RGH Reading NAND

[bligal]

Hello everybody,

I managed to read my nand twice but they were different so I tried to read again.
Then, something weird happend I'm getting a lot of errors as shown below:

C:\nandpro3>nandpro usb: -r64 234.bin
NandPro v3.0a by Tiros
Looking for usb interface device
Flash Config: 0x00AA3020
Block Size: 128KB Block Limits: 0x000000..0x000FFF
File: 234.bin
Reading
Error:AA22 reading block 2
Error:AA0C reading block 4
Error: 108 reading block 5
Error: 0 reading block 7
Error: 0 reading block 8
Error:8201 reading block 9
Error:AA00 reading block A
Error:AB00 reading block B
Error:AA12 reading block C
Error: 0 reading block E
Error: 204 reading block F
Error: 438 reading block 11
Error: 0 reading block 12
Error:AA00 reading block 13
Error: 0 reading block 14
Error: 0 reading block 15
Error: 0 reading block 16
Error: 0 reading block 17
Error: 0 reading block 18
Error: 0 reading block 19
Error: 0 reading block 1A
Error: 0 reading block 1B
Error: 0 reading block 1C
Error: 0 reading block 1D
Error: 0 reading block 1E
Error: 0 reading block 1F
Error: 0 reading block 20
Error: 0 reading block 21
Error: 0 reading block 22
Error: 0 reading block 23
Error: 0 reading block 24
Error: 0 reading block 25
Error: 0 reading block 26
Error: 0 reading block 27
Error: 0 reading block 28
^C29
C:\nandpro3>nandpro usb: -r64 234.bin
NandPro v3.0a by Tiros
Looking for usb interface device
usb_bulk_read failed -5
Incompatible ARM firmware for this version of NandPro!
usb_bulk_read failed -116
Flash Config: 0x00413787
Block Size: 16KB Block Limits: 0x000000..0x000FFF
File: 234.bin
Reading
usb_bulk_read failed -116

My XBOX is Jasper with 512MB I'm using NAND-X and QSB

soldering seems to be fine and it worked for the two first times.

I tried to restart my PC, Reconnect XBOX PSU, Reconnect NAND-X and nothing...

I tried to press the NAND-X reset buttom maybe it revert it self to older version. I bought NAND-X with ver 3 allready.

Also, I tried to turn the console normaly but it just won't start so I pushed the sync button until it started.


Help, Anybody?

 

[Icy-Tank]

Was your Nand-X hooked up when you started it?

I've killed a couple of nand-x in my life by not remembering to unhook them before turning it on.

Chances are, if you are getting errors...there's a soldering problem. It could have come loose on a bad or a multitude of things...

It may have worked twice prior, but that doesn't mean anything...it can come loose or lose connection at anytime.

 

[BL4K3Y]

Try re-installing your NAND-X drivers and maybe use another USB port.

Your Flash Config looks correct so I don't think there is an issue with your soldering but you may want to provide some images so we can double check.

 

[tonyjandc]

First I do hope you removed your nandx before powering on box . If you didn't goodbye mr nandx . If you did remove nandx before switching on box post some pics of your soldering . Normally nand problems are due to soldering resetting the nandx doesn't revert to older version. But the new rule is no pics no help

As a edit note use rear of pc . I used to use front ports and sometimes encounted problems then went to rear now all ok

 

[bligal]

First I do hope you removed your nandx before powering on box . If you didn't goodbye mr nandx . If you did remove nandx before switching on box post some pics of your soldering . Normally nand problems are due to soldering resetting the nandx doesn't revert to older version. But the new rule is no pics no help

As a edit note use rear of pc . I used to use front ports and sometimes encounted problems then went to rear now all ok

It is possible that the Xbox turned him self on?
I left it alone while reading and found the green led on.
Maybe there was a problem with the electricity I am not sure.

but when I hooked everything up I'm sure that I removed NAND-X

About the picture I will include them tomorrow because I am not home.

 

[BL4K3Y]

If the console was powered on at any point whilst the NAND-X was connected and on, there is a very slim chance of it working again.

However, see my post above and try the suggestions.

 

[bligal]

If the console was powered on at any point whilst the NAND-X was connected and on, there is a very slim chance of it working again.

However, see my post above and try the suggestions.

I already tried that, Even with another computer.
Thanks anyway.

Looks like I will get a new NAND-X

 

[RepairBucks]

Yeah I got a similar error when my Nand-x took a crap on me. I evidently forgot to unplug it once when I turned the console on. Had to send it in for a repair. But you live and you learn...

 

[dBMods]

If you powered up the console with the nand-x connected to it. 99.9% chance it will not work. Most likely that is going to be the issue . Try purchasing another one and try it again. This is one of the reasons i have more then 1 nand-x. Mistakes happen sometime when your not paying attention to what your doing.