Rater not turning off console, and sometimes stuck.

[XtregaGames]

Hello. I have two problems with my R-jtag install. Not with booting, but with the rater. I use the rater and it never shuts the console off. I have to shut it off manually, it will turn it on.
Another problem is that sometimes it gets stuck at Post 79 - LOAD_XAM and will not send the shutdown signal, it thinks it is still trying to boot. So if I turn it off and on the rater score thinks it is still on same boot. (it wont put the comma after the boot number.

Things I have tried: re soldering the post out qsb, always solder with amtech flux. still the same.


I will upload some pictures in a moment.

Here is a screenshot of when it gets stuck.

 

[gavin_darkglide]

It should wait 20 seconds before shutting down. Also the rater wont shut down if the nand wires arent connected.

 

[jsinger47]

You are missing the green nand wire to power down. Just like the 100 other threads.

What type of console do you have.

I bet Falcon. Adjust the power mode.

In the case of a spelling error, I blame Tapatalk.

 

[XtregaGames]

Sorry, I did not know it needed nand wires also. It now shuts off, but sometimes gets stuck at Post 79 - LOAD_XAM . It is a jasper 512mb.

 

[jsinger47]

Sorry, I did not know it needed nand wires also. It now shuts off, but sometimes gets stuck at Post 79 - LOAD_XAM . It is a jasper 512mb.

Show pictures. I bet your jtag wiring is to blame.

In the case of a spelling error, I blame Tapatalk.

 

[XtregaGames]

 

[XtregaGames]

The only changes I have made after taking picture of jtag board was placing jumper for aud_clamp and soldering aud clamp wire. I tried normal jtag first.

 

[gavin_darkglide]

I would look at adjusting the power mode, like j-singer suggested. this is normally not a Jasper problem, but every console is different. also dont forget to make a new nand image for aud_clamp.

 

[XtregaGames]

I am trying with last power option 1.8v. 1.2v gave a bit better results, but still got stuck once or twice. I guess its not that bad, I will just nudge it. And I have selected aud clamp. It is booting, the problem is only rater not detecting that it has booted.

I have another question. Is it normal that a jasper will only boot with switch 3 on? It wont boot with any other switch. Have tried all of them ONE at a time. Also with alternate cpu_rst point it would not boot at all.

It gets good booting times, lots of instant, but sometimes it takes up to 8 tries.

Aud-clamp did give better instant boot timings.

Oh and how does my solder look?

 

[XtregaGames]

Is this good for a jaasper?

post output

Phat SelectedVersion: 10
Power Up
Waiting for POST to change
Post 1C - SHA_COMPUTE 
Post 5C - INIT_KEYS 
Post 7C 
Post 38 - SIG_VERIFY_4BL_CD 
Post 10 - Payload/1BL started 
Post 11 - FSB_CONFIG_PHY_CONTROL 
Post 12 - FSB_CONFIG_RX_STATE 
Post 13 - FSB_CONFIG_TX_STATE 
Post 14 - FSB_CONFIG_TX_CREDITS 
Post 15 - FETCH_OFFSET 
Post 16 - FETCH_HEADER 
Post 17 - VERIFY_HEADER 
Post 18 - FETCH_CONTENTS 
Post 19 - HMACSHA_COMPUTE 
Post 1A - RC4_INITIALIZE 
Post 1B - RC4_DECRYPT 
Post 1C - SHA_COMPUTE 
Post 1D - SIG_VERIFY 
Post 1E - BRANCH 
Post 20 - CB entry point reached 
Post 21 - INIT_SECOTP 
Post A0 - Panic - VERIFY_SECOTP_6 
Post 70 - INIT_VIDEO_DRIVER 
Post 10 - Payload/1BL started 
Post 11 - FSB_CONFIG_PHY_CONTROL 
Post 12 - FSB_CONFIG_RX_STATE 
Post 13 - FSB_CONFIG_TX_STATE 
Post 14 - FSB_CONFIG_TX_CREDITS 
Post 15 - FETCH_OFFSET 
Post 16 - FETCH_HEADER 
Post 17 - VERIFY_HEADER 
Post 18 - FETCH_CONTENTS 
Post 19 - HMACSHA_COMPUTE 
Post 1A - RC4_INITIALIZE 
Post 1B - RC4_DECRYPT 
Post 1C - SHA_COMPUTE 
Post 1D - SIG_VERIFY 
Post 1E - BRANCH 
Post 20 - CB entry point reached 
Post 21 - INIT_SECOTP 
Post A0 - Panic - VERIFY_SECOTP_6 
Post 70 - INIT_VIDEO_DRIVER 
Post 01 
Post 10 - Payload/1BL started 
Post 11 - FSB_CONFIG_PHY_CONTROL 
Post 12 - FSB_CONFIG_RX_STATE 
Post 13 - FSB_CONFIG_TX_STATE 
Post 14 - FSB_CONFIG_TX_CREDITS 
Post 15 - FETCH_OFFSET 
Post 16 - FETCH_HEADER 
Post 17 - VERIFY_HEADER 
Post 18 - FETCH_CONTENTS 
Post 19 - HMACSHA_COMPUTE 
Post 1A - RC4_INITIALIZE 
Post 1B - RC4_DECRYPT 
Post 1C - SHA_COMPUTE 
Post 1D - SIG_VERIFY 
Post 1E - BRANCH 
Post 20 - CB entry point reached 
Post 21 - INIT_SECOTP 
Post 22 - INIT_SECENG 
Post 30 - VERIFY_OFFSET_4BL_CD 
Post 70 - INIT_VIDEO_DRIVER 
Post 10 - Payload/1BL started 
Post 11 - FSB_CONFIG_PHY_CONTROL 
Post 12 - FSB_CONFIG_RX_STATE 
Post 13 - FSB_CONFIG_TX_STATE 
Post 14 - FSB_CONFIG_TX_CREDITS 
Post 15 - FETCH_OFFSET 
Post 16 - FETCH_HEADER 
Post 17 - VERIFY_HEADER 
Post 18 - FETCH_CONTENTS 
Post 19 - HMACSHA_COMPUTE 
Post 1A - RC4_INITIALIZE 
Post 1B - RC4_DECRYPT 
Post 1C - SHA_COMPUTE 
Post 1D - SIG_VERIFY 
Post 1E - BRANCH 
Post 20 - CB entry point reached 
Post 21 - INIT_SECOTP 
Post 22 - INIT_SECENG 
Post 70 - INIT_VIDEO_DRIVER 
Post 10 - Payload/1BL started 
Post 11 - FSB_CONFIG_PHY_CONTROL 
Post 12 - FSB_CONFIG_RX_STATE 
Post 13 - FSB_CONFIG_TX_STATE 
Post 14 - FSB_CONFIG_TX_CREDITS 
Post 15 - FETCH_OFFSET 
Post 16 - FETCH_HEADER 
Post 17 - VERIFY_HEADER 
Post 18 - FETCH_CONTENTS 
Post 19 - HMACSHA_COMPUTE 
Post 1A - RC4_INITIALIZE 
Post 1B - RC4_DECRYPT 
Post 1C - SHA_COMPUTE 
Post 1D - SIG_VERIFY 
Post 1E - BRANCH 
Post 20 - CB entry point reached 
Post 21 - INIT_SECOTP 
Post 22 - INIT_SECENG 
Post 2F - RELOCATE 
Post 2E - HWINIT 
Post 31 - FETCH_HEADER_4BL_CD 
Post 33 - FETCH_CONTENTS_4BL_CD 
Post 34 - HMACSHA_COMPUTE_4BL_CD 
Post 35 - RC4_INITIALIZE_4BL_CD 
Post 36 - RC4_DECRYPT_4BL_CD 
Post 37 - SHA_COMPUTE_4BL_CD 
Post 3A - BRANCH 
Post 40 - Entrypoint of CD reached 
Post 44 - FETCH_CONTENTS 
Post 45 - HMACSHA_COMPUTE 
Post 46 - RC4_INITIALIZE 
Post 47 - RC4_DECRYPT 
Post 48 - SHA_COMPUTE 
Post 4B - LZX_EXPAND 
Post 4E - FETCH_OFFSET_6BL_CF 
Post 4F - VERIFY_OFFSET_6BL_CF 
Post 51 - LOAD_UPDATE_2 
Post 50 - LOAD_UPDATE_1 
Post 52 - BRANCH 
Post 58 - INIT_HYPERVISOR 
Post 5A - INIT_XEX_TRAINING 
Post 60 - INIT_KERNEL 
Post 61 - INIT_HAL_PHASE_0 
Post 62 - INIT_PROCESS_OBJECTS 
Post 64 - INIT_MEMORY_MANAGER 
Post 65 - INIT_STACKS 
Post 66 - INIT_OBJECT_SYSTEM 
Post 67 - INIT_PHASE1_THREAD 
Post 68 - Started phase 1 Initialization + INIT_PROCESSORS 
Post 69 - INIT_KEY_VAULT 
Post 6A - INIT_HAL_PHASE_1 
Post 6B - INIT_SFC_DRIVER 
Post 11 - FSB_CONFIG_PHY_CONTROL 
Post 1B - RC4_DECRYPT 
Post 1C - SHA_COMPUTE 
Post 1D - SIG_VERIFY 
Post 1E - BRANCH 
Post 20 - CB entry point reached 
Post 21 - INIT_SECOTP 
Post 22 - INIT_SECENG 
Post 33 - FETCH_CONTENTS_4BL_CD 
Post 44 - FETCH_CONTENTS 
Post 45 - HMACSHA_COMPUTE 
Post 48 - SHA_COMPUTE 
Post 4B - LZX_EXPAND 
Post 4D - DECODE_FUSES 
Post 51 - LOAD_UPDATE_2 
Post 52 - BRANCH 
Post 59 - INIT_SOC_MMIO 
Post 5A - INIT_XEX_TRAINING 
Post 5B - INIT_KEYRING 
Post 5C - INIT_KEYS 
Post 5F 
Post 60 - INIT_KERNEL 
Post 69 - INIT_KEY_VAULT 
Post 6C - INIT_SECURITY 
Post 6D - INIT_KEY_EX_VAULT 
Post 70 - INIT_VIDEO_DRIVER 
Post 72 - INIT_BOOT_ANIMATION + XMADecoder & XAudioRender Init 
Post 73 - INIT_SATA_DRIVER 
Post 78 - INIT_STFS_DRIVER 
Post 79 - LOAD_XAM 
Most Fails(cumulative): 0xA0
Shutdown
Power Up
Waiting for POST to change
Post 70 - INIT_VIDEO_DRIVER 
Post 0E 
Post 10 - Payload/1BL started 
Post 11 - FSB_CONFIG_PHY_CONTROL 
Post 12 - FSB_CONFIG_RX_STATE 
Post 13 - FSB_CONFIG_TX_STATE 
Post 14 - FSB_CONFIG_TX_CREDITS 
Post 15 - FETCH_OFFSET 
Post 16 - FETCH_HEADER 
Post 17 - VERIFY_HEADER 
Post 18 - FETCH_CONTENTS 
Post 19 - HMACSHA_COMPUTE 
Post 1A - RC4_INITIALIZE 
Post 1B - RC4_DECRYPT 
Post 1C - SHA_COMPUTE 
Post 1D - SIG_VERIFY 
Post 1E - BRANCH 
Post 20 - CB entry point reached 
Post 21 - INIT_SECOTP 
Post 22 - INIT_SECENG 
Post 70 - INIT_VIDEO_DRIVER 
Post 10 - Payload/1BL started 
Post 11 - FSB_CONFIG_PHY_CONTROL 
Post 12 - FSB_CONFIG_RX_STATE 
Post 13 - FSB_CONFIG_TX_STATE 
Post 14 - FSB_CONFIG_TX_CREDITS 
Post 15 - FETCH_OFFSET 
Post 16 - FETCH_HEADER 
Post 17 - VERIFY_HEADER 
Post 18 - FETCH_CONTENTS 
Post 19 - HMACSHA_COMPUTE 
Post 1A - RC4_INITIALIZE 
Post 1B - RC4_DECRYPT 
Post 1C - SHA_COMPUTE 
Post 1D - SIG_VERIFY 
Post 1E - BRANCH 
Post 20 - CB entry point reached 
Post 21 - INIT_SECOTP 
Post 22 - INIT_SECENG 
Post 70 - INIT_VIDEO_DRIVER 
Post 10 - Payload/1BL started 
Post 11 - FSB_CONFIG_PHY_CONTROL 
Post 12 - FSB_CONFIG_RX_STATE 
Post 13 - FSB_CONFIG_TX_STATE 
Post 14 - FSB_CONFIG_TX_CREDITS 
Post 15 - FETCH_OFFSET 
Post 16 - FETCH_HEADER 
Post 17 - VERIFY_HEADER 
Post 18 - FETCH_CONTENTS 
Post 19 - HMACSHA_COMPUTE 
Post 1A - RC4_INITIALIZE 
Post 1B - RC4_DECRYPT 
Post 1C - SHA_COMPUTE 
Post 1D - SIG_VERIFY 
Post 1E - BRANCH 
Post 20 - CB entry point reached 
Post 21 - INIT_SECOTP 
Post 22 - INIT_SECENG 
Post 70 - INIT_VIDEO_DRIVER 
Post 10 - Payload/1BL started 
Post 11 - FSB_CONFIG_PHY_CONTROL 
Post 12 - FSB_CONFIG_RX_STATE 
Post 13 - FSB_CONFIG_TX_STATE 
Post 14 - FSB_CONFIG_TX_CREDITS 
Post 15 - FETCH_OFFSET 
Post 16 - FETCH_HEADER 
Post 17 - VERIFY_HEADER 
Post 18 - FETCH_CONTENTS 
Post 19 - HMACSHA_COMPUTE 
Post 1A - RC4_INITIALIZE 
Post 1B - RC4_DECRYPT 
Post 1C - SHA_COMPUTE 
Post 1D - SIG_VERIFY 
Post 1E - BRANCH 
Post 20 - CB entry point reached 
Post 21 - INIT_SECOTP 
Post 22 - INIT_SECENG 
Post 20 - CB entry point reached 
Post 70 - INIT_VIDEO_DRIVER 
Post 10 - Payload/1BL started 
Post 11 - FSB_CONFIG_PHY_CONTROL 
Post 12 - FSB_CONFIG_RX_STATE 
Post 13 - FSB_CONFIG_TX_STATE 
Post 14 - FSB_CONFIG_TX_CREDITS 
Post 15 - FETCH_OFFSET 
Post 16 - FETCH_HEADER 
Post 17 - VERIFY_HEADER 
Post 18 - FETCH_CONTENTS 
Post 19 - HMACSHA_COMPUTE 
Post 1A - RC4_INITIALIZE 
Post 1B - RC4_DECRYPT 
Post 1C - SHA_COMPUTE 
Post 1D - SIG_VERIFY 
Post 1E - BRANCH 
Post 20 - CB entry point reached 
Post 21 - INIT_SECOTP 
Post 22 - INIT_SECENG 
Post 70 - INIT_VIDEO_DRIVER 
Post 10 - Payload/1BL started 
Post 11 - FSB_CONFIG_PHY_CONTROL 
Post 12 - FSB_CONFIG_RX_STATE 
Post 13 - FSB_CONFIG_TX_STATE 
Post 14 - FSB_CONFIG_TX_CREDITS 
Post 15 - FETCH_OFFSET 
Post 16 - FETCH_HEADER 
Post 17 - VERIFY_HEADER 
Post 18 - FETCH_CONTENTS 
Post 19 - HMACSHA_COMPUTE 
Post 1A - RC4_INITIALIZE 
Post 1B - RC4_DECRYPT 
Post 1C - SHA_COMPUTE 
Post 1D - SIG_VERIFY 
Post 1E - BRANCH 
Post 20 - CB entry point reached 
Post 21 - INIT_SECOTP 
Post 22 - INIT_SECENG 
Post 70 - INIT_VIDEO_DRIVER 
Post 30 - VERIFY_OFFSET_4BL_CD 
Post 10 - Payload/1BL started 
Post 11 - FSB_CONFIG_PHY_CONTROL 
Post 12 - FSB_CONFIG_RX_STATE 
Post 13 - FSB_CONFIG_TX_STATE 
Post 14 - FSB_CONFIG_TX_CREDITS 
Post 15 - FETCH_OFFSET 
Post 16 - FETCH_HEADER 
Post 17 - VERIFY_HEADER 
Post 18 - FETCH_CONTENTS 
Post 19 - HMACSHA_COMPUTE 
Post 1A - RC4_INITIALIZE 
Post 1B - RC4_DECRYPT 
Post 1C - SHA_COMPUTE 
Post 1D - SIG_VERIFY 
Post 1E - BRANCH 
Post 20 - CB entry point reached 
Post 21 - INIT_SECOTP 
Post A0 - Panic - VERIFY_SECOTP_6 
Post 70 - INIT_VIDEO_DRIVER 
Post 10 - Payload/1BL started 
Post 11 - FSB_CONFIG_PHY_CONTROL 
Post 12 - FSB_CONFIG_RX_STATE 
Post 13 - FSB_CONFIG_TX_STATE 
Post 14 - FSB_CONFIG_TX_CREDITS 
Post 15 - FETCH_OFFSET 
Post 16 - FETCH_HEADER 
Post 18 - FETCH_CONTENTS 
Post 19 - HMACSHA_COMPUTE 
Post 1A - RC4_INITIALIZE 
Post 1B - RC4_DECRYPT 
Post 1C - SHA_COMPUTE 
Post 1D - SIG_VERIFY 
Post 1E - BRANCH 
Post 20 - CB entry point reached 
Post 21 - INIT_SECOTP 
Post 22 - INIT_SECENG 
Post 2F - RELOCATE 
Post 2E - HWINIT 
Post 31 - FETCH_HEADER_4BL_CD 
Post 33 - FETCH_CONTENTS_4BL_CD 
Post 34 - HMACSHA_COMPUTE_4BL_CD 
Post 35 - RC4_INITIALIZE_4BL_CD 
Post 36 - RC4_DECRYPT_4BL_CD 
Post 37 - SHA_COMPUTE_4BL_CD 
Post 3A - BRANCH 
Post 40 - Entrypoint of CD reached 
Post 42 - FETCH_HEADER 
Post 44 - FETCH_CONTENTS 
Post 45 - HMACSHA_COMPUTE 
Post 46 - RC4_INITIALIZE 
Post 47 - RC4_DECRYPT 
Post 48 - SHA_COMPUTE 
Post 4B - LZX_EXPAND 
Post 4E - FETCH_OFFSET_6BL_CF 
Post 4F - VERIFY_OFFSET_6BL_CF 
Post 51 - LOAD_UPDATE_2 
Post 50 - LOAD_UPDATE_1 
Post 52 - BRANCH 
Post 58 - INIT_HYPERVISOR 
Post 5A - INIT_XEX_TRAINING 
Post 60 - INIT_KERNEL 
Post 61 - INIT_HAL_PHASE_0 
Post 63 - INIT_KERNEL_DEBUGGER 
Post 64 - INIT_MEMORY_MANAGER 
Post 65 - INIT_STACKS 
Post 66 - INIT_OBJECT_SYSTEM 
Post 67 - INIT_PHASE1_THREAD 
Post 68 - Started phase 1 Initialization + INIT_PROCESSORS 
Post 69 - INIT_KEY_VAULT 
Post 6A - INIT_HAL_PHASE_1 
Post 11 - FSB_CONFIG_PHY_CONTROL 
Post 1B - RC4_DECRYPT 
Post 1C - SHA_COMPUTE 
Post 1D - SIG_VERIFY 
Post 1E - BRANCH 
Post 20 - CB entry point reached 
Post 21 - INIT_SECOTP 
Post 22 - INIT_SECENG 
Post 3B - PCI_INIT 
Post 44 - FETCH_CONTENTS 
Post 45 - HMACSHA_COMPUTE 
Post 48 - SHA_COMPUTE 
Post 4B - LZX_EXPAND 
Post 51 - LOAD_UPDATE_2 
Post 52 - BRANCH 
Post 59 - INIT_SOC_MMIO 
Post 5A - INIT_XEX_TRAINING 
Post 5B - INIT_KEYRING 
Post 5C - INIT_KEYS 
Post 5F 
Post 60 - INIT_KERNEL 
Post 64 - INIT_MEMORY_MANAGER 
Post 6A - INIT_HAL_PHASE_1 
Post 6C - INIT_SECURITY 
Post 70 - INIT_VIDEO_DRIVER 
Post 72 - INIT_BOOT_ANIMATION + XMADecoder & XAudioRender Init 
Post 73 - INIT_SATA_DRIVER 
Post 78 - INIT_STFS_DRIVER 
Post 79 - LOAD_XAM 
Most Fails(cumulative): 0xA0
Shutdown
Power Up
Waiting for POST to change
Post 08 
Post 78 - INIT_STFS_DRIVER 
Post 10 - Payload/1BL started 
Post 11 - FSB_CONFIG_PHY_CONTROL 
Post 12 - FSB_CONFIG_RX_STATE 
Post 13 - FSB_CONFIG_TX_STATE 
Post 14 - FSB_CONFIG_TX_CREDITS 
Post 15 - FETCH_OFFSET 
Post 16 - FETCH_HEADER 
Post 17 - VERIFY_HEADER 
Post 18 - FETCH_CONTENTS 
Post 19 - HMACSHA_COMPUTE 
Post 1A - RC4_INITIALIZE 
Post 1B - RC4_DECRYPT 
Post 1C - SHA_COMPUTE 
Post 1D - SIG_VERIFY 
Post 1E - BRANCH 
Post 20 - CB entry point reached 
Post 21 - INIT_SECOTP 
Post 22 - INIT_SECENG 
Post 2F - RELOCATE 
Post 2E - HWINIT 
Post 33 - FETCH_CONTENTS_4BL_CD 
Post 34 - HMACSHA_COMPUTE_4BL_CD 
Post 35 - RC4_INITIALIZE_4BL_CD 
Post 36 - RC4_DECRYPT_4BL_CD 
Post 37 - SHA_COMPUTE_4BL_CD 
Post 3A - BRANCH 
Post 40 - Entrypoint of CD reached 
Post 44 - FETCH_CONTENTS 
Post 45 - HMACSHA_COMPUTE 
Post 46 - RC4_INITIALIZE 
Post 47 - RC4_DECRYPT 
Post 48 - SHA_COMPUTE 
Post 4B - LZX_EXPAND 
Post 4E - FETCH_OFFSET_6BL_CF 
Post 4F - VERIFY_OFFSET_6BL_CF 
Post 51 - LOAD_UPDATE_2 
Post 50 - LOAD_UPDATE_1 
Post 52 - BRANCH 
Post 58 - INIT_HYPERVISOR 
Post 5A - INIT_XEX_TRAINING 
Post 61 - INIT_HAL_PHASE_0 
Post 63 - INIT_KERNEL_DEBUGGER 
Post 64 - INIT_MEMORY_MANAGER 
Post 65 - INIT_STACKS 
Post 66 - INIT_OBJECT_SYSTEM 
Post 67 - INIT_PHASE1_THREAD 
Post 68 - Started phase 1 Initialization + INIT_PROCESSORS 
Post 69 - INIT_KEY_VAULT 
Post 6A - INIT_HAL_PHASE_1 
Post 6B - INIT_SFC_DRIVER 
Post 10 - Payload/1BL started 
Post 11 - FSB_CONFIG_PHY_CONTROL 
Post 10 - Payload/1BL started 
Post 1B - RC4_DECRYPT 
Post 1C - SHA_COMPUTE 
Post 1D - SIG_VERIFY 
Post 1E - BRANCH 
Post 20 - CB entry point reached 
Post 21 - INIT_SECOTP 
Post 22 - INIT_SECENG 
Post 2F - RELOCATE 
Post 44 - FETCH_CONTENTS 
Post 45 - HMACSHA_COMPUTE 
Post 48 - SHA_COMPUTE 
Post 4B - LZX_EXPAND 
Post 4D - DECODE_FUSES 
Post 51 - LOAD_UPDATE_2 
Post 52 - BRANCH 
Post 59 - INIT_SOC_MMIO 
Post 5A - INIT_XEX_TRAINING 
Post 5B - INIT_KEYRING 
Post 5C - INIT_KEYS 
Post 5E - INIT_SOC_INT_COMPLETE 
Post 5F 
Post 69 - INIT_KEY_VAULT 
Post 6C - INIT_SECURITY 
Post 6F - INIT_POWER_MODE 
Post 72 - INIT_BOOT_ANIMATION + XMADecoder & XAudioRender Init 
Post 73 - INIT_SATA_DRIVER 
Post 78 - INIT_STFS_DRIVER 
Post 79 - LOAD_XAM 
Most Fails(cumulative): 0xA0
Shutdown
Power Up
Waiting for POST to change
Post 18 - FETCH_CONTENTS 
Post 78 - INIT_STFS_DRIVER 
Post 9D - Panic - VERIFY_SECOTP_3 
Post 10 - Payload/1BL started 
Post 11 - FSB_CONFIG_PHY_CONTROL 
Post 12 - FSB_CONFIG_RX_STATE 
Post 13 - FSB_CONFIG_TX_STATE 
Post 14 - FSB_CONFIG_TX_CREDITS 
Post 15 - FETCH_OFFSET 
Post 16 - FETCH_HEADER 
Post 17 - VERIFY_HEADER 
Post 18 - FETCH_CONTENTS 
Post 19 - HMACSHA_COMPUTE 
Post 1A - RC4_INITIALIZE 
Post 1B - RC4_DECRYPT 
Post 1C - SHA_COMPUTE 
Post 1D - SIG_VERIFY 
Post 1E - BRANCH 
Post 20 - CB entry point reached 
Post 21 - INIT_SECOTP 
Post 22 - INIT_SECENG 
Post 70 - INIT_VIDEO_DRIVER 
Post 10 - Payload/1BL started 
Post 11 - FSB_CONFIG_PHY_CONTROL 
Post 12 - FSB_CONFIG_RX_STATE 
Post 13 - FSB_CONFIG_TX_STATE 
Post 14 - FSB_CONFIG_TX_CREDITS 
Post 15 - FETCH_OFFSET 
Post 16 - FETCH_HEADER 
Post 17 - VERIFY_HEADER 
Post 18 - FETCH_CONTENTS 
Post 19 - HMACSHA_COMPUTE 
Post 1A - RC4_INITIALIZE 
Post 1B - RC4_DECRYPT 
Post 1C - SHA_COMPUTE 
Post 1D - SIG_VERIFY 
Post 1E - BRANCH 
Post 20 - CB entry point reached 
Post 21 - INIT_SECOTP 
Post 22 - INIT_SECENG 
Post 2F - RELOCATE 
Post 2E - HWINIT 
Post 31 - FETCH_HEADER_4BL_CD 
Post 33 - FETCH_CONTENTS_4BL_CD 
Post 34 - HMACSHA_COMPUTE_4BL_CD 
Post 35 - RC4_INITIALIZE_4BL_CD 
Post 36 - RC4_DECRYPT_4BL_CD 
Post 37 - SHA_COMPUTE_4BL_CD 
Post 3A - BRANCH 
Post 40 - Entrypoint of CD reached 
Post 44 - FETCH_CONTENTS 
Post 45 - HMACSHA_COMPUTE 
Post 47 - RC4_DECRYPT 
Post 48 - SHA_COMPUTE 
Post 4B - LZX_EXPAND 
Post 4E - FETCH_OFFSET_6BL_CF 
Post 4F - VERIFY_OFFSET_6BL_CF 
Post 51 - LOAD_UPDATE_2 
Post 50 - LOAD_UPDATE_1 
Post 52 - BRANCH 
Post 58 - INIT_HYPERVISOR 
Post 5A - INIT_XEX_TRAINING 
Post 61 - INIT_HAL_PHASE_0 
Post 62 - INIT_PROCESS_OBJECTS 
Post 63 - INIT_KERNEL_DEBUGGER 
Post 64 - INIT_MEMORY_MANAGER 
Post 65 - INIT_STACKS 
Post 66 - INIT_OBJECT_SYSTEM 
Post 67 - INIT_PHASE1_THREAD 
Post 68 - Started phase 1 Initialization + INIT_PROCESSORS 
Post 69 - INIT_KEY_VAULT 
Post 6A - INIT_HAL_PHASE_1 
Post 6B - INIT_SFC_DRIVER 
Post 10 - Payload/1BL started 
Post 11 - FSB_CONFIG_PHY_CONTROL 
Post 1B - RC4_DECRYPT 
Post 1C - SHA_COMPUTE 
Post 1D - SIG_VERIFY 
Post 1E - BRANCH 
Post 20 - CB entry point reached 
Post 21 - INIT_SECOTP 
Post 22 - INIT_SECENG 
Post 37 - SHA_COMPUTE_4BL_CD 
Post 44 - FETCH_CONTENTS 
Post 45 - HMACSHA_COMPUTE 
Post 4B - LZX_EXPAND 
Post 4D - DECODE_FUSES 
Post 51 - LOAD_UPDATE_2 
Post 52 - BRANCH 
Post 59 - INIT_SOC_MMIO 
Post 5A - INIT_XEX_TRAINING 
Post 5B - INIT_KEYRING 
Post 5C - INIT_KEYS 
Post 5E - INIT_SOC_INT_COMPLETE 
Post 5F 
Post 64 - INIT_MEMORY_MANAGER 
Post 6A - INIT_HAL_PHASE_1 
Post 6C - INIT_SECURITY 
Post 70 - INIT_VIDEO_DRIVER 
Post 72 - INIT_BOOT_ANIMATION + XMADecoder & XAudioRender Init 
Post 73 - INIT_SATA_DRIVER 
Post 78 - INIT_STFS_DRIVER 
Post 79 - LOAD_XAM 
Most Fails(cumulative): 0xA0
Shutdown
Power Up
Waiting for POST to change
Post 08 
Post 78 - INIT_STFS_DRIVER 
Post 10 - Payload/1BL started 
Post 11 - FSB_CONFIG_PHY_CONTROL 
Post 12 - FSB_CONFIG_RX_STATE 
Post 13 - FSB_CONFIG_TX_STATE 
Post 14 - FSB_CONFIG_TX_CREDITS 
Post 15 - FETCH_OFFSET 
Post 16 - FETCH_HEADER 
Post 17 - VERIFY_HEADER 
Post 18 - FETCH_CONTENTS 
Post 19 - HMACSHA_COMPUTE 
Post 1A - RC4_INITIALIZE 
Post 1B - RC4_DECRYPT 
Post 1C - SHA_COMPUTE 
Post 1D - SIG_VERIFY 
Post 1E - BRANCH 
Post 20 - CB entry point reached 
Post 21 - INIT_SECOTP 
Post 22 - INIT_SECENG 
Post 2F - RELOCATE 
Post 2E - HWINIT 
Post 70 - INIT_VIDEO_DRIVER 
Post 10 - Payload/1BL started 
Post 11 - FSB_CONFIG_PHY_CONTROL 
Post 12 - FSB_CONFIG_RX_STATE 
Post 13 - FSB_CONFIG_TX_STATE 
Post 14 - FSB_CONFIG_TX_CREDITS 
Post 15 - FETCH_OFFSET 
Post 16 - FETCH_HEADER 
Post 17 - VERIFY_HEADER 
Post 18 - FETCH_CONTENTS 
Post 19 - HMACSHA_COMPUTE 
Post 1A - RC4_INITIALIZE 
Post 1B - RC4_DECRYPT 
Post 1C - SHA_COMPUTE 
Post 1D - SIG_VERIFY 
Post 1E - BRANCH 
Post 20 - CB entry point reached 
Post 21 - INIT_SECOTP 
Post 22 - INIT_SECENG 
Post 2F - RELOCATE 
Post 2E - HWINIT 
Post 31 - FETCH_HEADER_4BL_CD 
Post 33 - FETCH_CONTENTS_4BL_CD 
Post 34 - HMACSHA_COMPUTE_4BL_CD 
Post 35 - RC4_INITIALIZE_4BL_CD 
Post 36 - RC4_DECRYPT_4BL_CD 
Post 37 - SHA_COMPUTE_4BL_CD 
Post 3A - BRANCH 
Post 40 - Entrypoint of CD reached 
Post 42 - FETCH_HEADER 
Post 44 - FETCH_CONTENTS 
Post 45 - HMACSHA_COMPUTE 
Post 46 - RC4_INITIALIZE 
Post 47 - RC4_DECRYPT 
Post 48 - SHA_COMPUTE 
Post 4B - LZX_EXPAND 
Post 4E - FETCH_OFFSET_6BL_CF 
Post 4F - VERIFY_OFFSET_6BL_CF 
Post 51 - LOAD_UPDATE_2 
Post 50 - LOAD_UPDATE_1 
Post 52 - BRANCH 
Post 58 - INIT_HYPERVISOR 
Post 5A - INIT_XEX_TRAINING 
Post 60 - INIT_KERNEL 
Post 61 - INIT_HAL_PHASE_0 
Post 62 - INIT_PROCESS_OBJECTS 
Post 64 - INIT_MEMORY_MANAGER 
Post 65 - INIT_STACKS 
Post 66 - INIT_OBJECT_SYSTEM 
Post 67 - INIT_PHASE1_THREAD 
Post 68 - Started phase 1 Initialization + INIT_PROCESSORS 
Post 69 - INIT_KEY_VAULT 
Post 6A - INIT_HAL_PHASE_1 
Post 11 - FSB_CONFIG_PHY_CONTROL 
Post 1B - RC4_DECRYPT 
Post 1C - SHA_COMPUTE 
Post 1D - SIG_VERIFY 
Post 1E - BRANCH 
Post 20 - CB entry point reached 
Post 21 - INIT_SECOTP 
Post 22 - INIT_SECENG 
Post 33 - FETCH_CONTENTS_4BL_CD 
Post 44 - FETCH_CONTENTS 
Post 45 - HMACSHA_COMPUTE 
Post 48 - SHA_COMPUTE 
Post 4B - LZX_EXPAND 
Post 4D - DECODE_FUSES 
Post 51 - LOAD_UPDATE_2 
Post 52 - BRANCH 
Post 59 - INIT_SOC_MMIO 
Post 5A - INIT_XEX_TRAINING 
Post 5B - INIT_KEYRING 
Post 5C - INIT_KEYS 
Post 5F 
Post 61 - INIT_HAL_PHASE_0 
Post 69 - INIT_KEY_VAULT 
Post 6C - INIT_SECURITY 
Post 6F - INIT_POWER_MODE 
Post 70 - INIT_VIDEO_DRIVER 
Post 73 - INIT_SATA_DRIVER 
Post 77 - INIT_OTHER_DRIVERS 
Post 78 - INIT_STFS_DRIVER 
Post 79 - LOAD_XAM 
Most Fails(cumulative): 0xA0
Shutdown
Power Up
Waiting for POST to change
Post 70 - INIT_VIDEO_DRIVER 
Post F6 
Post E0 
Post 10 - Payload/1BL started 
Post 11 - FSB_CONFIG_PHY_CONTROL 
Post 12 - FSB_CONFIG_RX_STATE 
Post 13 - FSB_CONFIG_TX_STATE 
Post 14 - FSB_CONFIG_TX_CREDITS 
Post 15 - FETCH_OFFSET 
Post 16 - FETCH_HEADER 
Post 17 - VERIFY_HEADER 
Post 18 - FETCH_CONTENTS 
Post 19 - HMACSHA_COMPUTE 
Post 1A - RC4_INITIALIZE 
Post 1B - RC4_DECRYPT 
Post 1C - SHA_COMPUTE 
Post 1D - SIG_VERIFY 
Post 1E - BRANCH 
Post 20 - CB entry point reached 
Post 21 - INIT_SECOTP 
Post 22 - INIT_SECENG 
Post 70 - INIT_VIDEO_DRIVER 
Post 10 - Payload/1BL started 
Post 11 - FSB_CONFIG_PHY_CONTROL 
Post 12 - FSB_CONFIG_RX_STATE 
Post 13 - FSB_CONFIG_TX_STATE 
Post 14 - FSB_CONFIG_TX_CREDITS 
Post 15 - FETCH_OFFSET 
Post 16 - FETCH_HEADER 
Post 17 - VERIFY_HEADER 
Post 18 - FETCH_CONTENTS 
Post 19 - HMACSHA_COMPUTE 
Post 1A - RC4_INITIALIZE 
Post 1B - RC4_DECRYPT 
Post 1C - SHA_COMPUTE 
Post 1D - SIG_VERIFY 
Post 1E - BRANCH 
Post 20 - CB entry point reached 
Post 21 - INIT_SECOTP 
Post 22 - INIT_SECENG 
Post 2F - RELOCATE 
Post 2E - HWINIT 
Post 31 - FETCH_HEADER_4BL_CD 
Post 33 - FETCH_CONTENTS_4BL_CD 
Post 34 - HMACSHA_COMPUTE_4BL_CD 
Post 35 - RC4_INITIALIZE_4BL_CD 
Post 36 - RC4_DECRYPT_4BL_CD 
Post 37 - SHA_COMPUTE_4BL_CD 
Post 39 - SHA_VERIFY_4BL_CD 
Post 3A - BRANCH 
Post 40 - Entrypoint of CD reached 
Post 42 - FETCH_HEADER 
Post 44 - FETCH_CONTENTS 
Post 45 - HMACSHA_COMPUTE 
Post 46 - RC4_INITIALIZE 
Post 47 - RC4_DECRYPT 
Post 48 - SHA_COMPUTE 
Post 4B - LZX_EXPAND 
Post 4E - FETCH_OFFSET_6BL_CF 
Post 4F - VERIFY_OFFSET_6BL_CF 
Post 51 - LOAD_UPDATE_2 
Post 50 - LOAD_UPDATE_1 
Post 52 - BRANCH 
Post 58 - INIT_HYPERVISOR 
Post 5A - INIT_XEX_TRAINING 
Post 61 - INIT_HAL_PHASE_0 
Post 63 - INIT_KERNEL_DEBUGGER 
Post 64 - INIT_MEMORY_MANAGER 
Post 65 - INIT_STACKS 
Post 66 - INIT_OBJECT_SYSTEM 
Post 67 - INIT_PHASE1_THREAD 
Post 68 - Started phase 1 Initialization + INIT_PROCESSORS 
Post 69 - INIT_KEY_VAULT 
Post 6A - INIT_HAL_PHASE_1 
Post 11 - FSB_CONFIG_PHY_CONTROL 
Post 1B - RC4_DECRYPT 
Post 1C - SHA_COMPUTE 
Post 1D - SIG_VERIFY 
Post 1E - BRANCH 
Post 20 - CB entry point reached 
Post 21 - INIT_SECOTP 
Post 22 - INIT_SECENG 
Post 36 - RC4_DECRYPT_4BL_CD 
Post 44 - FETCH_CONTENTS 
Post 45 - HMACSHA_COMPUTE 
Post 4B - LZX_EXPAND 
Post 4D - DECODE_FUSES 
Post 4E - FETCH_OFFSET_6BL_CF 
Post 51 - LOAD_UPDATE_2 
Post 52 - BRANCH 
Post 59 - INIT_SOC_MMIO 
Post 5A - INIT_XEX_TRAINING 
Post 5B - INIT_KEYRING 
Post 5C - INIT_KEYS 
Post 5F 
Post 61 - INIT_HAL_PHASE_0 
Post 69 - INIT_KEY_VAULT 
Post 6C - INIT_SECURITY 
Post 6F - INIT_POWER_MODE 
Post 70 - INIT_VIDEO_DRIVER 
Post 73 - INIT_SATA_DRIVER 
Post 75 - INIT_DUMP_SYSTEM 
Post 78 - INIT_STFS_DRIVER 
Post 79 - LOAD_XAM 
Most Fails(cumulative): 0xA0
Shutdown
Power Up
Waiting for POST to change
Post 70 - INIT_VIDEO_DRIVER 
Post 81 - Panic - MACHINE_CHECK 
Post 10 - Payload/1BL started 
Post 11 - FSB_CONFIG_PHY_CONTROL 
Post 12 - FSB_CONFIG_RX_STATE 
Post 13 - FSB_CONFIG_TX_STATE 
Post 14 - FSB_CONFIG_TX_CREDITS 
Post 15 - FETCH_OFFSET 
Post 16 - FETCH_HEADER 
Post 17 - VERIFY_HEADER 
Post 18 - FETCH_CONTENTS 
Post 19 - HMACSHA_COMPUTE 
Post 1A - RC4_INITIALIZE 
Post 1B - RC4_DECRYPT 
Post 1C - SHA_COMPUTE 
Post 1D - SIG_VERIFY 
Post 1E - BRANCH 
Post 20 - CB entry point reached 
Post 21 - INIT_SECOTP 
Post A0 - Panic - VERIFY_SECOTP_6 
Post 70 - INIT_VIDEO_DRIVER 
Post 60 - INIT_KERNEL 
Post 10 - Payload/1BL started 
Post 11 - FSB_CONFIG_PHY_CONTROL 
Post 12 - FSB_CONFIG_RX_STATE 
Post 13 - FSB_CONFIG_TX_STATE 
Post 14 - FSB_CONFIG_TX_CREDITS 
Post 15 - FETCH_OFFSET 
Post 16 - FETCH_HEADER 
Post 17 - VERIFY_HEADER 
Post 18 - FETCH_CONTENTS 
Post 19 - HMACSHA_COMPUTE 
Post 1A - RC4_INITIALIZE 
Post 1B - RC4_DECRYPT 
Post 1C - SHA_COMPUTE 
Post 1D - SIG_VERIFY 
Post 1E - BRANCH 
Post 20 - CB entry point reached 
Post 21 - INIT_SECOTP 
Post 22 - INIT_SECENG 
Post 2F - RELOCATE 
Post 2E - HWINIT 
Post 33 - FETCH_CONTENTS_4BL_CD 
Post 34 - HMACSHA_COMPUTE_4BL_CD 
Post 35 - RC4_INITIALIZE_4BL_CD 
Post 36 - RC4_DECRYPT_4BL_CD 
Post 37 - SHA_COMPUTE_4BL_CD 
Post 3A - BRANCH 
Post 40 - Entrypoint of CD reached 
Post 44 - FETCH_CONTENTS 
Post 45 - HMACSHA_COMPUTE 
Post 46 - RC4_INITIALIZE 
Post 47 - RC4_DECRYPT 
Post 48 - SHA_COMPUTE 
Post 4B - LZX_EXPAND 
Post 4E - FETCH_OFFSET_6BL_CF 
Post 4F - VERIFY_OFFSET_6BL_CF 
Post 51 - LOAD_UPDATE_2 
Post 50 - LOAD_UPDATE_1 
Post 52 - BRANCH 
Post 58 - INIT_HYPERVISOR 
Post 5A - INIT_XEX_TRAINING 
Post 60 - INIT_KERNEL 
Post 61 - INIT_HAL_PHASE_0 
Post 62 - INIT_PROCESS_OBJECTS 
Post 63 - INIT_KERNEL_DEBUGGER 
Post 64 - INIT_MEMORY_MANAGER 
Post 65 - INIT_STACKS 
Post 66 - INIT_OBJECT_SYSTEM 
Post 67 - INIT_PHASE1_THREAD 
Post 68 - Started phase 1 Initialization + INIT_PROCESSORS 
Post 69 - INIT_KEY_VAULT 
Post 6A - INIT_HAL_PHASE_1 
Post 6B - INIT_SFC_DRIVER 
Post 11 - FSB_CONFIG_PHY_CONTROL 
Post 1B - RC4_DECRYPT 
Post 1C - SHA_COMPUTE 
Post 1D - SIG_VERIFY 
Post 1E - BRANCH 
Post 20 - CB entry point reached 
Post 21 - INIT_SECOTP 
Post 22 - INIT_SECENG 
Post 2F - RELOCATE 
Post 44 - FETCH_CONTENTS 
Post 45 - HMACSHA_COMPUTE 
Post 48 - SHA_COMPUTE 
Post 4B - LZX_EXPAND 
Post 4D - DECODE_FUSES 
Post 51 - LOAD_UPDATE_2 
Post 52 - BRANCH 
Post 59 - INIT_SOC_MMIO 
Post 5A - INIT_XEX_TRAINING 
Post 5B - INIT_KEYRING 
Post 5C - INIT_KEYS 
Post 5F 
Post 60 - INIT_KERNEL 
Post 69 - INIT_KEY_VAULT 
Post 6C - INIT_SECURITY 
Post 6D - INIT_KEY_EX_VAULT 
Post 70 - INIT_VIDEO_DRIVER 
Post 72 - INIT_BOOT_ANIMATION + XMADecoder & XAudioRender Init 
Post 73 - INIT_SATA_DRIVER 
Post 78 - INIT_STFS_DRIVER 
Post 79 - LOAD_XAM 
Most Fails(cumulative): 0xA0
Shutdown
Power Up
Waiting for POST to change
Post 08 
Post 78 - INIT_STFS_DRIVER 
Post DB - BRANCH_CB_B 
Post 10 - Payload/1BL started 
Post 11 - FSB_CONFIG_PHY_CONTROL 
Post 12 - FSB_CONFIG_RX_STATE 
Post 13 - FSB_CONFIG_TX_STATE 
Post 14 - FSB_CONFIG_TX_CREDITS 
Post 15 - FETCH_OFFSET 
Post 16 - FETCH_HEADER 
Post 17 - VERIFY_HEADER 
Post 18 - FETCH_CONTENTS 
Post 19 - HMACSHA_COMPUTE 
Post 1A - RC4_INITIALIZE 
Post 1B - RC4_DECRYPT 
Post 1C - SHA_COMPUTE 
Post 1D - SIG_VERIFY 
Post 1E - BRANCH 
Post 20 - CB entry point reached 
Post 21 - INIT_SECOTP 
Post 22 - INIT_SECENG 
Post 2F - RELOCATE 
Post 2E - HWINIT 
Post 31 - FETCH_HEADER_4BL_CD 
Post 33 - FETCH_CONTENTS_4BL_CD 
Post 34 - HMACSHA_COMPUTE_4BL_CD 
Post 35 - RC4_INITIALIZE_4BL_CD 
Post 36 - RC4_DECRYPT_4BL_CD 
Post 37 - SHA_COMPUTE_4BL_CD 
Post 3A - BRANCH 
Post 40 - Entrypoint of CD reached 
Post 42 - FETCH_HEADER 
Post 44 - FETCH_CONTENTS 
Post 45 - HMACSHA_COMPUTE 
Post 46 - RC4_INITIALIZE 
Post 47 - RC4_DECRYPT 
Post 48 - SHA_COMPUTE 
Post 4B - LZX_EXPAND 
Post 4E - FETCH_OFFSET_6BL_CF 
Post 4F - VERIFY_OFFSET_6BL_CF 
Post 51 - LOAD_UPDATE_2 
Post 50 - LOAD_UPDATE_1 
Post 52 - BRANCH 
Post 58 - INIT_HYPERVISOR 
Post 5A - INIT_XEX_TRAINING 
Post 60 - INIT_KERNEL 
Post 61 - INIT_HAL_PHASE_0 
Post 63 - INIT_KERNEL_DEBUGGER 
Post 64 - INIT_MEMORY_MANAGER 
Post 65 - INIT_STACKS 
Post 66 - INIT_OBJECT_SYSTEM 
Post 67 - INIT_PHASE1_THREAD 
Post 68 - Started phase 1 Initialization + INIT_PROCESSORS 
Post 69 - INIT_KEY_VAULT 
Post 6A - INIT_HAL_PHASE_1 
Post 11 - FSB_CONFIG_PHY_CONTROL 
Post 1B - RC4_DECRYPT 
Post 1C - SHA_COMPUTE 
Post 1D - SIG_VERIFY 
Post 1E - BRANCH 
Post 20 - CB entry point reached 
Post 21 - INIT_SECOTP 
Post 22 - INIT_SECENG 
Post 37 - SHA_COMPUTE_4BL_CD 
Post 44 - FETCH_CONTENTS 
Post 45 - HMACSHA_COMPUTE 
Post 48 - SHA_COMPUTE 
Post 4B - LZX_EXPAND 
Post 4D - DECODE_FUSES 
Post 51 - LOAD_UPDATE_2 
Post 52 - BRANCH 
Post 59 - INIT_SOC_MMIO 
Post 5A - INIT_XEX_TRAINING 
Post 5B - INIT_KEYRING 
Post 5C - INIT_KEYS 
Post 5F 
Post 60 - INIT_KERNEL 
Post 64 - INIT_MEMORY_MANAGER 
Post 6C - INIT_SECURITY 
Post 6D - INIT_KEY_EX_VAULT 
Post 70 - INIT_VIDEO_DRIVER 
Post 72 - INIT_BOOT_ANIMATION + XMADecoder & XAudioRender Init 
Post 73 - INIT_SATA_DRIVER 
Post 78 - INIT_STFS_DRIVER 
Post 79 - LOAD_XAM 
Most Fails(cumulative): 0xA0
Shutdown
Power Up
Waiting for POST to change
Post 18 - FETCH_CONTENTS 
Post 1C - SHA_COMPUTE 
Post 7C 
Post 40 - Entrypoint of CD reached 
Post 10 - Payload/1BL started 
Post 11 - FSB_CONFIG_PHY_CONTROL 
Post 12 - FSB_CONFIG_RX_STATE 
Post 13 - FSB_CONFIG_TX_STATE 
Post 14 - FSB_CONFIG_TX_CREDITS 
Post 15 - FETCH_OFFSET 
Post 16 - FETCH_HEADER 
Post 17 - VERIFY_HEADER 
Post 18 - FETCH_CONTENTS 
Post 19 - HMACSHA_COMPUTE 
Post 1A - RC4_INITIALIZE 
Post 1B - RC4_DECRYPT 
Post 1C - SHA_COMPUTE 
Post 1D - SIG_VERIFY 
Post 1E - BRANCH 
Post 20 - CB entry point reached 
Post 21 - INIT_SECOTP 
Post 22 - INIT_SECENG 
Post 2F - RELOCATE 
Post 2E - HWINIT 
Post 31 - FETCH_HEADER_4BL_CD 
Post 33 - FETCH_CONTENTS_4BL_CD 
Post 34 - HMACSHA_COMPUTE_4BL_CD 
Post 35 - RC4_INITIALIZE_4BL_CD 
Post 36 - RC4_DECRYPT_4BL_CD 
Post 37 - SHA_COMPUTE_4BL_CD 
Post 3A - BRANCH 
Post 40 - Entrypoint of CD reached 
Post 42 - FETCH_HEADER 
Post 44 - FETCH_CONTENTS 
Post 45 - HMACSHA_COMPUTE 
Post 46 - RC4_INITIALIZE 
Post 47 - RC4_DECRYPT 
Post 48 - SHA_COMPUTE 
Post 4B - LZX_EXPAND 
Post 4E - FETCH_OFFSET_6BL_CF 
Post 4F - VERIFY_OFFSET_6BL_CF 
Post 51 - LOAD_UPDATE_2 
Post 50 - LOAD_UPDATE_1 
Post 52 - BRANCH 
Post 58 - INIT_HYPERVISOR 
Post 5A - INIT_XEX_TRAINING 
Post 60 - INIT_KERNEL 
Post 61 - INIT_HAL_PHASE_0 
Post 62 - INIT_PROCESS_OBJECTS 
Post 64 - INIT_MEMORY_MANAGER 
Post 65 - INIT_STACKS 
Post 66 - INIT_OBJECT_SYSTEM 
Post 67 - INIT_PHASE1_THREAD 
Post 68 - Started phase 1 Initialization + INIT_PROCESSORS 
Post 69 - INIT_KEY_VAULT 
Post 6A - INIT_HAL_PHASE_1 
Post 11 - FSB_CONFIG_PHY_CONTROL 
Post 1B - RC4_DECRYPT 
Post 1C - SHA_COMPUTE 
Post 1D - SIG_VERIFY 
Post 1E - BRANCH 
Post 20 - CB entry point reached 
Post 21 - INIT_SECOTP 
Post 22 - INIT_SECENG 
Post 2F - RELOCATE 
Post 44 - FETCH_CONTENTS 
Post 45 - HMACSHA_COMPUTE 
Post 47 - RC4_DECRYPT 
Post 4B - LZX_EXPAND 
Post 4D - DECODE_FUSES 
Post 51 - LOAD_UPDATE_2 
Post 52 - BRANCH 
Post 59 - INIT_SOC_MMIO 
Post 5A - INIT_XEX_TRAINING 
Post 5B - INIT_KEYRING 
Post 5C - INIT_KEYS 
Post 5E - INIT_SOC_INT_COMPLETE 
Post 5F 
Post 64 - INIT_MEMORY_MANAGER 
Post 6A - INIT_HAL_PHASE_1 
Post 6C - INIT_SECURITY 
Post 6F - INIT_POWER_MODE 
Post 72 - INIT_BOOT_ANIMATION + XMADecoder & XAudioRender Init 
Post 73 - INIT_SATA_DRIVER 
Post 78 - INIT_STFS_DRIVER 
Post 79 - LOAD_XAM 
Most Fails(cumulative): 0xA0
Shutdown
Power Up
Waiting for POST to change
Post 70 - INIT_VIDEO_DRIVER 
Post 7B 
Post 10 - Payload/1BL started 
Post 11 - FSB_CONFIG_PHY_CONTROL 
Post 12 - FSB_CONFIG_RX_STATE 
Post 13 - FSB_CONFIG_TX_STATE 
Post 14 - FSB_CONFIG_TX_CREDITS 
Post 15 - FETCH_OFFSET 
Post 16 - FETCH_HEADER 
Post 17 - VERIFY_HEADER 
Post 18 - FETCH_CONTENTS 
Post 19 - HMACSHA_COMPUTE 
Post 1A - RC4_INITIALIZE 
Post 1B - RC4_DECRYPT 
Post 1C - SHA_COMPUTE 
Post 1D - SIG_VERIFY 
Post 1E - BRANCH 
Post 20 - CB entry point reached 
Post 21 - INIT_SECOTP 
Post A0 - Panic - VERIFY_SECOTP_6 
Post 70 - INIT_VIDEO_DRIVER 
Post 10 - Payload/1BL started 
Post 11 - FSB_CONFIG_PHY_CONTROL 
Post 12 - FSB_CONFIG_RX_STATE 
Post 13 - FSB_CONFIG_TX_STATE 
Post 14 - FSB_CONFIG_TX_CREDITS 
Post 15 - FETCH_OFFSET 
Post 16 - FETCH_HEADER 
Post 17 - VERIFY_HEADER 
Post 18 - FETCH_CONTENTS 
Post 19 - HMACSHA_COMPUTE 
Post 1A - RC4_INITIALIZE 
Post 1B - RC4_DECRYPT 
Post 1C - SHA_COMPUTE 
Post 1D - SIG_VERIFY 
Post 1E - BRANCH 
Post 20 - CB entry point reached 
Post 21 - INIT_SECOTP 
Post 22 - INIT_SECENG 
Post 2F - RELOCATE 
Post 2E - HWINIT 
Post 31 - FETCH_HEADER_4BL_CD 
Post 33 - FETCH_CONTENTS_4BL_CD 
Post 34 - HMACSHA_COMPUTE_4BL_CD 
Post 35 - RC4_INITIALIZE_4BL_CD 
Post 36 - RC4_DECRYPT_4BL_CD 
Post 37 - SHA_COMPUTE_4BL_CD 
Post 3A - BRANCH 
Post 40 - Entrypoint of CD reached 
Post 44 - FETCH_CONTENTS 
Post 45 - HMACSHA_COMPUTE 
Post 46 - RC4_INITIALIZE 
Post 47 - RC4_DECRYPT 
Post 48 - SHA_COMPUTE 
Post 4B - LZX_EXPAND 
Post 4E - FETCH_OFFSET_6BL_CF 
Post 4F - VERIFY_OFFSET_6BL_CF 
Post 51 - LOAD_UPDATE_2 
Post 50 - LOAD_UPDATE_1 
Post 52 - BRANCH 
Post 58 - INIT_HYPERVISOR 
Post 5A - INIT_XEX_TRAINING 
Post 60 - INIT_KERNEL 
Post 61 - INIT_HAL_PHASE_0 
Post 62 - INIT_PROCESS_OBJECTS 
Post 64 - INIT_MEMORY_MANAGER 
Post 65 - INIT_STACKS 
Post 66 - INIT_OBJECT_SYSTEM 
Post 67 - INIT_PHASE1_THREAD 
Post 68 - Started phase 1 Initialization + INIT_PROCESSORS 
Post 69 - INIT_KEY_VAULT 
Post 6A - INIT_HAL_PHASE_1 
Post 6B - INIT_SFC_DRIVER 
Post 11 - FSB_CONFIG_PHY_CONTROL 
Post 1B - RC4_DECRYPT 
Post 1C - SHA_COMPUTE 
Post 1D - SIG_VERIFY 
Post 1E - BRANCH 
Post 20 - CB entry point reached 
Post 21 - INIT_SECOTP 
Post 22 - INIT_SECENG 
Post 33 - FETCH_CONTENTS_4BL_CD 
Post 44 - FETCH_CONTENTS 
Post 45 - HMACSHA_COMPUTE 
Post 48 - SHA_COMPUTE 
Post 4B - LZX_EXPAND 
Post 4D - DECODE_FUSES 
Post 51 - LOAD_UPDATE_2 
Post 52 - BRANCH 
Post 59 - INIT_SOC_MMIO 
Post 5A - INIT_XEX_TRAINING 
Post 5B - INIT_KEYRING 
Post 5C - INIT_KEYS 
Post 5F 
Post 60 - INIT_KERNEL 
Post 64 - INIT_MEMORY_MANAGER 
Post 6C - INIT_SECURITY 
Post 6D - INIT_KEY_EX_VAULT 
Post 70 - INIT_VIDEO_DRIVER 
Post 72 - INIT_BOOT_ANIMATION + XMADecoder & XAudioRender Init 
Post 73 - INIT_SATA_DRIVER 
Post 78 - INIT_STFS_DRIVER 
Post 79 - LOAD_XAM 
Most Fails(cumulative): 0xA0
Shutdown
Reached No. of Boots Required