Rater Not Working & Rater Will Not Boot Console

[morinzo]

Console: Jasper
NAND size: 16
Dashboard version: 2.0.16537
CB version: 6754
Screenshot of NAND details from J-Runner:

J-Runner log:
POST output from J-Runner: Rater and Monitor Post are not working correctly.
updflash.bin log :
Image of R-JTAG board:
Images of close-up soldering to motherboard:


Description of problem: Can't get the Rater or Monitor Post to work properly or to boot the console the 2 imgs below are all the Rater and Monitor Post do, The Console does not turn on.


Was the console working before you started: Yes & It's Still Working


Here is a video showing that the console boots with RJtag. My settings are Aud_Clamp pads 1-3 soldered (the img above shows pad 1-2 soldered but that was before the aud_clamp install), 1.2v, dips 7-8-4, jtag switch on, three way switch in the center and the jumper on 470.

http://s1365.photobucket.com/user/xXIMOIXx/media/2013-09-16_15-41-01_74_zpsc2001c5f.mp4.html

 

[Antalpromille]

Do you have your jrp v2 connected to the QSB and the rater connector?

 

[morinzo]

I got it working now one of the wires was almost out of the connector for the rater so I pushed it in good and now its working but I still have a issue, When the console boots it doesn't shut it down to continue going through the 20 boots and It didnt count the # of cycles it just stayed on 0. I have to press the stop button to get it to turn off.

Phat SelectedVersion: 10
Power Up
Waiting for POST to change
Post 81 - Panic - MACHINE_CHECK 
Post C3 - LZX_EXPAND_3 
Post D3 - FETCH_HEADER_CB_B 
Post F3 - Panic - ENTRY_SIZE_INVALID_CB_B 
Post 83 - Panic - DATA_SEGMENT 
Post FB 
Post 83 - Panic - DATA_SEGMENT 
Post FB 
Post 83 - Panic - DATA_SEGMENT 
Post FB 
Post 03 
Post 7B 
Post 03 
Post 7B 
Post 03 
Post 7B 
Post 03 
Post 0B 
Post 03 
Post 7B 
Post 03 
Post 7B 
Post 03 
Post 9B - Panic - VERIFY_SECOTP_1 
Post 99 
Post 9D - Panic - VERIFY_SECOTP_3 
Post 9F - Panic - VERIFY_SECOTP_5 
Post A5 - Panic - VERIFY_OFFSET_3BL_CC 
Post A1 - Panic - VERIFY_SECOTP_7 
Post A0 - Panic - VERIFY_SECOTP_6 
Post A1 - Panic - VERIFY_SECOTP_7 
Post A0 - Panic - VERIFY_SECOTP_6 
Post A1 - Panic - VERIFY_SECOTP_7 
Post A0 - Panic - VERIFY_SECOTP_6 
Post A1 - Panic - VERIFY_SECOTP_7 
Post A0 - Panic - VERIFY_SECOTP_6 
Post A1 - Panic - VERIFY_SECOTP_7 
Post A0 - Panic - VERIFY_SECOTP_6 
Post A1 - Panic - VERIFY_SECOTP_7 
Post A0 - Panic - VERIFY_SECOTP_6 
Post A1 - Panic - VERIFY_SECOTP_7 
Post A0 - Panic - VERIFY_SECOTP_6 
Post A1 - Panic - VERIFY_SECOTP_7 
Post A0 - Panic - VERIFY_SECOTP_6 
Post A1 - Panic - VERIFY_SECOTP_7 
Post A0 - Panic - VERIFY_SECOTP_6 
Post A1 - Panic - VERIFY_SECOTP_7 
Post A0 - Panic - VERIFY_SECOTP_6 
Post A1 - Panic - VERIFY_SECOTP_7 
Post A0 - Panic - VERIFY_SECOTP_6 
Post A1 - Panic - VERIFY_SECOTP_7 
Post 81 - Panic - MACHINE_CHECK 
Post F9 
Post 81 - Panic - MACHINE_CHECK 
Post F9 
Post 81 - Panic - MACHINE_CHECK 
Post F9 
Post 81 - Panic - MACHINE_CHECK 
Post F9 
Post 81 - Panic - MACHINE_CHECK 
Post F9 
Post 01 
Post 81 - Panic - MACHINE_CHECK 
Post 79 - LOAD_XAM 
Post 01 
Post 79 - LOAD_XAM 
Post 01 
Post 79 - LOAD_XAM 
Post 01 
Post 1B - RC4_DECRYPT 
Post 19 - HMACSHA_COMPUTE 
Post 1D - SIG_VERIFY 
Post 9D - Panic - VERIFY_SECOTP_3 
Post 9F - Panic - VERIFY_SECOTP_5 
Post A5 - Panic - VERIFY_OFFSET_3BL_CC 
Post A1 - Panic - VERIFY_SECOTP_7 
Post A0 - Panic - VERIFY_SECOTP_6 
Post A1 - Panic - VERIFY_SECOTP_7 
Post A0 - Panic - VERIFY_SECOTP_6 
Post A1 - Panic - VERIFY_SECOTP_7 
Post A0 - Panic - VERIFY_SECOTP_6 
Post A1 - Panic - VERIFY_SECOTP_7 
Post A0 - Panic - VERIFY_SECOTP_6 
Post A1 - Panic - VERIFY_SECOTP_7 
Post A0 - Panic - VERIFY_SECOTP_6 
Post A1 - Panic - VERIFY_SECOTP_7 
Post A0 - Panic - VERIFY_SECOTP_6 
Post A1 - Panic - VERIFY_SECOTP_7 
Post A0 - Panic - VERIFY_SECOTP_6 
Post A1 - Panic - VERIFY_SECOTP_7 
Post A0 - Panic - VERIFY_SECOTP_6 
Post A1 - Panic - VERIFY_SECOTP_7 
Post A0 - Panic - VERIFY_SECOTP_6 
Post A1 - Panic - VERIFY_SECOTP_7 
Post 81 - Panic - MACHINE_CHECK 
Post F9 
Post 81 - Panic - MACHINE_CHECK 
Post 01 
Post F9 
Post 01 
Post 79 - LOAD_XAM 
Post 01 
Post 79 - LOAD_XAM 
Post 01 
Post 79 - LOAD_XAM 
Post 01 
Post 9B - Panic - VERIFY_SECOTP_1 
Post 99 
Post 9D - Panic - VERIFY_SECOTP_3 
Post 9F - Panic - VERIFY_SECOTP_5 
Post A4 - Panic - VERIFY_SECOTP_10 
Post A0 - Panic - VERIFY_SECOTP_6 
Post A2 - Panic - VERIFY_SECOTP_8 
Post A3 - Panic - VERIFY_SECOTP_9 
Post AB - Panic - VERIFY_HEADER_4BL_CD 
Post AF - Panic - UNSUPPORTED_RAM_SIZE 
Post B4 - Panic - LZX_EXPAND 
Post B6 - Panic - DECODE_FUSES 
Post B2 - Panic - VERIFY_HEADER 
Post B3 - Panic - SHA_VERIFY 
Post B7 - Panic - UPDATE_MISSING 
Post C4 - LZX_EXPAND_4 
Post C5 - LZX_EXPAND_5 
Post C4 - LZX_EXPAND_4 
Post CB 
Post D1 - READ_FUSES 
Post D0 - CB_A entry point reached 
Post D1 - READ_FUSES 
Post D0 - CB_A entry point reached 
Post E5 
Post 91 - Panic - THERMAL_MANAGEMENT 
Post 90 - Panic - VMX_ASSIST 
Post 91 - Panic - THERMAL_MANAGEMENT 
Post 90 - Panic - VMX_ASSIST 
Post 91 - Panic - THERMAL_MANAGEMENT 
Post 90 - Panic - VMX_ASSIST 
Post 91 - Panic - THERMAL_MANAGEMENT 
Post 90 - Panic - VMX_ASSIST 
Post 91 - Panic - THERMAL_MANAGEMENT 
Post 90 - Panic - VMX_ASSIST 
Post 91 - Panic - THERMAL_MANAGEMENT 
Shutdown

 

[BL4K3Y]

Connect the green and blue QSB cable to the socket on the long QSB - that will turn the console off during RATER testing.

That RATER log doesn't look correct - solder those POST QSB points again.

 

[morinzo]

i have the green and blue wire in the two wire socket on the long v3 qsb. I'll touch up all the points and try again.

 

[BL4K3Y]

i have the green and blue wire in the two wire socket on the long v3 qsb.

The cables and sockets are colour-coded, so you can't really get that wrong.

 

[Martin C]

What's with the nuts and bolts? I suggest returning to stock and making sure the console still works.

 

[morinzo]

Bl4k3y does this one look any better? I touched up all the qsb spots.

Phat Selected
Version: 10
Power Up
Waiting for POST to change
Post 42 - FETCH_HEADER 
Post 52 - BRANCH 
Post D2 - VERIFY_OFFSET_CB_B 
Post D6 - HMACSHA_COMPUTE_CB_B 
Post F6 
Post 86 - Panic - EXTERNAL 
Post F6 
Post 86 - Panic - EXTERNAL 
Post F6 
Post 86 - Panic - EXTERNAL 
Post F6 
Post 86 - Panic - EXTERNAL 
Post F6 
Post 86 - Panic - EXTERNAL 
Post F6 
Post 86 - Panic - EXTERNAL 
Post F6 
Post 86 - Panic - EXTERNAL 
Post F6 
Post 86 - Panic - EXTERNAL 
Post F6 
Post 86 - Panic - EXTERNAL 
Post 1B - RC4_DECRYPT 
Post 1C - SHA_COMPUTE 
Post 1D - SIG_VERIFY 
Post 1E - BRANCH 
Post 20 - CB entry point reached 
Post 21 - INIT_SECOTP 
Post 22 - INIT_SECENG 
Post 2F - RELOCATE 
Post 2E - HWINIT 
Post 31 - FETCH_HEADER_4BL_CD 
Post 33 - FETCH_CONTENTS_4BL_CD 
Post 34 - HMACSHA_COMPUTE_4BL_CD 
Post 35 - RC4_INITIALIZE_4BL_CD 
Post 36 - RC4_DECRYPT_4BL_CD 
Post 37 - SHA_COMPUTE_4BL_CD 
Post 3A - BRANCH 
Post 40 - Entrypoint of CD reached 
Post 42 - FETCH_HEADER 
Post 44 - FETCH_CONTENTS 
Post 45 - HMACSHA_COMPUTE 
Post 46 - RC4_INITIALIZE 
Post 47 - RC4_DECRYPT 
Post 48 - SHA_COMPUTE 
Post 4B - LZX_EXPAND 
Post 4E - FETCH_OFFSET_6BL_CF 
Post 4F - VERIFY_OFFSET_6BL_CF 
Post 51 - LOAD_UPDATE_2 
Post 50 - LOAD_UPDATE_1 
Post 52 - BRANCH 
Post 58 - INIT_HYPERVISOR 
Post 5A - INIT_XEX_TRAINING 
Post 60 - INIT_KERNEL 
Post 61 - INIT_HAL_PHASE_0 
Post 62 - INIT_PROCESS_OBJECTS 
Post 63 - INIT_KERNEL_DEBUGGER 
Post 64 - INIT_MEMORY_MANAGER 
Post 65 - INIT_STACKS 
Post 11 - FSB_CONFIG_PHY_CONTROL 
Shutdown

 

[mrdrifta]

That does look better, it should load right up to POST 79 LOAD XAM. Try with different dip settings and see if it gets any further, console may need a reflow/reball

 

[morinzo]

What's with the nuts and bolts? I suggest returning to stock and making sure the console still works.

That just what I replace the xclamps with, Its the original heatsink bolts with threads on the xclamp end.

Boots fine when returned to stock and boots fine with rjtag installed, i'm just haing issues getting the rater to work properly so I can fine tune.

 

[Taijigamer2]

Post looks better. What settings have u tried so far. There are 18 combinations. Like Blak3y said, make sure your NAND reader wires are soldered/connected to the v3 qsb and rater should do its job. Good luck.

 

[morinzo]

If I'm using Aud_clamp does the 3-way switch and the jumper help with fine tuning or is that just for jtag?

Also is there a spot on the motherboard were i can use my meter and test the post qsb?

 

[Taijigamer2]

As far as I know, the jtag qsb just covers the implementation of the smc hack. If you've already had a successful boot without E79 then that part should be ok. Have you tried all dip settings? Also length of cpu_rst wire and position can play an important part. Your post looks ok. Also check E and F are well soldered and not bridging. Good luck :smile:

 

[RF1911]

That latest post shows xell loaded. Happy tuning

 

[morinzo]

What would cause it to auto boot & shutdown when the motherboard is out of the case but once I install it into the case it no longer auto boots or shutsdown with Rater?

 

[RF1911]

Maybe a blob of solder from top qsb that touches the case?

 

[Taijigamer2]

Chances are some wires have crossed once the chip is pressed under the case. Post a pic of your Rjtag board wired to the v3 qsb if u can. Just check for potential wire crossing/ shorting.