 1-8 with different voltages and aud_clamp off/on. Damaged the CPU_RST as u can see the soldering pad came off so i'm using the alternate CPU_RST point. Is this maybe the problem? Had redone the solderings many times especially the CPU_RST but no help. Any idea?

Was the console working before you started: Y

 

[BrockThunderjam]

Have you tried booting stock since you did your repair?

Sent from my Nexus 4 using Tapatalk 2

 

[lazai]

I just have to flash back the stock nand and take off the 5v cable from the r-jtag right? No reactions from xbox and monitor post..

 

[BrockThunderjam]

I just have to flash back the stock nand and take off the 5v cable from the r-jtag right? No reactions from xbox and monitor post..

That should do it.

Sent from my Nexus 4 using Tapatalk 2

 

[Martin C]

Tried all jumper settings 1-8 with different voltages.

There's your problem - read the guide.

 

[lazai]

Sure i've read it and tried it with 7 ON 8 OFF 'cause of the Falcon and 1-6 OFF first and tested on after another but i can't get the box running with stock anymore so it's another problem with it..

 

[Dark_Riku]

Martin is right..I can visually see where you have gone wrong..

Not sure if it's my phone..you have soldered to STBY_CLK? that should not be soldered too..that is for RGH only.

But...if you read the guide, you can see where you have went wrong...specifically the JTAG_QSB. That's all I am going to say. If you can't read simple instructions..You don't deserve a direct answer to the problem.

 

[briggs01]

i agree it does look like it is soldered , go over all soldering then start again you may get better results

 

[Dark_Riku]

i agree it does look like it is soldered , go over all soldering then start again you may get better results

Not just the CLK, look closely at the JTAG_QSB, tell me what you notice there..without giving the OP a direct answer. He claims he read the guide, but there's something of importance there.

 

[Taijigamer2]

Oh dear, not going to get very far like that. Well spotted.

 

[BrockThunderjam]

Oh dear, not going to get very far like that. Well spotted.

I've never done an Rjtag, but I can bet you if someone was stuck on something and I knew the answer (which according to you guys is obvious) I would just tell him. I wouldn't be such a **** about it.

Sent from my Nexus 4 using Tapatalk 2

 

[Utmad]

Just read the guide and all will become clear

give you a clue 1-3

 

[Dark_Riku]

I've never done an Rjtag, but I can bet you if someone was stuck on something and I knew the answer (which according to you guys is obvious) I would just tell him. I wouldn't be such a **** about it.

Sent from my Nexus 4 using Tapatalk 2

You're missing the point. I'm not being an ass about it. The OP has "read" the guide apparently so he should know the answer is obvious. It's not rocket science.

 

[BrockThunderjam]

You're missing the point. I'm not being an ass about it. The OP has "read" the guide apparently so he should know the answer is obvious. It's not rocket science.

OK so just tell him his solder jumper is wrong.

Sent from my Nexus 4 using Tapatalk 2

 

[Dark_Riku]

OK so just tell him his solder jumper is wrong.

Sent from my Nexus 4 using Tapatalk 2

People don't learn by being spoonfed. The guide answers EVERYTHING.

 

[BrockThunderjam]

People don't learn by being spoonfed. The guide answers EVERYTHING.

I agree, however in this case he just missed something. It happens man. He filled out the template and obviously put in effort. Just be humane is my point.

Sent from my Nexus 4 using Tapatalk 2

 

[Utmad]

I hope you mean human and not humane don't want no killing going on

 

[BrockThunderjam]

I hope you mean human and not humane don't want no killing going on

Ha, no meant humane. Not sure what that had to do with killin'.

Sent from my Nexus 4 using Tapatalk 2